Page 1 Avaya G250 and Avaya G350 CLI Reference 03-300437 Issue 1.1 June 2005...
Page 2 • System administration documents Warranty • Security documents Avaya Inc. provides a limited warranty on this product. Refer to your • Hardware-/software-based security tools sales agreement to establish the terms of the limited warranty. In • Shared information between you and your peers addition, Avaya’s standard warranty language as well as information...
Page 3 A reorder tone is received. operations or procedures that could affect the operation of the Avaya attests that this registered equipment is capable of providing users equipment. If this happens, the telephone company will provide advance access to interstate providers of operator services through the use of notice in order for you to make necessary modifications to maintain access codes.
Page 4 Declarations of Conformity United States FCC Part 68 Supplier’s Declaration of Conformity (SDoC) Avaya Inc. in the United States of America hereby certifies that the equipment described in this document and bearing a TIA TSB-168 label identification number complies with the FCC’s Rules and Regulations 47 CFR Part 68, and the Administrative Council on Terminal Attachments (ACTA) adopted technical criteria.
Page 5: Table Of Contents
Contents About this Book ........Overview .
Page 7 Contents clear radius authentication server ......clear screen ......... . clear snmp trap .
Page 9 Contents disconnect ssh ........distribution-list .
Page 11 Contents ip icmp-errors ......... ip max-arp-entries .
Page 13 Contents nslookup..........nvram initialize .
Page 15 Contents set mediaserver ........set mgc list .
Page 17 Contents show controllers remote ........show copy status .
Page 19 Contents show map-class frame-relay ....... . . show max-ip-registrations ........show mediaserver .
Page 20 (interface) ........20 Avaya G250 and Avaya G350 CLI Reference...
Page 21 Contents start-ip-addr ......... . subnet-mask.
Page 22 Contents 22 Avaya G250 and Avaya G350 CLI Reference...
Page 23: About This Book
The Avaya G250 and Avaya G350 CLI Reference describes the commands used to configure and manage the Avaya G250 and Avaya G350 Media Gateways after they are already installed. For instructions on using these commands to configure and manage the Avaya G250 and Avaya G350 Media Gateways, refer to Administration for the Avaya G250 and Avaya G350 Media Gateways, 03-300436.
Page 24: Conventions
You can download the latest version of the Avaya G250 and Avaya G350 CLI Reference from the Avaya Web site. You must have access to the Internet, and a copy of Acrobat Reader must be installed on your personal computer.
Page 25: Downloading This Book
- PDF Format to download the book in regular PDF format - ZIP Format to download the book as a zipped PDF file Related resources For more information on the Avaya G250 and Avaya G350 Media Gateways and related features, see the following books: Title...
Page 26: Technical Assistance
1-800-242-2121 Toll fraud, call Avaya Toll Fraud Intervention at 1-800-643-2353 International For all international resources, contact your local Avaya authorized dealer for additional help. Trademarks All trademarks identified by the ® or TM are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners.
Page 27: Sending Us Comments
1300 W. 120th Ave. Westminster, CO 80234 USA E-mail, send your comments to: document@avaya.com Fax, send your comments to: 1-303-538-1741 Ensure that you mention the name and number of this book, Avaya G250 and Avaya G350 CLI Reference, 03-300437. Issue 1.1 June 2005...
Page 28 About this Book 28 Avaya G250 and Avaya G350 CLI Reference...
Page 29: Chapter 1: User Levels And Contexts
The contexts you can enter and the commands you can access, depend on the user level from which you log in to the CLI. For example, you can use all show commands in User mode. To configure the Avaya G250/ G350 Media Gateway, you must be in Supervisor or Privileged mode.
Page 30: Contexts
If you are in Supervisor or Privileged mode, you can enter any of the following interface contexts: Interface Console Interface USB Interface Dialer Interface Fast Ethernet Interface VLAN Interface Serial Interface Loopback Interface Tunnel 30 Avaya G250 and Avaya G350 CLI Reference...
Page 31: Entering An Interface
Contexts Entering an Interface You enter an interface context using the interface command, followed by the type of interface, and the interface specification. For the Console and USB interfaces there is no interface specification. Interface types include: FastEthernet Serial VLAN Loopback Console Tunnel...
