Sharp SD-2060 Operation Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Copier
  5. SD-2060
  6. Operation manual
Sharp SD-2060 Operation Manual

Sharp SD-2060 Operation Manual

Electrostatic copying machine
Hide thumbs Also See for SD-2060:
Table of Contents

Advertisement

Quick Links

Download this manual
Downloaded from:
http://www.usersmanualguide.com/
MODEL
SD-2060
ELECTROSTATIC
COPYING MACHINE
OPERATION MANUAL
• GETTING STARTED
• MAKING COPIES
• SUPPLIES
• COPIER TROUBLE?
• GENERAL INFORMATION
• OPTIONAL EQUIPMENT
Page
2
10
48
53
67
70

Advertisement

Table of Contents
loading

Related Manuals for Sharp SD-2060

Summary of Contents for Sharp SD-2060

  • Page 1 MODEL SD-2060 ELECTROSTATIC COPYING MACHINE OPERATION MANUAL Page • GETTING STARTED • MAKING COPIES • SUPPLIES • COPIER TROUBLE? • GENERAL INFORMATION • OPTIONAL EQUIPMENT Downloaded from: http://www.usersmanualguide.com/...
  • Page 2 Downloaded from: http://www.usersmanualguide.com/...

  • Page 3: Table Of Contents

    CONTENTS Page GETTING STARTED INTRODUCTION ......2 USING THIS MANUAL ......2 INSTALLATION REQUIREMENTS ....3 CAUTIONS ......... 3 PART LOCATIONS AND FUNCTIONS ..... 4 Exterior ........4 Interior ........5 Operation Panel ......6 POWER ON AND OFF ......8 INFORMATION FUNCTION ....

  • Page 4: Introduction

    The SD-2060 was also designed with ease of use in mind. The easy- to-understand operation panel and INFORMATION function will guide the user through most operations. However, to gain the maxi-...

  • Page 5: Installation Requirements

    INSTALLATION REQUIREMENTS To ensure safety and proper machine performance, please note the following before initial installation and whenever the machine is to be relocated. The copier should be installed near an accessible power outlet for easy disconnection. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

  • Page 6: Part Locations And Functions

    PART LOCATIONS AND FUNCTIONS Exterior !4 !5 !7 !8 q Exit tray (optional) !0 Original guides Finished copies are deposited here. Adjust to the size of the original. w Paper clip tray !1 Power switch Place paper clips here. Press to turn copier power on and off. e Operation panel !2 RADF tray Contains all operation keys and indicators.

  • Page 7: Interior

    PART LOCATIONS AND FUNCTIONS Interior @5 Toner collecting container cover 11"R, 8-1/2" x 14", 11" x 17", or A4 size paper.) Tray capacity is 1,000 sheets of 80 g/m (20 lb.) Open to replace used toner collecting container. paper. (Detailed description on page 51.) * Can be selected in certain areas.

  • Page 8: Operation Panel

    PART LOCATIONS AND FUNCTIONS Operation Panel SORTER ORIGINAL TO COPY AUTO IMAGE READY TO COPY ORIGINALS ) REDUCTION ENLARGEMENT EVEN NUMBER 100% ODD NUMBER SORT COPY RATIO GROUP AUTO SELECT 100% ZOOM 1. A4 EXPOSURE PRE-COUNT EXPOSURE STAPLE AUTO ORIGINAL AUTO MANUAL SORT...
  • Page 9 PART LOCATIONS AND FUNCTIONS COPIES SELECTED COPIES MADE SCROLL DISPLAY SPECIAL MODES Inch system INFORMATION MARGIN SHIFT DUAL PAGE COPY PROGRAM 8 / x11 CLEAR ALL AUTO SELECT ERASE COVERS INSERTS START 1. 8 / x11 TRANSPARENCY 8 / x11R INTERRUPT CHANGE INSERTS...

  • Page 10: Power On And Off

    POWER ON AND OFF The power switch is located on the right side of the copier. When the power switch is turned to the “ON” position, the message “WARMING UP, PLEASE WAIT.” will appear in the message display. Warming up takes about 5 minutes. Once the copier is ready, the message display will change to “READY TO COPY.”, and the START key indicator will light up, indicating that copying is possible.

