Sony XAV-AX200 Service Manual page 14

XAV-AX200/AX200C2
(AEP, UK)
Monitor connection
When installing a monitor for the rear seat, connect
its parking brake switch cord to the ground (earth).
Power connection diagram
Check your car's auxiliary power connector and
match the connections of cords correctly
depending on the car.
Auxiliary power connector
Common connection
Red Red
Yellow Yellow
continuous power
12 Yellow
supply
15 switched power supply Red
When the positions of the red and yellow
leads are inverted
Red Red
Yellow Yellow
12 switched power supply Yellow
continuous power
15 Red
supply
For cars without ACC position
Red
Red
Yellow Yellow
After matching the connections and switching
power supply leads correctly, connect the unit to
the car's power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
Installing the microphone
To capture your voice during handsfree calling, you
need to install the microphone .
Clip (not supplied)
14
Cautions
• It is extremely dangerous if the cord becomes
wound around the steering column or gearstick.
Be sure to keep it and other parts from interfering
with your driving operations.
• If airbags or any other shock-absorbing
equipment are in your car, contact the store where
you purchased this unit or the car dealer before
installation.
Note
Before attaching the double-sided tape
surface of the dashboard with a dry cloth.
Using the wired remote control
When using the steering wheel remote
control
Installation of the connection cable RC-SR1 (not
supplied) is required before use.
1
To enable the steering wheel remote control, select
[General Settings] [Steering Control Custom] to
.
make the registration (page 14).
When the registration is complete, the steering
wheel remote control becomes available.
Notes on installing the connection cable RC-SR1 (not
supplied)
• Refer to the support site on the back cover for details then
connect each lead properly to the appropriate leads.
Making an improper connection may damage the unit.
• Consulting the dealer or an experienced technician for
help is recommended.
When using the wired remote control
1
To enable the wired remote control, set [Steering
Control] in [General Settings] to [Preset] (page 14).
Using the rear view camera
Installation of the rear view camera (not supplied) is
required before use.
The picture from a rear view camera connected to
the CAMERA IN (REAR) terminal is displayed when:
the back lamp of your car lights up (or the shift
lever is set to the R (reverse) position).
you press HOME, touch [Camera], then touch
[Rear].
Installation
Mounting the unit in the dashboard
• Before installing, make sure the catches on both
sides of the bracket are bent inwards 3.5 mm
( 5 / in).
32
• For Japanese cars, see "Mounting the unit in a
.
Japanese car" (page 30).
1
Position the bracket inside the
dashboard, then bend the claws outward
for a tight fit.
Catch
Larger than
111 mm (4 3 / in)
8
2
Mount the unit onto the bracket
, clean the
Notes
• If the catches are straight or bent outwards, the unit will
not be installed securely and may spring out.
• Make sure the 4 catches on the protection collar
properly engaged in the slots of the unit.
Mounting the unit in a Japanese car
You may not be able to install this unit in some
Japanese cars. In such a case, consult your Sony
dealer.
Bracket
.
Parts supplied with
your car
When mounting this unit to the preinstalled
brackets of your car, use the supplied screws
the appropriate screw holes based on your car:
T for TOYOTA and N for NISSAN.
Note
To prevent a malfunction, install only with the supplied
screws .
Fuse replacement
When replacing the fuse, be sure to
use one matching the amperage
rating stated on the original fuse.
If the fuse blows, check the power
connection and replace the fuse.
If the fuse blows again after
replacement, there may be an
internal malfunction. In such a case, consult your
nearest Sony dealer.
Larger than
182 mm (7 1 / in)
4
.
are
To the dashboard/center console
Bracket
in
Fuse (10 A)
SYS SET