Sony XAV-AX200 Service Manual page 13

(AEP, UK)
Connection/Installation
Cautions
• Run all ground (earth) leads to a common
ground (earth) point.
• Do not get the leads trapped under a screw or
caught in moving parts (e.g., seat railing).
• Before making connections, turn the car ignition
off to avoid short circuits.
• Connect the power supply lead
speakers before connecting it to the auxiliary
power connector.
• Be sure to insulate any loose unconnected leads
with electrical tape for safety.
Precautions
• Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
• Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature, such
as in direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other stereo
components, the amperage rating of the car circuit to which
the unit is connected must be higher than the sum of each
component's fuse amperage rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
*1 Not supplied
*2 Speaker impedance: 4 Ω – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a wired
remote control (not supplied).
For details on using the wired remote control, see "Using
.
the wired remote control" (page 29).
*5 Whether in use or not, route the microphone input cord
so it does not interfere with driving operations. Secure
the cord with a clamp, etc., if it is installed around your
feet.
*6 For details on installing the microphone, see "Installing
.
the microphone" (page 29).
*7 To connect a smartphone to the main unit, an
appropriate cable (not supplied) is required.
*8 To connect an iPhone, use the USB connection cable for
iPhone (not supplied).
*9
*10 For the navigation module XA-NV400 (not supplied)
Making connections
If you have a power antenna (aerial) without a relay
box, connecting this unit with the supplied power
supply connection cable may damage the
antenna (aerial).
To the car's speaker connector
1 Purple
Rear speaker
Purple/black
(right)
2
striped
3 Gray
Front speaker
(right)
4 Gray/black striped
5 White
Front speaker
White/black
(left)
6
striped
7 Green
Rear speaker
Green/black
(left)
8
striped
Connection
to the unit and
To the car's power connector
continuous power
12
supply
power antenna (aerial) /
13 power amplifier control
(REM OUT)
switched illumination
14
power supply
15 switched power supply
16 ground (earth)
To the parking brake switch cord
The mounting position of the parking brake
switch cord depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply connection cable
to the parking brake switch cord.
* 2
See "Power connection diagram"
(page 29) for details. for details.
Light green
Purple/white striped
Hand brake type
Yellow
To the +12 V power terminal of the car's rear
lamp lead (only when connecting the rear
Blue/white striped
view camera)
Orange/white
Memory hold connection
striped
When the yellow power supply lead is connected,
Red
power will always be supplied to the memory
Black
circuit even when the ignition switch is turned off.
Speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 Ω to 8 Ω and
with adequate power handling capacities to avoid
damage.
XAV-AX200/AX200C2
Subwoofer*
* 3
* 3
* 3
Power amplifier* 1
* 3
Monitor* 1
* 3
Camera*
* 3
Camera*
* 3 Rear view
camera*
Smartphone* 7 , iPhone*
USB device
* 9
from a wired remote control (not
supplied) *4
For details, see "Making
.
connections" (page 28).
from a car antenna (aerial)
Parking brake switch cord
Foot brake type
1
1
1
1
8 ,
* 5 * 6
13
SYS SET