  • Page 11: Information Function

    INFORMATION FUNCTION The information feature provides a quick reference guide to the use of the various features and functions of this copier. The information mode can be entered when the copier is in the standby condition. The symbol ( ) may appear at the end of a message indicating that the SCROLL DISPLAY key should be pressed to display additional information.

  • Page 12: Audit Accounts

    AUDIT ACCOUNTS If this copier has been programmed in the audit account mode, it will not function until an assigned 5-digit account number has been entered. KEY OPERATOR See page 6 of the KEY OPERATOR’S GUIDE for setting the auditing mode. The initial status of the message display will be <A001>...

  • Page 13: Using The Radf

    USING THE RADF The RADF (Reversing Automatic Document Feeder) Special originals such as transparency film and will handle A5 to A3 (8-1/2" x 5-1/2" to 11" x 17") size tracing paper should not be fed from the RADF, but originals. should be placed on the document glass.
  • Page 14 USING THE RADF W / W Ensure that is selected on the ORIGINAL TO ORIGINAL TO COPY COPY section of the operation panel. PRE-COUNT ORIGINALS ) ORIGINAL EVEN NUMBER Use the 10-key pad to enter the desired number of cop- COPIES SELECTED COPIES MADE ies.
  • Page 15 USING THE RADF If the number of originals is known, use the ORIGINAL TO COPY key to select EVEN NUMBER or ODD EVEN NUMBER ORIGINALS ) ODD NUMBER NUMBER on the ORIGINAL TO COPY section of the EVEN NUMBER operation panel, then proceed to step 3. If the number ODD NUMBER of originals is not known, select PRE-COUNT ORIGINAL for an automatic count by the RADF and...
  • Page 16 USING THE RADF Enter the desired number of copies. If the specified number of copies is more than 50, the COPIES SELECTED display will display 50 after starting copying. If an optional sorter is installed, the display will change to 20 after START copying starts.

  • Page 17: Copying From The Document Glass

    COPYING FROM THE DOCUMENT GLASS Use the document glass for copying single originals, bound documents, and other originals that cannot be set on the RADF. 2-sided to 2-sided or 2-sided to 1-sided cannot be selected when copying from the document glass. These operations, however, can be performed by manually turning over the originals.
  • Page 18 COPYING FROM THE DOCUMENT GLASS 2-sided copies from 1-sided originals For an odd number of originals: Set the last page of the document onto the document glass and copy it in the 1-sided to 1-sided mode. Use the ORIGINAL TO COPY key to select EVEN EVEN NUMBER NUMBER.

  • Page 19: Reduction/Enlargement/Zoom

    REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the REDUCTION key, ENLARGEMENT key, or ZOOM keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. KEY OPERATOR A total of four extra presets, two each for reduction and enlargement, can be added.
  • Page 20 REDUCTION/ENLARGEMENT/ZOOM Manual selection Set the original(s) in the RADF tray or on the document glass. Use the REDUCTION, ENLARGEMENT and ZOOM keys to set the desired copy ratio. Preset reduction ratios are: 86%, 81%, 70%, and 50% (95%, 77%, 64% and 50%). Preset enlargement ratios are: 115%, 122%, 141%, and 200% (121%, 129%, 141%, and 200%).

  • Page 21: Special Papers (Manual Feed)

    Insert the copy paper all the way into the bypass tray. Labels, tracing paper, and special purpose papers other than SHARP standard transparency film must be fed individually. Up to 100 sheets of standard copy paper measuring from A5 to A3 (8-1/2"...

  • Page 22: Exposure Adjustments

    EXPOSURE ADJUSTMENTS This copier has three selectable exposure modes –– AUTOMATIC, MANUAL, and PHOTO mode. Automatic 100% This is the standard initial setting for this copier. In this mode, the EXPOSURE characteristics of an original being copied are “read” by the exposure system, and exposure adjustments are made automatically.

  • Page 23: Dual Page Copying

    DUAL PAGE COPYING The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the document glass. It is especially useful when copying books and other bound documents and can be used with the MARGIN SHIFT feature. Place the originals on the document glass with the centre of the two pages aligned with the paper size index A4...

