Yamaha MG 6FX Owner's Manual page 22

Front & Rear Panels
8 Level-Meter Signal Switches
These level-meter switches, together with the channel PFL
switches, select the signal that is sent through the
C-R/PHONES control to the C-R OUT jacks, the PHONES
jack, and the level meter.
The following illustration shows how the switch settings corre-
spond to the signal selection.
Switch
PFL
Signal
ON
PFL
2TR - IN
ST
OFF
GROUP 1 - 2
GROUP 3 - 4
1
If the input channel's PFL switch is on (
channel's PFL output it sent to the C-R OUT jacks, PHONES
jacks, and level meter.
2
If the 2TR IN switch is on (
IN jack is sent to the C-R OUT jacks, PHONE jacks, and level
meter. If the 2TR IN switch is off (
Group 1-2, or Group 3-4 signal is sent to the C-R OUT jacks
(as determined by the ST-GROUP and GROUP toggle
switches).
9 C-R/PHONES Control
Controls the level of the signal output to the PHONES jack and
the C-R L and R jacks.
0 Level Meter
This LED display shows the level of the signal selected by the
selection switches described in
OUT and PHONES jacks). The "0" point corresponds to the
standard output level. The indicator lights up red when the out-
put hits the clipping level.
A POWER Indicator
This indicator lights up when the mixer's power is ON.
B ST GRAPHIC EQUALIZER
This 7-band equalizer adjusts the sound of the signal send to
the ST OUT jacks. The equalizer is effective only if the GEQ
switch is set on (
(125, 250, 500, 1k, 2k, 4k, and 8k Hz) over a range of ±12 dB.
MG16/6FX
22
1 2
2TR IN ST-GROUP GROUP
ON
OFF
OFF
OFF
ON
ON
), then only the
), the signal supplied to the 2TR
), then either the Stereo,
8
above (the level to the C-R
). The equalizer cuts or boosts each band
C PHONES Jack
Connector for headphones. This is a balanced stereo phone-type
output jack.
NOTE
D DIGITAL EFFECT
• PROGRAM Dial
Selects the internal digital effect to be applied. You can select
from 16 effects, as shown in the table.
1 HALL 1
2 HALL 2
3 HALL 3
C-R OUT
4 ROOM
&
PHONES
5 PLATE 1
6 PLATE 2
7 PLATE 3
8 GATE REVERB
• PARAMETER Control
Adjusts the parameter (depth, speed, etc.) for the selected
effect.
• AUX1 and AUX2 Controls
Adjust the level of the signal sent from the internal digital
effector to the AUX1 and AUX2 buses.
• ON Switch
Switches use of the internal effect on or off. The internal
effect is applied only if this switch is turned on (
• PFL Switch
Set this switch on (
to the PFL bus.
• GROUP Switches (1-2, 3-4)
Set one or both switches on (
signal to the GROUP 1-2 and/or GROUP 3-4 buses.
• EFFECT RTN Fader
Adjusts the signal level from the internal digital effector to
the STEREO bus.
The signal monitored by these jacks is selected by
the Level-Meter Signal switches and the channel
PFL switches.
9 VOCAL ECHO 1
10 VOCAL ECHO 2
11 VOCAL ECHO 3
12 VOCAL ECHO 4
13 VOCAL REVERB 1
14 VOCAL REVERB 2
15 VOCAL REVERB 3
16 VOCAL REVERB 4
) if you wish to output the effect signal
) to output the internal effect
).