Yaesu FTDX101MP Information For Customers Operating page 2

FT-891
1. Turn the transceiver OFF.
2. Press and hold in the [ F ] and [ QMB ] buttons while turning
the transceiver ON.
The green LED Indicator will blink with intervals of 0.5 sec
(0.5 sec ON, 0.5 sec OFF).
3. Press and release the [ F ] button, and the Green LED Indica-
tor will now blink with interval of 1 sec (1 sec ON, 1 sec OFF).
4. Press and hold in the [ F ] button, and the radio will re-start
automatically. Once restarted the change of 5 MHz frequency
configuration will have been completed successfully.
FT-991A
1. Turn the transceiver OFF.
2. Press and hold in the [ F ] and [ MODE ] buttons while turning
the transceiver ON.
The green LED Indicator will blink with intervals of 0.5 sec
(0.5 sec ON, 0.5 sec OFF).
3. Press and release the [ MODE ] button, and the Green LED
Indicator will now blink with interval of 1 sec (1 sec ON, 1
sec OFF).
4. Press and hold in the [ MODE ] button, and the radio will re-
start automatically. Once restarted the change of 5 MHz fre-
quency configuration will have been completed successfully.
* The FT-991A is an HF and VHF/UHF transceiver. Please note that the default ARS UHF repeater frequency coverage
and shifts for this model are different from normal UK usage. Selecting the "C2" configuration as below will enable cor-
rect repeater coverage and shifts for UK operation.
ARS Configuration "B2"
Factory Default Setting
ARS Frequency Range: 438.20 MHz - 439.45 MHz ( - shift )
Repeater Shifts:
FT-450D
1. Turn the transceiver OFF.
2. Press and hold in the [ A/B ] button while turning the trans-
ceiver ON.
Setting Number "3" will appear in the display.
3. Rotate the [ MAIN DIAL ] knob and select the Setting Num-
ber "4".
4. Press and hold in the [ MODEp ] button to store the Setting
Number "4" and the radio will re-start automatically. Once
restarted the change of 5 MHz frequency configuration will
have been completed successfully.
5 MHz (60m) 5.351500 MHz - 5.366500 MHz has not
been incorporated into the FT-450D.
By performing the procedure above, the channels
shown in the table are set to USB. These channels ap-
pear between the "last" PMS channel (MEM-P2U) and
the first "regular" memory channel (MEM-001).
Caution:
NOTE: When changing the 5 MHz (60 m) band frequencies according to the procedures above, all saved data, such as
Menu and Memory settings, will be deleted. If you need to change the 5 MHz ( 60 m ) band after using the radio,
make sure to back up your registered data or make a written note, before applying the setting change.
NOTE: The 5 MHz ( 60 m ) band frequency range setting is NOT changed, even when executing the "Full Reset" to re-
store the transceiver to the factory defaults, as described in the Operating Manuals.
7.6 MHz
QMB Button
LED Indicator
Power Switch
ARS Frequency Range: 433.00 MHz - 433.40 MHz ( + shift )
Repeater Shifts:
PHONES
KEY
Power Switch
Important Note
CH No.
UK5-FA 5.260000 MHz
UK5-FB 5.280000 MHz
UK5-FC 5.290000 MHz
UK5-FK 5.368000 MHz
F Button
F Button LED Indicator
MODE Button
ARS Configuration "C2"
Selectable Setting
434.60 MHz - 435.00 MHz ( - shift )
1.6 MHz
Setting Number
MAIN DIAL Knob
MODE Button
Frequency CH No.
UK5-FL
UK5-FE
UK5-FM
-
Power Switch
A/B Button
Frequency
5.373000 MHz
5.400000 MHz
5.405000 MHz
-