Page 32: Available Contexts
A GRE tunnel interface. A (if:Tunnel 1)# GRE tunnel is a virtual point-to-point link between two routers at two ends of an Internet cloud. Interface DIaler A Dialer interface (if:Dialer 1)# 1 of 3 32 Avaya G250 and Avaya G350 CLI Reference...
Page 33 Contexts Table 1: List of CLI Contexts (continued) Context Description CLI prompt Banner login For editing a text message (login)# that appears before users login Banner post login For editing a text message (post-login)# that appears after users login Router OSPF OSPF routing protocol (router:ospf)# configuration...
Page 34 Create an ISAKMP peer (peer-grp:vpn.avaya.com)# peer-group group (VPN) crypto map Create a crypto map (VPN) (crypto:1)# survivable-call-engine Configure Standard Local (survivable-call-engine) Survivability (SLS) on the G250 Media Gateway 3 of 3 34 Avaya G250 and Avaya G350 CLI Reference...
Page 35: Chapter 2: Cli Commands
30. This chapter lists all the CLI commands for the Avaya G250/G350 Media Gateway. All commands are supported for both the G250 and the Avaya G250 and Avaya G350 Media Gateways except where otherwise noted. Logging in to the CLI To login to the CLI, you need a username and a password.
Page 36: Using The Cli
For example, typing sh ban login is the same as typing show banner login. However, typing show m matches more than one command and is not executed. Instead the system displays a list such as: Ambiguous Command. Possible commands are: map-class mediaserver mg mgc mm module 36 Avaya G250 and Avaya G350 CLI Reference...
Page 37: Alphabetical Listing Of Cli Commands
Use the add trunk-group command to add a port to a trunk group in the SLS data set on the G250. A trunk port can belong only to a single trunk group. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 38: Area
To configure a stub area for this OSPF interface with IP address 176.1.13.12: G350-001(router:ospf)# area 176.1.13.12 stub To remove the area with IP address 192.168.49.1: G350-001(router:ospf)# no area 192.168.49.1 Related commands default-metric (OSPF), network (OSPF), passive-interface, redistribute (OSPF), timers spf 38 Avaya G250 and Avaya G350 CLI Reference...
Page 39: Arp
Alphabetical listing of CLI commands Use the arp command to add a permanent entry to the Address Resolution Protocol (ARP) cache. Use the no form of this command to remove either a static entry or a dynamically learned entry from the ARP cache. Syntax arp ip_address mac_address no arp ip_address...
Page 40: Arp Timeout
To set the ARP timeout to one hour: G350-001(super)# arp timeout 3600 To restore the default value for ARP timeout: G350-001(super)# no arp timeout Related commands arp, clear arp-cache, max-arp-entries, proxy-arp, show ip arp, show ip reverse-arp 40 Avaya G250 and Avaya G350 CLI Reference...
Page 41: Async Mode Interactive
Alphabetical listing of CLI commands async mode interactive Use the async mode interactive command to enter modem mode every time the proprietary modem cable is plugged into the Console port. Syntax async mode interactive User level read-write Context Interface: Console Related commands async mode terminal,...
Page 42: Async Modem-Init-String
(Console port), async reset-modem (USB port), interface Console, interface usb, ip peer address, authentication, shutdown (interface), shutdown (USB modem), speed (PPP), timeout absolute 42 Avaya G250 and Avaya G350 CLI Reference...
Page 43: Async Modem-Type
Alphabetical listing of CLI commands async modem-type Use the async modem-type command to set the type of modem being used. This command also sets the default modem parameter values such as default initialization string and escape sequence for the specified type of modem. Use the no form of the command to return modem type to its default value of MultiTech-ZBA.
Page 44: Async Reset-Modem (Console Port)
Init string sequence. You can perform this command from within an active PPP session to close the session and allow the USB modem to accept a new call. Note: This command is not supported by the G250. Note: Syntax async reset-modem...
Page 45: Authentication
Alphabetical listing of CLI commands Related commands address, authentication, shutdown (USB modem), speed (PPP), timeout absolute authentication Use the authentication command to set the authentication of ISAKMP policy pre-shared secret. Syntax authentication { pre-share } Parameters Parameter Description Possible Default Values Value The authentication of the ISAKMP policy...