  • Page 24: Erase

    ERASE This copier has an edge erase function and a centre erase function. Edge erase can be used to eliminate shadow lines around the edges of copies caused when thick paper or a book is used as an original. Centre erase can be used to eliminate the shadow produced by the bindings of bound documents.

  • Page 25: Margin Shift

    MARGIN SHIFT The MARGIN SHIFT feature automatically shifts the text or image to the right both on one-sided copies and on the front of two-sided copies. The images are shifted to the left on the second side of two- sided copies. The standard shift setting is 9 mm (1/4"), but can be changed to 0 mm, 3 mm, 6 mm, 12 mm, or 15 mm (0", 1/8", 3/8", 1/2", or 5/8") as desired.
  • Page 26 MARGIN SHIFT Margin shift adjustment Press the MARGIN SHIFT key. DUAL PAGE COPY MARGIN SHIFT ERASE COVERS INSERTS Press the CHANGE key. The following message will appear. TRANSPARENCY <M082> INSERTS CHANGE SIDE 1 SIDE 2 SELECT MARGIN SHIFT AND DIRECTION BY 10–KEY PAD.

  • Page 27: Covers

    COVERS The COVERS mode is used to place covers on the front, back, or both the front and back of multipage documents. Front cover sheets can be copied on, but only on the front side even in the 1-sided to 2-sided and 2-sided to 2-sided copy modes. The back side of the original designated as the cover will not be copied.
  • Page 28 COVERS Press key 1 on the 10-key pad. The following message will appear. <M008> USE 10–KEY PAD TO SELECT COVER PLACEMENT. CLEAR/STOP AUDIT FRONT BACK FRONT+BACK CLEAR : PUSH 1 : PUSH 2 : PUSH 3 Select cover placement by pressing key 1, 2, or 3 on the 10-key pad.

  • Page 29: Inserts

    INSERTS The INSERTS mode is used to insert Insert sheets can be fed from tray 2, tray 3, or the bypass tray, but sheets as chapter dividers. when the bypass tray is used for cover stock, insert sheets must be fed from tray 2 or tray 3. If the same paper stock is to be used for the cover stock and the insert sheets, the bypass tray may be used for both.
  • Page 30 INSERTS To place insert sheets with printing in the 1-sided copy mode Make note of the numerical positions of the original INSERTS WITH pages which are to be copied onto insert sheets. In the PRINTING example to the left, these are positions 3 and 6. Place the originals face down in the RADF tray and press the COVERS/INSERTS key.
  • Page 31 INSERTS Enter the number of originals using the 10-key pad and then press the PROGRAM key. If the number of originals is not known, press only the PROGRAM key. If only the PROGRAM key is pressed, the number of originals PROGRAM will be counted.
  • Page 32 INSERTS Enter the remaining positions as in step 7 and then press the PROGRAM key again to end the sequence. INFORMATION PROGRAM Enter page numbers in ascending order. To correct an entry error, press the SCROLL DISPLAY key. CLEAR ALL The following message will appear.
  • Page 33 INSERTS To place insert sheets without printing in the 1-sided copy mode Make note of the numerical positions of originals INSERTS WITHOUT which are to follow blank insert sheets. In the example PRINTING to the left, these are positions 3 and 5. Place the originals face down in the RADF tray and press the COVERS/INSERTS key.
  • Page 34 INSERTS Enter the number of originals using the 10-key pad and then press the PROGRAM key. If the number of originals is not known, press only the PROGRAM key. If only the PROGRAM key is pressed, the number of originals PROGRAM will be counted.
  • Page 35 INSERTS Enter the remaining positions as in step 7 and then press the PROGRAM key again to end the sequence. INFORMATION PROGRAM Enter page numbers in ascending order. To correct an entry error, press the SCROLL DISPLAY key. CLEAR ALL The following message will appear.
  • Page 36 INSERTS To place insert sheets with printing in the 2-sided copy mode Separate the document into chapters and count the number of pages in each chapter. If a chapter of 1- sided originals contains an odd number of pages, make it even by adding a blank sheet at the end. Make note of the numerical positions of the original pages which are to be copied onto insert sheets.
  • Page 37 INSERTS Press key 2 on the 10-key pad. The following message will appear. <M116> PLEASE INPUT THE NUMBER OF ORIGINALS THEN PRESS THE P KEY. PRESS THE P KEY FOR AUTO-COUNT. CLEAR/STOP AUDIT CLEAR Enter the number of originals using the 10-key pad and then press the PROGRAM key.
  • Page 38 INSERTS Use the 10-key pad to designate the first original position to be copied onto an insert sheet and then press the PROGRAM key. In this example, press key 5 and then the PROGRAM key. PROGRAM The entered number will be displayed on the bottom line of the message display.
  • Page 39 INSERTS To place insert sheets without printing in the 2-sided copy mode Separate the document into chapters and count the number of pages in each chapter. If a chapter of 1- sided originals contains an odd number of pages, make it even by adding a blank sheet at the end. Make note of the numerical positions of the pages which are to follow blank insert sheets.
  • Page 40 INSERTS Enter the number of originals using the 10-key pad and then press the PROGRAM key. If the number of originals is not known, press only the PROGRAM key. If only the PROGRAM key is pressed, the number of originals PROGRAM will be counted.
  • Page 41 INSERTS Enter the remaining positions as in step 8 and then press the PROGRAM key again to end the sequence. INFORMATION Enter page numbers in ascending order. PROGRAM To correct an entry error, press the SCROLL DISPLAY key. CLEAR ALL The following message will appear.
  • Page 42 INSERTS To place covers and insert sheets Make note of the numerical positions of the pages which are to be copied onto insert sheets, or to follow blank insert sheets, and place the originals face down in the RADF tray. Press the COVERS/INSERTS key.
  • Page 43 INSERTS Enter the number of originals using the 10-key pad and then press the PROGRAM key. If the number of originals is not known, press only the PROGRAM key. If only the PROGRAM key is pressed, the number of originals PROGRAM will be counted.
  • Page 44 INSERTS Examples of positions to be designated for insert sheets in the COVERS/INSERTS mode MODE INSERTS OUTPUT 1-sided copy mode Front cover with printing 3, 6 Insert sheets with printing Front cover without printing 3, 6 Insert sheets with printing Front cover with printing 3, 5 Insert sheets without printing...

