Chicco Auto-FIX FAST Instructions For Use Manual page 17

ac- indicated by the light blue arrows; pull it
e's as tight as possible (Diag. 13).
in 4. Before attaching the child car seat onto
his the base, check that the stabiliser block
elt. is closed (Diag. 14).
o a 5. Attach the child car seat onto the base
h a (in a rear facing position) and push it
downwards until you hear it click into
ild place (Diag. 15).
6. Check that the child car seat is correctly
not fitted to the base by lifting the front and
to rear sections.
her 7. Pull the diagonal car safety belt and thread
it through the relative slot (O) on the back
of the child car seat backrest (Diag. 16)
or WARNING! When travelling by car, this
es, diagonal safety belt must ALWAYS be
ed threaded through this slot.
8. Pull the belt as tight as possible, without
leaving any slack and making sure it is
E
not twisted.
9. Turn the carry handle to position A check-
ing it rests against the vehicle seat (Diag.
ent 17).
ng WARNING!
he After installing the child car seat, ALWAYS
ps check that the vehicle safety belt is tight-
ened properly along the entire length of
nd the belt and no parts are twisted. NEVER
he fit the car safety belt in any way other than
he that indicated in these instructions.
vis-
kle To remove the child car seat leaving the
base on the vehicle seat:
nd 1. Unthread the diagonal belt through the
he slots in the backrest without removing it
ess from the buckle.
2. Bring the handle bar into a vertical posi-
tion (Diag. 5).
3. Remove the child car seat as illustrated
he above (Diag. 5).
2.3 INSTALLATION WITHOUT THE
ase
BASE
he
to To install the child car seat without the base,
proceed as follows:
cle 1. Fold out the stabiliser block and position
hat the child car seat on the desired vehicle
seat (Diag. 18).
ect 2. Pull the vehicle safety belt and connect
he it to the relative buckle, threading the
(L) horizontal abdominal belt through the
two slots (K) indicated by the light blue
arrows (Diag. 19).
3. Take the diagonal car safety belt and
thread it through the relative slot (O) on
the back of the child car seat backrest
(Diag. 20) WARNING! When travelling by
car, this diagonal safety belt must ALWAYS
be threaded through this slot.
4. Pull the belt as tight as possible, without
leaving any slack and making sure it is
not twisted.
5. Turn the carry handle to position A check-
ing it rests against the vehicle seat (Diag.
21).
To remove the child car seat:
1. Release the car safety belt by pressing
the buckle.
2. Bring the carry handle into a vertical posi-
tion (B).
3. Unthread the belt through the diagonal
and horizontal slots.
2.4 INSTALLATION WITH THE ISOFOX
BASE
(supplied or purchased separately)
For installation with the ISOFIX base, please
refer to the related instructions provided
with the product.
For use with the ISOFIX SEMI-UNIVERSAL
system, it is absolutely necessary to read
the vehicle manual before fitting the child
car seat. The manual will show which cars
seats are compatible with the child car seat
size class.
The Chicco ISOFIX BASE is "SEMI-UNIVERSAL"
approved and is therefore NOT compatible
with all car models, but only with those
specified in the "Approved vehicle list" book-
let provided with the product.
3. OTHER OPERATIONS
3.1 SEATING THE CHILD IN THE CAR
SEAT
1. Raise the fabric flap, whilst pressing the
adjuster button and pull the child car seat
harness straps to loosen them (Diag. 22).
2. Press the red button to open the buckle
and release the harness straps (Diag. 23).
3. Sit the baby inside.
17