Page 46: Autoneg
Possible Default Values Value The delay before switching to the backup 0-3600 failure_delay interface, in seconds The delay before reverting to the primary 0-3600 secondary_disable_ interface, in seconds delay User level read-write 46 Avaya G250 and Avaya G350 CLI Reference...
Page 47: Backup Interface
Alphabetical listing of CLI commands Context Interface: FastEthernet (L2, L2-L3), Serial (DS1 PPP L2, DS1 PPP L2-L3, DS1 FR L2, DS1 FR-SUB L2, DS1 FR-SUB L2-L3, USP FR L2, USP PPP L2, USP PPP L2-L3), Tunnel (L2, L2-L3) Example To switch over immediately to the backup interface, in case of failure, and pause 60 seconds before reverting to the primary interface: G350-001(if:FastEthernet 10/2)# backup delay 0 60 Related commands...
Page 48: Bandwidth
DS1 FR-SUB L2-L3, USP PPP L2, USP PPP L2-L3, USP FR L2), Fast Ethernet (L2, L2-L3), VLAN (L2, L2-L3), Loopback (L2, L2-L3), Tunnel (L2, L2-L3) Example To manually set the bandwidth for the VLAN interface to 100 KB/s: G350-001(if:Vlan 1)# bandwidth 100 48 Avaya G250 and Avaya G350 CLI Reference...
Page 49: Banner Login
Alphabetical listing of CLI commands Related commands idle-character, ignore dcd, interface serial, invert txclock, nrzi-encoding, transmitter-delay banner login Use the banner login command to enter the login banner configuration mode. Use the no form of this command to set the login banner to its default value. The login banner displays before the user is prompted for the login name.
Page 50: Bc Out
CIR is the committed information rate. The minimum time interval is 10ms, and the device will prevent setting the BC and CIR in a way that violates this minimum. Syntax bc out bits no bc out 50 Avaya G250 and Avaya G350 CLI Reference...
Page 51: Be Out
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The committed burst size in bits 8-39999999 7000 bits User level read-write Context map-class frame-relay Example To configure outbound BC to be 64 Kbit: G350-001(map-class)# bc out 64000 Related commands out, out,...
Page 52: Bootfile
The name of the file to be string, 1-128 bytes null string file-name used as boot file. User level read-write Context dhcp pool Example To set the file “booter” as the bootfile: G350-001(DHCP 5)# bootfile "booter" 52 Avaya G250 and Avaya G350 CLI Reference...
Page 53: Busyout Voip-Dsp
Alphabetical listing of CLI commands To clear the bootfile definition: G350-001(DHCP 5)# no bootfile Related commands client-identifier, default-router, dns-server, domain-name, end-ip-addr, lease, name, next-server, option, server-name, show ip dhcp-pool, start-ip-addr, subnet-mask, value, vendor-specific-option busyout voip-dsp Use the busyout voip-dsp command to put the VoIP engine in busyout (not available) state for a Bit Transfer Rate test.
Page 54: Cablelength Short
Note: The transmit attenuation is configured using the loop length. Note: Syntax cablelength short tx_value Parameters Parameter Description Possible Values Default Value The transmit level 133ft, 266ft, 399ft, 133ft tx_value 533ft, 655ft 54 Avaya G250 and Avaya G350 CLI Reference...
Page 55: Capture Buffer-Mode
Alphabetical listing of CLI commands User level read-write Context Interface: Controller (T1) Example To set the transmit value for the cable to 399ft: G350-001(controller:5/1)# cablelength short 399ft Related commands cablelength long, channel-group, clock source, controller, ds-mode, framing, interface serial, address, linecode (E1), linecode...
Page 56: Capture Buffer-Size
Context general Example G350-001(super)# capture buffer-size 2000 Related commands capture buffer-mode, capture filter-group, capture interface, capture max-frame-size, capture start, capture stop, capture-service, clear capture-buffer, capture-list, name, show capture, show capture-buffer hex 56 Avaya G250 and Avaya G350 CLI Reference...
