Dimensions And Clearances; Utilities Entry Data - York Sunline 2000 Installation Instruction

511.06-N5Y
(Direct-Drive Units)
FIELD-SUPPLIED
DISCONNECT SWITCH
LOCATION
CONTROL
FILTER ACCESS
BOX ACCESS
5
32
8
3
" PVC FEMALE
4
7
44
COND. DRAIN
8
(See Detail "A")
A, B
WIRING ENTRY
(See Detail "B")
3
5
8
7
7
8
BOTTOM SUPPLY &
RETURN AIR OPENINGS
(SEE NOTE)
B - POWER WIRING ENTRY
A - CONTROL WIRING ENTRY
CLEARANCES
Front
Back
Left Side
(Filter Access)
Right Side (OD Coil)
1
Below Unit
2
Above Unit
NOTE:
Units and ductwork are approved for zero clearance to combustible
materials when equipped with electric heaters.
1 Units may be installed on combustible floors made from wood or
class A, B or C roof covering material. (Applicable in USA only).
2 Units must be installed oudoors. Overhanging structures or shrubs
should not obstruct the outdoor coil nor the fan outlet.
1
27
2
1
19
2
DETAIL "A"
UNIT WITH ECONOMIZER RAIN HOOD
FIG. 6 - DIMENSIONS & CLEARANCES - 3, 4 & 5 TONS
8
BLOWER
ACCESS
FRONT VIEW
1
82
1
11
2
1
17
2
1
6
2
1
17
3
2
6
4
1
8
8
UNIT BASE WITH RAILS
Shown separately to illustrate bottom
duct openings and power connection
locations.
NOTE: For curb-mounted units, refer to the duct
hanger dimensions of the curb for the proper size
3
8
8
of the supply and return air duct connections.
24"
12" (Less Economizer)
36" (With Economizer or
Fixed Air/Motorized
Damper)
24" (Less Economizer)
36" (With Economizer)
24"
20"
72" (For Outdoor Air
Discharge)
AIR FLOW LEGEND
3 4
" CONDENSATE
DRAIN
(must be trapped)
3
19
4
7
44
8
OUTDOOR
COIL
COMPRESSOR
ACCESS
ELECTRIC
HEAT
4 ACCESS
1
2
2
DUCT COVERS - Units are shipped with all air duct
openings covered.
For side duct applications;
1.Remove and discard the supply and return air duct
2.Connect ductwork to duct flanges on the rear of the
For bottom duct applications;
1. Remove the side supply air duct cover to gain
2. Remove and discard the bottom knockout panel.
3. Replace the side duct cover.
4. With filter section access panel removed from the
5. Replace the filter access panel.
1
17
2
1
6
1
17
2
2
REAR VIEW
SIDE SUPPLY AND RETURN
AIR OPENINGS
RETURN AIR
SUPPLY AIR 7
30
8
OUTDOOR AIR
1
19
OUTDOOR AIR
8
(Economizer)
DIMENSION "A"
FIXED
OUTDOOR 12
AIR DAMPER
MOTORIZED
1 2
16
DAMPER
covers.
unit.
access to the bottom supply air knockout panel.
unit, remove and discard the bottom return air
knockout panel.
All dimensions are in inches. They are sub-
ject to change without notice. Certified di-
1
11
2
mensions will be provided upon request.
3
1
11

UTILITIES ENTRY DATA

2
KNOCKOUT
5
4
8
HOLE SIZE
(DIA.)
A 7/8" *
7
7
8
B 2" *
*Knockouts in the bottom of the unit can be located
by the slice in the insulation.
**
Do not remove the 2" knockout ring.
"A" 7
44
8
DETAIL "B"
UNIT WITH FIXED OUTDOOR
AIR/MOTORIZED DAMPER RAIN HOOD
Unitary Products Group
USED FOR
Control Wiring
(Side or Bottom)**
Power Wiring
(Side or Bottom)
1
10
4
B
1
3
2
A
1
8
4
3
4
8