Husqvarna AUTOMOWER 435X AWD Operator's Manual page 30

Note:
ECO mode to save energy and avoid
Use
interference with other equipment, for example hearing
loops or garage doors.
Note:
To start the product manually in the work area,
push the STOP button before you remove the product
from the charging station. If not, the product can not be
started in the work area.
To set the ECO mode
1. Select Settings > Operation in the app.
on/off to enable or disable the ECO mode
2. Select
function.
Save .
3. Select
3.12.3 Installation
Installation you can change the installation settings of
In
the product.
3.12.3.1 To find the charging station
The product can be set to search for the charging station
in 3 methods:
Charging station signal
•
Follow boundary wire
•
Follow guide wire
•
The factory setting is set to use the 3 search methods at
the same time. Use the factory setting to find the
charging station as fast as possible and to keep the risk
of tracks on the lawn to a minimum. The product always
Charging station signal . After a
starts to search for the
specified time interval, it also uses
Follow boundary wire .
Causes why the product cannot follow the wire:
• Obstacles near the wire have not been isolated.
• The charging station, the boundary wire or the
guide wire are not installed according to the
To examine where to put the
instructions in
charging station on page 18 , To examine where to
put the boundary wire on page 19 and in To
examine where to put the guide wire on page 22 .
To change the signal range of the charging station
For some installations it is necessary to decrease the
signal of the charging station. For example when the
charging station is put near an obstacle such as a bush
or wall and the signal reaches to the other side of the
obstacle. The product knows that it is close to the
charging station and tries to dock, but the objects
min , avg (average) or max .
prevents it. The options are
30 - Installation
Note:
better to move the charging station, than to decrease the
range of the charging station signal.
1.
2.
3.
To set the delay time for the guide wire and the
boundary wire
1.
2.
3.
4.
3.12.3.2 To do a test of the boundary wire
1.
2.
3.
4.
5.
6.
3.12.3.3 To do a test of the guide wire
1.
Follow guide and
2.
3.
4.
5.
6.
3.12.3.4 Lawn coverage
The product has GPS Assisted Navigation that helps the
product select the most optimal operation.
Use the
manual.
The recommended setting is
Settings > Installation > Find charging
Select
station in the app.
Select signal range.
Select Save .
Settings > Installation > Find charging
Select
station in the app.
on/off to enable or disable to follow the wire.
Select
Move the horizontal bar to set the time delay.
Save .
Select
Installation > Find charging station > Test:
Select
Boundary wire setup.
Put the product 3 m / 9 ft. from the boundary wire,
facing the boundary wire.
Push the START button.
Make sure the product follows the boundary wire to
the charging station.
Make sure the product docks with the charging
station.
Change the position of the charging station or the
boundary wire if the product does not dock with the
To install the charging
charging station. Refer to
station on page 23 and To install the boundary
wire on page 24 .
Select Installation > Find charging station > Test:
Guide 1-3 setup .
Put the product 3 m / 9 ft. from the guide wire,
facing the guide wire.
Push the START button.
Make sure the product follows the guide wire to the
charging station.
Make sure the product docks with the charging
station.
Change the position of the charging station or the
guide wire if the product does not dock with the
To install the charging
charging station. Refer to
station on page 23 and To install the guide wire on
page 24 .
Lawn coverage function to set the settings to
1404 - 006 - 05.01.2021
max . It is usually