Page 57: Capture Filter-Group
Alphabetical listing of CLI commands capture filter-group Use the capture filter-group command to apply the specified filter to the packet sniffer. When a capture filter is applied, packets must match the criteria for a rule whose action is ’capture’ in order to be saved to the buffer. Syntax capture filter-group capture_list_id Parameters...
Page 58: Capture Max-Frame-Size
Syntax capture max-frame-size max_frame_size no capture max-frame-size Parameters Parameter Description Possible Default Values Value The maximum number of bytes captured 14-4096 max_frame_size for each packet by the packet sniffer. 58 Avaya G250 and Avaya G350 CLI Reference...
Page 59: Capture Start
Alphabetical listing of CLI commands User level read-write Context general Example G350-001(super)# capture max-frame-size 68 Related commands capture buffer-mode, capture buffer-size, capture filter-group, capture interface, capture start, capture stop, capture-service, clear capture-buffer, capture-list, name, show capture, show capture-buffer hex capture start Use the capture start command to start the packet sniffing service.
Page 60: Capture Stop
In order to upload a capture file, you must first stop the packet sniffing service. Note: Syntax capture stop User level read-write Context general Examples If the packet sniffing service has been enabled by the administrator: G350-001(super)# capture stop 110 packets captured. 60 Avaya G250 and Avaya G350 CLI Reference...
Page 61: Capture-Service
Alphabetical listing of CLI commands If the packet sniffing service has not been enabled by the administrator: G350-001(super)# capture stop The Packet sniffing process is not running. Related commands capture buffer-mode, capture buffer-size, capture filter-group, capture interface, capture max-frame-size, capture start, capture-service, clear capture-buffer,...
Page 62: Channel-Group
If you issue this command with an existing channel number, the timeslots you Note: specify will replace any that already exist. Note: The G250 only supports one channel group per interface. Note: Syntax channel-group channel_number timeslots ts_list speed speed_value no channel-group channel_number...
Page 63: Cir Out
Alphabetical listing of CLI commands Example To create a new channel group number 2, with time slots 5, 6, and 8 and speed of 56: G350-001(controller:5/1)# channel-group 2 timeslots 5-6,8 speed 56 Related commands cablelength long, cablelength short, clock source, controller, ds-mode, framing, interface serial, address,...
Page 64: Class-Identifier
To set an identifier string for vendor-specific option 1: G350-001(DHCP 5/vendor specific 1)# class-identifier "ccp.avaya.com" Related commands value clear arp-cache Use the clear arp-cache command to delete all dynamic entries from the ARP cache. Syntax clear arp-cache [interface|vlan_id|ip_address[mask]] 64 Avaya G250 and Avaya G350 CLI Reference...
Page 65 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The interface name for which to delete interface entries The VLAN ID for which to delete entries 1-3071 vlan_id The host IP address to clear ip_address The IP mask of the subnet to clear mask User level read-write...
Page 66: Clear Ars-Fac
Use the clear ars-fac command to delete an ARS FAC entry in the SLS data set on the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Syntax...
Page 67: Clear Cam
Alphabetical listing of CLI commands clear cam Use the clear cam command to delete all entries from the Contents Address Memory (CAM) table. Syntax clear cam User level read-write Context general Example To clear the CAM table: G350-001(super)# clear cam CAM table cleared.
Page 68: Clear Controller Counters
To clear counters for controller 3, port 1: G350-001(super)# clear controller counters 3/1 clear counters (interface) Use the clear counters command to clear counters for the selected interface or the entire device. Syntax clear counters [interface_type interface_identifier] 68 Avaya G250 and Avaya G350 CLI Reference...
Page 69: Clear Counters (Cna Test Plugs)
Alphabetical listing of CLI commands Parameters Parameter Description Possible Values Default Value The type of interface interface_ type The interface number. The For FastEthernet: 10/2 interface_ format varies depending on identifier For Serial(USP): 2/1 the value of interface_type: For Serial (DS1): For FastEthernet: module/port: 2/1 module/port...
Page 70: Clear Crypto Isakmp
0-32, 766 C-id Note: If you do not enter a connection ID, the entire database is flushed. User level read-write Context general Example To clear C-id 1: G350-001(super)# clear crypto isakmp 1 70 Avaya G250 and Avaya G350 CLI Reference...
