Table of Contents
Advertisement
Available languages
Available languages
ENGLISH (
Original Instructions)
•
To charge the battery (5), insert it into the charger (11).
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
•
Plug in the charger and switch on at the mains. The
charging indicator (12) will flash green continuously
(slowly).
The charge is complete when the charging indicator (12)
lights green continuously. The charger and the battery can
be left connected indefinitely with the LED illuminated.
The LED will change to flashing green (charging) state as
the charger occasionally tops up the battery charge. The
charging indica-tor (12) will be lit as long as the battery is
connected to the plugged-in charger.
•
Charge discharged batteries within 1 week. Battery life
will be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
WARNING! Make certain the lock-off button
is engaged to prevent switch actuation before
removing or installing battery
Charger diagnostics
If the charger detects a weak or damaged battery, the
charging indicator (12) will flash red at a fast rate. Proceed
as follows:
•
Re-insert the battery (5).
•
If the charging indicators continues flashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
•
If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
•
If the new battery gives the same indication as the
original battery, take the charger to be tested at an
authorised service centre.
NOTE: It may take as long as 60 minutes to determine
that the battery is defective. If the battery is too hot or
too cold, the LED will alternately blink red, fast and
slow, one flash at each speed and repeat
Selecting the direction of rotation (fig. E)
For tightening, use forward (clockwise) rotation. For
loosening, use reverse (counterclockwise) rotation. To
select forward rotation, push the forward/reverse slider (2)
to the left.
•
To select reverse rotation, push the forward/reverse
slider to the right.
•
To lock the tool, set the forward/reverse slider into the
centre position.
Screwdriving / nut setting
•
Select the appropriate bit / socket for the screw or nut to
be driven.
•
Select forward or reverse rotation as described above.
•
Hold the tool in line with the fastener.
•
After tightening, check torque with a torque wrench.
8
LED work light
The LED work light (7) is activated automatically when the
trig-ger is depressed. The LED work light will illuminate
when the trigger is partially depressed, before the unit
begins running.
State of charge indicator
The tool is fitted with a state of charge indicator. This can
be used to display the current level of charge in the battery
during use.
•
Press the state of charge indicator button (9).
Hints for optimum use
Screwdriving
•
Always use the correct type and size of screwdriver bit.
•
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
•
Always hold the tool and screwdriver bit in a straight line
with the screw
MAINTENANCE
Your Stanley tool has been designed to operate over a long
period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
WARNING! Before performing any maintenance
on the tool, remove the battery from the tool.
Unplug the charger before cleaning it.
•
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
•
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
•
Regularly open the chuck and tap it to remove any dust
from the interior
Optional accessories
WARNING: Since accessories, other than those
offered by STANLEY, have not been tested with
this product, use of such accessories with this
tool could be hazardous. To reduce the risk of
injury, only STANLEY, recommended accessories
should be used with this product. Consult your
dealer for further information on the appropriate
accessories.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY product
needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Make this product
available for separate collection.
STANLEY provides a facility for the collection
and recycling of STANLEY products once they
have reached the end of their working life. To
take advantage of this service please return your
product to any authorised repair agent who will
collect them on our behalf.
Advertisement
Table of Contents