  • Page 45: Transparency Film With Insert Sheets

    TRANSPARENCY FILM WITH INSERT SHEETS When copying onto transparency film, insert sheets can be placed following each transparent sheet. The insert sheets can be pro- cessed blank or can be copied with the same image as the transpar- ent sheets. This mode can be selected only in the 1-sided to 1-sided and 2- sided to 1-sided modes.
  • Page 46 TRANSPARENCY FILM WITH INSERT SHEETS Press key 1 or key 2 on the 10-key pad. CLEAR/STOP AUDIT CLEAR Load transparency film into the bypass tray. Use the TRAY SELECT key to select a paper tray with the same size paper as the transparencies. The copy paper must be the same size as the transparency film.

  • Page 47: Job Memory

    JOB MEMORY Frequently used job programs can be stored in one of the nine storage registers. This is convenient for quick job recall without losing time manually reprogramming each aspect of the job. Settings for the following functions can be stored in job memory: original to copy mode, reduction/enlargement/zoom, exposure adjustments, erase, margin shift, dual page copying, covers/ inserts, transparency inserts, tray select, and sort/staple sort...
  • Page 48 JOB MEMORY Deleting a stored job program Follow steps 1 and 2 in “Storing a job program.” (1. Press the PROGRAM key. 2. Press the 0 key.) Press key 2 on the 10-key pad. The following message will appear. CLEAR/STOP <P005>...

  • Page 49: Interrupt

    INTERRUPT INTERRUPT can be used to temporarily stop a long copy run so that a short job can be run. Duplex copying, sort, group, staple sort, covers/inserts, and transparency inserts cannot be selected during interrupt copying. Also job program recall cannot be selected. Reduction/enlargement/zoom, exposure adjustments, dual page copying, erase, and margin shift can be selected during interrupt copying.