Page 71: Clear Crypto Sa
Alphabetical listing of CLI commands To clear the entire database: G350-001(super)# clear crypto isakmp Related commands clear crypto clear crypto sa counters, show crypto ipsec show crypto ipsec transform-set, show crypto isakmp peer, show crypto isakmp peer-group, show crypto isakmp policy, show crypto isakmp...
Page 72: Clear Crypto Sa Counters
Use the clear dial-pattern command to delete a single dialed string pattern entry in the SLS data set on the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 73: Clear Dot1X Config
Specifies the dialed string pattern dialed-string User level read-write Context You must be in the survivable-call-engine context before the clear dial-pattern command will work. Example G250-001(super-survivable-call-engine)# clear dial-pattern 49139 Dial Pattern 49139 was removed. Related commands trunk-group, clear ars-fac, clear survivable-config,...
Page 74: Clear Extension
Use the clear extension command to delete a particular extension number in the SLS data set. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Syntax clear extension extnum...
Page 75: Clear Fragment
Alphabetical listing of CLI commands Related commands trunk-group, clear ars-fac, clear survivable-config, clear dial-pattern, clear trunk-group, remove trunk-group, save config, ars-fac, date-format, dial-pattern, extension, extension-password, ip-codec-set, max-ip-registrations, survivable-call-engine, trunk-group, show ars-fac, show date-format, show dial-pattern, show extension, show ip-codec-set, show last-pim-update, show max-ip-registrations,...
Page 76: Clear Ip Dhcp-Client Statistics
Use the clear ip dhcp-client statistics command to clear the DHCP client statistics counters. Syntax clear ip dhcp-client statistics User level read-only Context general, Interface: Fast Ethernet 76 Avaya G250 and Avaya G350 CLI Reference...
Page 77: Clear Ip Dhcp-Server Binding
Alphabetical listing of CLI commands Note: When you use this command in the interface context, the counters of the Note: specified interface are cleared. When you use this command in the general context, all DHCP client counters are cleared. Example G350-001(config-if:FastEthernet 10/2)# clear ip dhcp-client statistics Related commands ip address...
Page 78: Clear Ip Dhcp Server Statistics
Related commands clear ip dhcp-server binding, ip dhcp activate pool, ip dhcp ping packets, ip dhcp ping timeout, dhcp pool, dhcp-server, show ip dhcp-pool, show ip dhcp-server bindings, show ip dhcp-server statistics 78 Avaya G250 and Avaya G350 CLI Reference...
Page 79: Clear Ip Domain Statistics
Alphabetical listing of CLI commands clear ip domain statistics Use the clear ip domain statistics command to clear the DNS Resolver’s statistics counters. Syntax clear ip domain statistics User level read-write Context general Example G350-001(super)# clear ip domain statistics Related commands ip domain list, ip domain...
Page 80: Clear Ip Rtp Header-Compression
There is no renegotiation of parameters. Note: Syntax clear ip rtp header-compression [interface_type interface_number] Parameters Parameter Description Possible Default Values Value The type of interface interface_type The interface number interface_number User level read-only 80 Avaya G250 and Avaya G350 CLI Reference...
Page 81: Clear Ip Tcp Header-Compression
Alphabetical listing of CLI commands Context general Example To clear header compression statistics for all interfaces: G350-001(super)# clear ip rtp header-compression Related commands clear ip tcp header-compression, ip rtp compression-connections, ip rtp header-compression, max-period, ip rtp max-time, ip rtp non-tcp-mode, ip rtp port-range, ip tcp...
Page 82: Clear Ip Tftp-Server Statistics
82 Avaya G250 and Avaya G350 CLI Reference...
Page 83: Clear Ip Traffic
Alphabetical listing of CLI commands clear ip traffic Use the clear ip traffic command to clear the IP counters. Syntax clear ip traffic User level read-only Context general clear logging file Use the clear logging file command to delete the message log file being stored in non-volatile memory (NVRAM), including the history log, and open a new, empty log file.
