Advertisement
Quick Links
7
10a
10c
10b
11b
11a
12
14
25
28
PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, etc. as items
relating to ongoing maintenance suggestions and procedures are included.
TECK
1
13
2
4
9a
9b
8a
8b
6
19
20
15
29
18
16
17
21
23
For valves manufactured
after October 2014.
24
26
27
w w w . s p e c s e l e c t . c o m
81T2__ -WMSHWA
Write purchase model number here for future reference
Electronic Exposed
II Flush Valves
®
(with Wallmount Sensor)
3
30a
24VAC
6.4 VDC
5
22
Poppet Pin
Diaphragm
series
30b
31
12"
36"
Wrench for Brass
Renewable Seat
- for previous
Flush Valve
(ordered
separately)
3
29
Filter Screen
Slip Joint Nut Installation
TABLE 1
UR
1.9L
4.2, 4.8 & 6L
0.5L
060507A &
060507A
060508A
062025A
061324A
061323A
210398 Rev. A
models
WC
13L
060507A
Advertisement
Related Manuals for Delta TECK 81T2 -WHSHWA Series
Summary of Contents for Delta TECK 81T2 -WHSHWA Series
- Page 1 81T2__ -WMSHWA series Write purchase model number here for future reference Electronic Exposed TECK II Flush Valves ® (with Wallmount Sensor) 24VAC 6.4 VDC 12” 36” Wrench for Brass Renewable Seat - for previous Flush Valve models (ordered separately) Filter Screen Slip Joint Nut Installation TABLE 1 For valves manufactured...
- Page 2 Wrench for Brass Renewable Seat * Package Quantities May Change. Check the parts section of the latest Delta Commercial Faucet Price List for current quantities. ** For valves manufactured before October 2014, you must replace the sensor module, cap/solenoid, chrome cover and gasket which are included in;...
- Page 3 Product # Fig. 1 114mm (4-1/2") Min. Max. + 11mm ( ” Sensor Box 102 x 102 x 51mm 114mm (4" x 4" x 2") 81T201-WMSHWA 292mm (11½”) 121mm (4¾”) 54mm (2.13”) 76mm Stainless Steel (4-1/2") (3") Coverplate to top of open 330mm (13”) 121mm (4¾”)
- Page 4 Check that the connection of the hardwire converter is made to the electronic board within the electronic flush valve housing. For further technical assistance, call Delta Commercial Technical Service at 1-800-387-8277 (Canada) or 1-877-509-2680 (U.S.A.). Electronic Override Button in Operating Mode: BLUE light flashes once when Electronic Override Button is activated. Should the electronic override button stick, the program will continue to operate and will reset automatically if the electronic override button is repaired or it returns to home position.
- Page 5 Fig. 6 Hardwire Junction Box and Sensor Rough-In (See Fig. 1 for placement of inlet stop.) 4-1/2” square stainless steel plate Stainless Steel 76mm (3”) (box 4” x 4”) Coverplate Minimum Sensor Sensor Box 102 x 102 x 51mm of Sensor (4”...
-
Page 6: Step 6 - Making Adjustments
STEP 6 - MAKING ADJUSTMENTS (Optional: Only required if factory settings are not preferred) • To move from operation mode into set-up mode: remove the plastic plug located in the rear of the sensor module and press the set-up mode button once. A pencil or small screwdriver may be required. When done, place the plug back in the hole. 6.1 Adjusting Sensing Distances: •... -
Page 7: Cleaning Instructions
NOTE: DO NOT USE EXCESSIVE FORCE to close the inlet stop stem. We RECOMMEND that the flushometer be flushed while closing the inlet stop. The noise created by the water flow or the flow into the fixture will stop when the inlet water is shut off. NOTE: Always use DELTA COMMERCIAL GENUINE PARTS to maintain the warranty. EXCESSIVE NOISE: 1. - Page 8 Delta Commercial Faucet Limited Warranty All parts of the Delta® HDF® and TECK® faucets are warranted to the original consumer purchaser to be free from defects in material, finish and workmanship for a period of five (5) years unless otherwise specifically stated in the catalogue and price book. This warranty is made to the original consumer purchaser and shall be effective from date of purchase as shown on purchaser’s receipt.