  • Page 50: Paper

    11" x 17", A4) parency film, labels For best results, use only paper recommended by SHARP. Labels must be set face up in the bypass tray. Do not use 8-1/2" x 11"R (A4R) paper in any tray because it will be regarded as A4R (8-1/2"...
  • Page 51 PAPER Load it onto the feed table. Be sure to load paper appropriate for paper tray 1. See the table above. Do not exceed the maximum height line. Push the paper tray back into the copier. The release button lamp will blink as the feed table returns to the feed position and will light steadily when it is in position to feed.

  • Page 52: Adding Toner

    “TONER SUPPLY IS LOW” appears. To add ton- er, stop the copier and proceed as below. For best copying results, be sure to use only SHARP products. NOTE: During long copy runs of multiple dark originals, “TONER REPLEN- ISHMENT IN PROGRESS”...

  • Page 53: Used Toner Disposal

    Use the cap on the side of the full container to cap it. Keep the full toner collecting container until the next regular service call. Your authorised Sharp Service Technician will collect the container for disposal. Install a new toner collecting container by pushing it down onto the tray, tilting it in and then allowing it to move upward engaging it with the copier.

  • Page 54: Storage Of Supplies

    STORAGE OF SUPPLIES Standard SD-2060 supplies replaced by the user include copy pa- per, toner and staple cartridges for the optional staple sorter. For best copying results, be sure to use only SHARP products. The SD-2060 Copier/Duplicator has advanced process control tech- nology which improves copy quality uniformity.

  • Page 55: Misfeed Removal

    MISFEED REMOVAL When a misfeed occurs, the copier will stop. If paper becomes accidentally torn during removal, The message “OPEN THE COPIER DOORS AND be sure to remove all pieces. Be careful not to damage the photoconductive drum REMOVE PAPER AS INDICATED. PRESS FOR RECOVERY INSTRUCTIONS.”...
  • Page 56 MISFEED REMOVAL Location A Open the exit roller cover and gently pull out the original. Location B Open the RADF cover. Remove any sheets in this area. Then close the RADF cover. If the original is not easily removed, open the exit roller cover to pull out the original.
  • Page 57 MISFEED REMOVAL OPEN THE COPIER DOORS AND REMOVE PAPER AS INDICATED. PRESS KEY FOR RECOVERY INSTRUCTIONS. Misfeed in the paper trays When the release button lamp goes out, pull out the paper tray (T1, T2 or T3). Do not pull out the paper tray before the release button lamp goes out.
  • Page 58 MISFEED REMOVAL OPEN THE COPIER DOORS AND REMOVE PAPER AS INDICATED. PRESS KEY FOR RECOVERY INSTRUCTIONS. Misfeed in the bypass tray Pull out the misfed paper while pressing the misfeed Misfeed release button release button for manual feed. Open the right front door of the copier and then close Confirm that the misfeed display is cleared.
  • Page 59 MISFEED REMOVAL Turn transport lever (E) in the direction of the arrow. Turn roller rotating knob (D) in the direction of the arrow to remove misfed paper. If the misfed paper cannot be removed by turning knob (D) alone, turn knobs (D) and (C) together. CAUTION Be careful not to damage the photoconductive drum or the co- rona wires.
  • Page 60 MISFEED REMOVAL Open paper guide (B) and remove any misfed paper. Push the paper transport back securely into the copier. Turn transport lever (E) back in the direction of the arrow. Close the front doors. Confirm that the misfeed display is cleared. Downloaded from: http://www.usersmanualguide.com/...
  • Page 61 MISFEED REMOVAL OPEN THE COPIER DOORS AND REMOVE PAPER AS INDICATED. PRESS KEY FOR RECOVERY INSTRUCTIONS. Misfeed in the fusing area Open the front doors of the copier. Turn transport lever (E) in the direction of the arrow. Turn roller rotating knob (G) in the direction of the Roller rotating knob (G) arrow while pulling this knob and remove any misfed paper from the fusing area.
  • Page 62 MISFEED REMOVAL Turn roller rotating knob (G) in the direction of the Roller rotating knob (G) arrow to remove any misfed paper. Open the paper guide as shown and turn roller rotating Paper guide Roller rotating knob (G) knob (G) in the direction of the arrow to remove any misfed paper.
  • Page 63 MISFEED REMOVAL <J001> OPEN THE COPIER DOORS AND REMOVE PAPER AS INDICATED. PRESS KEY FOR RECOVERY INSTRUCTIONS. Misfeed in the duplex transport section and duplex tray Open the side door at the left side of the copier. If an optional sorter is installed, slide it away from the copier to allow access to the door.
  • Page 64 MISFEED REMOVAL Pull out the paper transport by holding transport lever (E). Open paper guide (J) after opening paper guide (I). (J) (I) Slide paper guide (K) in the direction of the arrow. Open paper guide (K) and remove any misfed paper. Close paper guide (K) and then close paper guides (I) and (J) after removing misfed paper.
  • Page 65 MISFEED REMOVAL Remove any misfed paper on the duplex tray. Duplex tray Push the paper transport back securely into the copier after checking that paper guides (I) and (J) are closed. (J) (I) Turn transport lever (E) back in the direction of the arrow.
  • Page 66 MISFEED REMOVAL OPEN THE COPIER DOORS AND REMOVE PAPER AS INDICATED. PRESS KEY FOR RECOVERY INSTRUCTIONS. Misfeed in the exit area Remove any misfed paper gently while lifting up the Exit area guide exit area guide. Remove the exit tray if necessary. If an optional sorter is installed, slide it away from the copier.