Page 84: Clear Logging Server
84 Avaya G250 and Avaya G350 CLI Reference...
Page 85: Clear Mgc List
Alphabetical listing of CLI commands clear mgc list Use the clear mgc list command to remove entries from the Media Gateway Controller list. Multiple entries can be removed together, by specifying a list of IP addresses separated by commas. If no arguments are provided, all entries are removed. Syntax clear mgc list [ipaddress1,…] Parameters...
Page 86: Clear Port Mirror
The port number of the destination port dest_port User level read-write Context general Example To disable the mirroring of port 5/1 by port 5/3: G350-001(super)# clear port mirror 5/1 5/3 Related commands set port mirror, show port mirror 86 Avaya G250 and Avaya G350 CLI Reference...
Page 87: Clear Port Static-Vlan
Alphabetical listing of CLI commands clear port static-vlan Use the clear port static-vlan command to delete statically configured VLANs from the port. Syntax clear port static-vlan module/port_range vlan_id Parameters Parameter Description Possible Default Values Value The module number module The port number or range of port numbers port_range The VLAN ID to remove vlan_id...
Page 88: Clear Radius Authentication Server
G350-001(super)# clear radius authentication server secondary Related commands set radius authentication, set radius authentication retry-number, set radius authentication retry-time, set radius authentication secret, set radius authentication server, set radius authentication udp-port, show radius authentication 88 Avaya G250 and Avaya G350 CLI Reference...
Page 89: Clear Screen
Alphabetical listing of CLI commands clear screen Use the clear screen command to clear the current terminal display. Syntax clear screen User level read-only Context general Related commands banner login, banner post-login, hostname, line, show banner login, show banner post-login, terminal length, terminal width...
Page 90: Clear Ssh-Client Known-Hosts
SCP server authentication after an SCP server public key change. Syntax clear ssh-client known-hosts User level admin Context general Example G350-001(super)# clear ssh-client known-hosts Related commands crypto key generate, disconnect ssh, ssh, show ip ssh 90 Avaya G250 and Avaya G350 CLI Reference...
Page 91: Clear Survivable-Config
Alphabetical listing of CLI commands clear survivable-config Use the clear survivable-config command to set the SLS parameters in the G250 to their default values. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 92: Clear Tcp Syn-Cookies Counters
Use the clear tcp syn-cookies counters command to clear the SYN cookies counters. Syntax clear tcp syn-cookies counters User level read-only Context general 92 Avaya G250 and Avaya G350 CLI Reference...
Page 93: Clear Trunk-Group
Use the clear trunk-group command to delete a trunk group entry from the SLS data set in the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Syntax...
Page 94: Clear Utilization Cpu
Use the clear vlan command to delete an existing VLAN and its interface. When you clear a VLAN, all ports assigned to that VLAN are returned to the default VLAN. Syntax clear vlan vlan_id | {name vlan_name} 94 Avaya G250 and Avaya G350 CLI Reference...
Page 95: Client-Identifier
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The VLAN number vlan_id Keyword specifying to identify the VLAN by name the VLAN name. The VLAN name. vlan_name If you wish to enter a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 96: Clock Source
Use the clock source command to configure the clock source for an E1/T1 controller. Use the no form of the command to return the clock source to the default value of line. Syntax clock source {line | internal} no clock source 96 Avaya G250 and Avaya G350 CLI Reference...
Page 97: Cna-Testplug
(E1), linecode (T1), remote, show controllers cna-testplug The G250/G350 features one CNA test plug, which has its own CNA configuration context. Use the cna-testplug command to enter the CNA test plug configuration context. Syntax cna-testplug 1 User level read-write...
Page 98: Cna-Testplug-Service
To enable the CNA test plug service: G350-003# cna-testplug-service The Converged Network Analyzer test plug is enabled. Related commands clear counters (CNA test plugs), cna-testplug, control-port, rtp-echo-port, rtp-test-port, scheduler, show cna testplug, shutdown (CNA test plugs), test-rate-limit 98 Avaya G250 and Avaya G350 CLI Reference...
Page 99: Composite-Operation
Alphabetical listing of CLI commands composite-operation Use the composite-operation command to edit the specified composite operation. If the composite operation does not exist, it is created. Syntax composite-operation index Parameters Parameter Description Possible Default Values Value The composite operation number 12-19 index User level...
