• any purpose other than the intended use, • failure to observe the indications and warnings contained in this Manual / Instruction sheet. Comelit Group S.p.A. reserves the right to change the information provided in this Manual / Instruction Sheet at any time and without prior notice.
Description UT8010 Audio module for Ultra entrance panel, IP (ViP) system. Twilight sensor for automatic nameplate backlighting power-off during daytime hours. Omnidirectional digital microphone and double loudspeaker for high-fidelity audio. Audio-visual indications for disabled individuals assistance request can be activated via programming.
Page 5
1. Indicator LEDs 6. Terminal block for connection: calling (green) RTE programmable input: RTE (local system busy (red) lock-release input), DO (door open first startup or restart (flashing red) indication), Activate output, Priority call or Call user lock-release enabled GND SE- RTE and door lock input reference communication enabled negative SE+ electric door lock connection...
Technical specifications GENERAL DATA Type Modular Product height (mm) Product width (mm) Product depth (mm) Product colour Black RAL9005, Transparent, Aluminium Material Polycarbonate, Aluminium alloy Flush mounting Yes, with specific accessory Surface mounting Yes, with specific accessory COMPATIBLE SYSTEMS AUDIO SPECIFICATIONS Microphone MEMS digital audio sensor, omnidirectional Loudspeaker...
Installation The entrance panel is available in flush-mounted or surface-mounted variants: Flush-mounted installation composition table A = Flush-mounted box B = Rain shield C = Flush-mounted module holder with finishing frame 3110/1 3110/2 3110/3 3110/4 3110/1A 3110/2A 3110/3A 3110/4A UT9181 UT9182 UT9184H UT9183...
CLACK! CLACK! CLACK! CLACK! CLACK! CLACK! The button has a nameplate which can be written on (A); alternatively, an adhesive label can be applied (B). The total thickness of the nameplate + adhesive label MAX 0,2 mm must not exceed 0.2 mm. You can visit the website pro.comelitgroup.com to download the PDF to print the entrance panel name cards, using the pre- cut sheets (C) available in our catalogue (Art.
CLACK! CLACK! CLACK! CLACK! CLACK! CLACK! The button has a nameplate which can be written on (A); alternatively, an adhesive label can be applied (B). The total thickness of the nameplate + adhesive label MAX 0,2 mm must not exceed 0.2 mm. You can visit the website pro.comelitgroup.com to download the PDF to print the entrance panel name cards, using the MAX 0,2 mm...
BLUE & WHITE BLUE ORANGE WHITE ORANGE GREEN WHITE GREEN TX TX RX RX NO NC UT8010 UT9200 (MAX 10) Max 20 m. Local door-opener button. Connection with power supply from standard POE switch STANDARD BROWN & WHITE BROWN SWITCH BLUE &...
1596B 1595 120-240 V 120-230 V TX TX RX RX TX TX RX RX NO NC UT8010 UT9200 UT8010 UT9200 (MAX 30) (MAX 15) Max 20 m. Local door-opener button. Connection with separate power supply and non-POE switch NON POE...
Variant for using the external entrance panel relay 12V/24V AC-DC TX TX RX RX NO NC 4A MAX UT8010 UT9200 Variant with safety door lock 12/24V AC/DC TX TX RX RX NO NC UT8010 UT9200...
Module connection Maximum power available for the modules depending on the type of power supply. Power supply Maximum power available [W] Standard PoE 5 PoE from 1440 5 1595 7.5 1596B 15 power supply from floor distribution unit Art. 1440 or power supply with additional power supply unit Art.
WHITE ORANGE GREEN WHITE GREEN TX TX RX RX NO NC BLACK UT8010 UT9200 MAX 10 Max 20 m. Local door-opener button. Max 10 modules (Max 30 modules with additional power supply, see “Connection with separate power supply”). Connection of Touchscreen module Art. UT9270...
1596B 1595 120-230 V 120-240 V TX TX RX RX TX TX RX RX NO NC UT8010 UT8010 UT9270 UT9270 Max 20 m. Local door-opener button. Connection of number keypad module Art. UT9279M 1440 1441 BROWN & WHITE BROWN BLUE & WHITE BLUE...
Programming To perform programming correctly, proceed as follows: Address the button modules (see “Address button modules”) Configure the ViP address for the UT8010 module via ViP Manager (see“Programming via ViP Manager”) III. Program the ViP call addresses via ViP Manager (see“Programming via ViP...
Adjusting the brightness of the button LEDs 1. Press the button for 3 sec., until you hear a beep. Release the button. » if the procedure was completed successfully, you will hear a confirmation tone; the red LED flashes and the button backlighting comes on.
Reset to factory values 1. Press the reset button for approximately 10 sec.: » after 3 seconds you will hear a beep » after 10 seconds you will hear a second beep 2. Release the reset button » if the procedure was completed successfully, you will hear a confirmation tone; the red LED flashes and the button backlighting comes on for the duration of the device restart procedure.
Programming via ViP Manager All device configurations (with the exception of button module addressing) can be carried out via PC and ViP Manager software, which is available to download free of charge from the website pro.comelitgroup.com. For example: • programming call addresses for the buttons •...
Page 25
C E R T I F I E D M A N A G E M E N T S Y S T E M S w w w . c o m e l i t g r o u p . c o m Via Don Arrigoni, 5 - 24020 Rovetta (BG) - Italy...