  • Page 67: Troubleshooting

    TROUBLESHOOTING Always check the message display whenever the copier stops or operation is not possible. The messages will give you easy-to- follow directions. If the messages do not give specific instruc- tions, check the list below. Problem Solution Copier plugged in? Plug the copier into a grounded outlet.
  • Page 68 Clean regularly. See next page. copies. transport belt dirty? If a problem persists after checking the above, please consult your key operator prior to contacting your authorised Sharp Service Cen- tre. Self-diagnostic function An automatic self-diagnostic function is built into this copier. Should the copier malfunction, the self-diagnostic function will locate the problem and stop the copier to prevent damage.

  • Page 69: User Maintenance

    USER MAINTENANCE The document glass and RADF transport belt must be kept clean to avoid dirty areas from being copied onto the copies. Document glass and RADF transport belt Wipe the document glass and transport belt with a soft, clean cloth. If necessary, dampen the cloth with water.

  • Page 70: Specifications

    SPECIFICATIONS COPIER Type Console Copy system Dry, electrostatic transfer system Originals Sheets, bound documents Original size Max. A3 (11" x 17") Copy sizes Max. A3 (11" x 17"), min. A5 (8-1/2" x 5-1/2") 60 copies/min. (A4, (8-1/2" x 11")) Copying speed 45 copies/min.

  • Page 71: Optional Equipment

    SPECIFICATIONS Local voltage ±10% Required power supply Power consumption Max. 1.9 kW Overall dimensions 1627 (W) x 731 (D) mm (64-1/16" (W) x 28-25/32" (D)) Weight Approx. 239 kg (527 lbs.) Copier dimensions 1167 (W) x 731 (D) x 1038 (H) mm (45-61/64"...

  • Page 72: System Configuration

    SYSTEM CONFIGURATION The options which are available for the SD-2060 are shown below. 20-bin sorter (SF-S16) Exit tray (Option) 20-bin staple sorter (SF-S53) COPY CARD Counter commander (SF-EA13) Card counter (SF-EA11) NOTE: Operating instructions follow for the Sorters (SF-S16 and SF- S53).

  • Page 73: 20-Bin Sorter (Sf-S16)/20-Bin Staple Sorter (Sf-S53)

    20-BIN SORTER (SF-S16) 20-BIN STAPLE SORTER (SF-S53) The SF-S16 20-Bin Sorter has two sorter modes for different copying jobs: one sorts by sets of originals and the second groups by origi- nal. The SF-S53 20-Bin Staple Sorter has, in addition to the above two modes, a STAPLE SORT mode.

  • Page 74: Using A Sorter

    20-BIN SORTER(SF-S16)/20-BIN STAPLE SORTER(SF-S53) Using a sorter SORT GROUP Press the SORT/GROUP key to select the desired mode. (The STAPLE SORT mode cannot be selected for the SF-S16.) To cancel the mode, press the SORT/GROUP key until the indicator goes off. NON-SORT ODD NUMBER SORT...