Page 100: Continuous-Channel
(VPN), keepalive-track, pre-shared-key, self-identity, show crypto isakmp peer, suggest-key Related commands - VPN - crypto map crypto map, description (crypto map), transform-set, dscp, set peer (crypto map), peer-group, show crypto map 100 Avaya G250 and Avaya G350 CLI Reference...
Page 101: Control-Port
Alphabetical listing of CLI commands control-port Use the control-port command to set the UDP port on which the CNA test plug listens for test requests from schedulers. Use the no form of the command to return to default control port. Syntax control-port port no control port...
Page 102: Cookie
Use the cookie command to set the cookie for the current list. Syntax cookie cookie_number Parameters Parameter Description Possible Values Default Value The ID number of the cookie 0-268435455 cookie_number User level read-write 102 Avaya G250 and Avaya G350 CLI Reference...
Page 103: Copy Capture-File Ftp
Alphabetical listing of CLI commands Context ip access-control-list, ip qos-list, ip capture-list, ip pbr-list, ip crypto-list Example To specify the cookie for QoS list 440 as 257: G350-001(QoS 440)# cookie 257 Related commands - Packet sniffing composite-operation, copy capture-file ftp, copy capture-file scp, copy capture-file...
Page 104: Copy Capture-File Scp
Parameters Parameter Description Possible Default Values Value The file name on the FTP server filename The IP address of the FTP server User level read-write Context general 104 Avaya G250 and Avaya G350 CLI Reference...
Page 105: Copy Capture-File Tftp
Alphabetical listing of CLI commands Example To upload the packet sniffing buffer to the g350.cap file on the FTP server at IP address 135.64.10.33: G350-001(super)# copy capture-file scp g350.cap 135.64.10.33 Related commands composite-operation, cookie, copy capture-file ftp, copy capture-file tftp, ip-rule (policy, policy-based routing, packet sniffing), owner,...
Page 106: Copy Dhcp-Binding Ftp
Example To copy the binding file with file name dhcp_binding.txt to the host with IP address 192.168.49.10: G350-001(super)# copy dhcp-binding ftp dhcp_binding.txt 192.168.49.10 Related commands copy dhcp-binding scp, copy dhcp-binding tftp 106 Avaya G250 and Avaya G350 CLI Reference...
Page 107: Copy Dhcp-Binding Scp
Alphabetical listing of CLI commands copy dhcp-binding scp Use the copy dhcp-binding scp command to copy the dhcp bindings file to a remote server using FTP. Syntax copy dhcp-binding scp filename ip Parameters Parameter Description Possible Values Default Value File name with full path string filename IP address of the host...
Page 108: Copy Ftp Ew_Archive
EW_archive Use the copy ftp EW_archive command to download Avaya G350 Manager software from an FTP server. The FTP command prompts for the username and password after the command is entered. Note: This command is not supported by the G250.
Page 109: Copy Ftp License-File
Alphabetical listing of CLI commands User level read-write Context general Example To download the g350.img file from the FTP server at IP address 135.64.10.33, using login dan: G350-001(super)# copy ftp EW_archive g350.img 135.64.10.33 Username: dan Password: Related commands copy ftp module, copy ftp SW_imageA,...
Page 110: Copy Ftp Module
Use the copy ftp module command to download firmware from an FTP server into a media module. The FTP command prompts for the username and password after the command is entered. Note: This command is not supported by the G250. Note: Syntax copy ftp module module_number filename ip...
Page 111: Copy Ftp Phone-Image
Use the copy ftp phone-image command to download a file from a remote FTP server to phone image bank A, B, C, or D in the local gateway TFTP directory. Note: The G250/G350 prompts you for a username and password when you enter a Note: command to transfer a file using FTP.
Page 112: Copy Ftp Phone-Script
Use the copy ftp phone-script command to download a file from a remote FTP server to phone script bank A or B on the local G250/G350 TFTP directory. Note: The G250/G350 prompts you for a username and password when you enter a Note: command to transfer a file using FTP.
