Fixtures And Adjustment Equipment List; Fixtures - Sony DNW-A220 Maintenance Manual

1-15. Fixtures and Adjustment Equipment List

1-15. Fixtures and Adjustment Equipment List

1-15-1. Fixtures

n The tools are used only in the maintenance manual Part 2 are also described.
Fig. Part No. Name
1 A-8316-723-A Extension board (EX-617)
A-8321-000-A Extension board (EX-706)
2 A-8317-304-A HN-257 mounted circuit board
3 J-6035-070-A Extruction tool (for PLCC socket)
4 J-6080-840-A Inspection mirror
5 J-6252-520-A Torque screwdriver
(12 kgf.cm) (1.2 N.m) [JB-5252]
J-6325-400-A Torque screwdriver (3 kgf.cm)
6 J-6325-110-A Torque screwdriver bit (for M1.4)
7 J-6325-380-A Torque screwdriver bit (for M2)
8 J-6322-420-A Tape guide adjustment driver (45)
9 J-6323-530-A Stop washer fastening tool
10 J-6323-890-A Torque cassette (FWD BACK TEN.) [MW-389]
11 J-6324-150-A Reel table height adjustment tool [MW-415]
12 J-6326-120-A Hexagon bit (for torque driver)
13 J-6332-240-A VISC phase adjusting tool
14 J-6530-380-A Conversion cable, 6P - 9P
15 J-7032-610-A Cassette reference plate
16 3-184-527-01 Cleaning cloth (15 cmx15 cm)
17 3-649-266-01 Parallel pin (d = 1.6 mm)
3-703-358-04 Parallel pin (d = 2.0 mm)
18 7-432-114-11 Screw locking compound (200g)
19 7-651-000-10 Sony grease SGL-601 (50 g)
7-651-000-11 Sony grease SGL-801 (50 g)
7-651-001-59 Grease PG-662 (20 g)
20 7-661-018-18 Diamond oil NT-68 (50 ml)
21 7-700-751-01 Nut driver (s = 4.5 mm)
22 8-960-075-01 Alignment tape, SR5-1
8-960-075-11 Alignment tape, SR2-1
8-960-075-51 Alignment tape, SR5-1P
8-960-075-61 Alignment tape, SR2-1P
23 8-960-096-01 Alignment tape, CR2-1B
8-960-096-41 Alignment tape, CR5-1B (METAL)
8-960-096-51 Alignment tape, CR2-1B PS
8-960-097-44 Alignment tape, CR5-2A (OXIDE)
8-960-097-45 Alignment tape, CR8-1A (OXIDE)
8-960-096-91 Alignment tape, CR5-1B PS (METAL)
8-960-096-86 Alignment tape, CR8-1B PS (METAL)
8-960-098-44 Alignment tape, CR5-2A PS (OXIDE)
8-960-098-45 Alignment tape, CR8-1A PS (OXIDE)
1-42
For use
Extension of plug-in boards
Extension of plug-in boards
Tape path alignment
Extruction of PLCC IC
Tape curl check
Tightening screws of cabinet
for installing and removing
Tightening screws (for M1.4 and M2 bit)
Tightening screws on mech. deck (l = 75 mm)
Tightening screws on drum, capstan,
reel motor and boards (l = 162 mm)
Tape path adjustment
Installation of stop washer
FWD back tension REV back tension measurement
Reel height check
Tightening screws on mechanical deck for
installing and removing (d = 1.5 mm, l = 85 mm)
VISC alignment for PAL system
Rewrite internal software
Reel height adjustment
Cleaning
Fixing position of cam gear
Fixing position of threading gear/drawing arm
when installing
Inhibits loosening of screws
CTL/AT head height adjustment
Video/audio alignment (for 525/60 system)
Servo alignment (for 525/60 system)
Video/audio alignment (for 625/50 system)
Servo alignment (for 625/50 system)
Tracking alignment (for analog Betacam, NTSC)
Video alignment (for analog Betacam, NTSC)
Tracking alignment (for analog Betacam, PAL)
Betacam video alignment (for analog Betacam, NTSC) P2
Betacam audio alignment (for analog Betacam, NTSC) P2
Video alignment (for analog Betacam, PAL)
Audio alignment (for analog Betacam, PAL)
Video alignment (for analog Betacam, PAL)
Audio alignment (for analog Betacam, PAL)
Description *
P2
P2
P2
P2
P2
P1/P2
P1/P2
P1/P2
P1/P2
P2
P2
P2
P2
P2
P2
P2
P2
P1/P2
P2
P2
P2
P2
P1/P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
P2
DNW-A220
DNW-A220P