  • Page 75: Sorter Capacities

    20-BIN SORTER(SF-S16)/20-BIN STAPLE SORTER(SF-S53) SORTER CAPACITIES SF-S16 SF-S53 Top bin Non-sort bin 100 sheets in the NON-SORT mode 250 sheets in the NON-SORT mode Sort bins Sort bins Sort/Staple Sort Mode: Up to 50 per bin in the SORT mode Paper size Bin capacity Up to 30 per bin in the GROUP mode...

  • Page 76: Staple Sort (Sf-S53 Only)

    20-BIN STAPLE SORTER(SF-S53) STAPLE SORT (SF-S53 only) The STAPLE SORT mode automatically staples copies of A4, A4R, B4, A3, 8-1/2" x 11", and 8-1/2" x 14" (8-1/2" x 11", 8-1/2" x 11"R, 8- 1/2" x 14", 11" x 17", and A4) sizes. For other paper sizes, use the manual stapling mode.
  • Page 77 20-BIN STAPLE SORTER(SF-S53) Using the Document Glass Set the original on the document glass with the corner to be stapled to the upper right. Stapling location If the number of copies to be made is more than 50 for A4, A4R, or 8-1/2"...

  • Page 78: Manual Stapling

    20-BIN STAPLE SORTER(SF-S53) Manual stapling To use the stapling feature only, without using the STAPLE SORT mode, follow the procedure below. Align the edges of the copies to be stapled. Place the set of copies into the bin below the non-sort bin, making sure the edges are flush with the inner Copies right corner, as shown in the figure.

  • Page 79: Staple Cartridge Replacement

    If it is not stapled, press the manual staple key again. If the stapler does not operate properly even after replace- ment, a staple may be jammed in it. See the next page. Staples for the staple sorter are available from your Sharp dealer. Downloaded from:...

  • Page 80: Staple Jam Removal

    20-BIN STAPLE SORTER(SF-S53) Staple jam removal “REMOVE STAPLER AND CHECK IT.” will be displayed as a key operator assistance call if staples become jammed in the stapler of optional staple sorter SF-S53. Remove the jammed staples follow- ing the instructions of your key operator. Turn off the copier and open the stapler cover.
  • Page 81 20-BIN STAPLE SORTER(SF-S53) Use the tool attached to the inside of the stapler cover to remove jammed staples as shown. Return the green lever on the face of the stapler back Green release Green lever down into place. lever Return the green release lever on top of the stapler unit to its upright position.

  • Page 82: Misfeed Removal

    20-BIN SORTER(SF-S16) Misfeed removal The copier will stop when a misfeed occurs. The message “OPEN THE COPIER DOORS AND REMOVE PAPER AS INDICATED. PRESS KEY FOR RECOVERY INSTRUC- TIONS.” will appear with a display of paper misfeed locations. Press the INFORMATION and SCROLL DISPLAY keys for more detailed information as necessary.
  • Page 83 20-BIN STAPLE SORTER(SF-S53) SF-S53 20-Bin Staple Sorter While holding the sorter release lever, carefully pull the staple sorter away from the copier. Open the paper guide. Remove the misfed paper and return the paper guide to its original position. While holding the sorter release lever, push the staple sorter toward the copier and latch it into place.

  • Page 84: Specifications

    20-BIN SORTER(SF-S16)/20-BIN STAPLE SORTER(SF-S53) Specifications SF-S16 No. of bins Bin capacity NON-SORT: 100 sheets (top bin) SORT: 50 sheets GROUP: 30 sheets Paper size Top bin: Max. A3 (11" x 17") Min. A5 (8-1/2" x 5-1/2") Sort bin: Max. A3 (11" x 17") Min.
  • Page 85 Downloaded from: http://www.usersmanualguide.com/...
  • Page 86 SD-2060 SHARP CORPORATION PRINTED IN JAPAN Downloaded from: http://www.usersmanualguide.com/...
  • Page 87 This file has been downloaded from: www.UsersManualGuide.com User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes.. Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide, manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product, documentation manual, user maintenance, brochure, user reference, pdf manual Downloaded from:...

Table of Contents