Advertisement
Quick Links
2
5a
7a
7b
1
10
10
a
10
b
11
11
b
a
12
13
24
27
PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, etc. as items
relating to ongoing maintenance suggestions and procedures are included.
Record model number:
3
Valve Type
0 = W/C (Water Closet)
3 = Urinal
4
6
29
5b
9a
9b
8a
8b
c
18
11
c
19
14
28
17
15
16
20
22
21
28
Filter Screen
23
25
26
w w w . s p e c s e l e c t . c o m
Electronic Exposed
TECK
II Flush Valves
®
(with H 2 Optics
81T2__ 1__ __A - __ __ - MMO
Alternate Flush Volumes
(leave blank if not applicable)
48 = 4.8 litre (1.27 gal) fixed flush (WC only)
Power Option
42 = 4.2 litre (1.1 gal) fixed flush (WC only)
BT = Battery
05 = 0.5 litre (0.13 gal) fixed flush (Urinal only)
HW = Hardwired
0.5L
Poppet Pin
060508A
Diaphragm
)
™
Manual Mechanical
Override
Slip Joint Nut Installation
TABLE 1
UR
WC
4.2, 4.8 & 6L
1.9 & 3.8L
060507A &
060507A
062025A
061324A
061323A
210343 Rev. A
13L
060507A
Advertisement
Related Manuals for Delta TECK II 81T201BT
Summary of Contents for Delta TECK II 81T201BT
- Page 1 Electronic Exposed TECK II Flush Valves ® (with H 2 Optics ™ Record model number: 81T2__ 1__ __A - __ __ - MMO Valve Type Manual Mechanical Override 0 = W/C (Water Closet) 3 = Urinal Alternate Flush Volumes (leave blank if not applicable) 48 = 4.8 litre (1.27 gal) fixed flush (WC only) Power Option 42 = 4.2 litre (1.1 gal) fixed flush (WC only)
- Page 2 Transformer (110 to 24 VAC) for 25 Sensor Modules** * Package Quantities May Change. Check the parts section of the latest Delta Commercial Faucet Price List for current quantities. ** Each individual sensor module requires its own 24 VAC to 6 VDC hardwire converter.
- Page 3 Product # + 11mm ( Min. Max. ” All 81T201BT 121mm (4¾”) 54mm (2.13”) 292mm (11½”) 330mm (13”) 121mm (4¾”) 54mm (2.13”) All 81T231BT BEFORE THE FIRST FLUSH (COMPLETE VALVES) FLUSH BOTH OLD AND NEW PIPES: It is important to FLUSH and CLEAN thoroughly both new and old water piping to ELIMINATE contaminants (eg.
- Page 4 INSTALLATION INSTRUCTIONS - BATTERY FLUSHOMETER Step 1: • Install battery flushometer to fixture. • Open inlet stop. Step 2: • Follow instructions on yellow static label (Figure 3). Note: The batteries are already installed and the product is in hibernation mode waiting to be activated.
-
Page 5: Enter Setup Mode
EXIT SETUP MODE ENTER SETUP MODE ALL LIGHTS WILL BE ON, HOLD DOWN TO EXIT SETUP AND RETURN TO THE ELECTRONIC OVERRIDE BUTTON TO ENTER SETUP MODE - HOLD DOWN OPERATION MODE - HOLD DOWN (AGAIN) UNTIL ONLY THE SOLID BLUE ELECTRONIC OVERRIDE BUTTON UNTIL ELECTRONIC OVERRIDE BUTTON LIGHT IS ON, RELEASE TO RETURN... - Page 6 BATTERY STRENGTH INDICATOR & BATTERY REPLACEMENT TO CHECK BATTERY STRENGTH: 1. During Operation Mode - press and hold down the electronic override button for approximately10 seconds. 2. DO NOT RELEASE BUTTON WHEN SOLID BLUE LIGHT IS PRESENT - KEEP HOLDING DOWN. 3.
-
Page 7: Cleaning Instructions
NOTE: DO NOT USE EXCESSIVE FORCE to close the inlet stop stem. We RECOMMEND that the fllushometer be flushed while closing the inlet stop. The noise created by the water flow or the flow into the fixture will stop when the inlet water is shut off. NOTE: Always use DELTA COMMERCIAL GENUINE PARTS to maintain the warranty. EXCESSIVE NOISE: 1. - Page 8 Delta Commercial Faucet Limited Warranty All parts of the Delta® HDF® and TECK® faucets are warranted to the original consumer purchaser to be free from defects in material, finish and workmanship for a period of five (5) years unless otherwise specifically stated in the catalogue and price book. This warranty is made to the original consumer purchaser and shall be effective from date of purchase as shown on purchaser’s receipt.