Page 113: Copy Ftp Startup-Config
Alphabetical listing of CLI commands Example G350-001# copy ftp phone-scriptA 46xxupgrade.txt 192.168.49.10 Confirmation - do you want to continue (Y/N)? y Username: anonymous Password: Beginning download operation ... This operation may take up to 20 seconds. Please refrain from any other operation during this time. Related commands copy ftp phone-image,...
Page 114: Copy Ftp Sw_Imagea
Bank A. The command prompts for the username and password. Syntax copy ftp SW_imageA filename ip Parameters Parameter Description Possible Default Values Value File name on the FTP server filename IP address of the FTP server User level read-write Context general 114 Avaya G250 and Avaya G350 CLI Reference...
Page 115: Copy Ftp Sw_Imageb
Alphabetical listing of CLI commands Example To download the software image file, g350.img, from the FTP site at IP address 135.64.10.33 using login dan: G350-001(super)# copy ftp SW_imageA g350.img 135.64.10.33 Username: dan Password: Related commands copy ftp EW_archive, copy ftp module, copy ftp SW_imageB,...
Page 116: Copy Phone-Script Ftp
Use the copy phone-script ftp command to upload a phone script file from the local G250/G350 TFTP directory to a remote server, using FTP. Syntax copy phone-scriptA|phone-scriptB|phone-scriptC|phone-scriptD ftp filename ip Parameters...
Page 117: Copy Phone-Script Scp
Use the copy phone-script scp command to upload a phone script file from the local G250/G350 TFTP directory to a remote server, using SCP. Syntax copy phone-scriptA|phone-scriptB|phone-scriptC|phone-scriptD scp filename ip Parameters...
Page 118: Copy Phone-Script Tftp
Use the copy phone-script tftp command to upload a phone script file from the local G250/G350 TFTP directory to a remote server, using TFTP. Syntax copy phone-scriptA|phone-scriptB|phone-scriptC|phone-scriptD tftp filename ip Parameters...
Page 119: Copy Running-Config Ftp
Alphabetical listing of CLI commands copy running-config ftp Use the copy running-config ftp command to upload the current configuration to a file on an FTP server. The command prompts for the username and password. Uncommitted changes to the configuration are included. Note: After you change the configuration, run the copy running-config Note:...
Page 120: Copy Running-Config Scp
120 Avaya G250 and Avaya G350 CLI Reference...
Page 121: Copy Running-Config Startup-Config
Use the copy running-config tftp command to upload the current configuration to a file on a TFTP server. Uncommitted changes to the configuration are included. To use this command, you need to have an active TFTP server. If Avaya Network Manager is running, you do not require an additional TFTP server.
Page 122: Copy Scp License-File
Use the copy scp license-file command to download a VPN license from an SCP server. Syntax copy scp license-file filename ip 122 Avaya G250 and Avaya G350 CLI Reference...
Page 123: Copy Scp Phone-Script
Use the copy scp phone-script command to download a file from a remote SCP server to phone script bank A or B in the local G250/G350 TFTP directory. Syntax copy scp phone-scriptA|phone-scriptB filename ip Parameters...
Page 124: Copy Scp Startup-Config
Syntax copy scp startup-config filename ip Parameters Parameter Description Possible Default Values Value Name of file to create on SCP server filename IP address of SCP server 124 Avaya G250 and Avaya G350 CLI Reference...
Page 125: Copy Startup-Config Ftp
Alphabetical listing of CLI commands User level read-write Context general Example G350-001(super)# copy scp startup-config c:\config_files\router1.cfg 192.168.49.10 copy startup-config ftp Use the copy startup-config ftp command to upload the current configuration to a file on an FTP server. The command prompts for the username and password. Uncommitted changes to the configuration are not included.
Page 126: Copy Startup-Config Scp
IP address of the SCP server User level read-write Context general Example To upload the current configuration to the router1.cfg file on the SCP server at IP address 192.168.49.10: G350-001(super)# copy startup-config scp c:\config_files\router1.cfg 192.168.49.10 126 Avaya G250 and Avaya G350 CLI Reference...
Page 127: Copy Startup-Config Tftp
Use the copy startup-config tftp command to upload the current configuration to a file on a TFTP server. Uncommitted changes to the configuration are not included. To use this command, you need to have an active TFTP server. If Avaya Network Manager is running, you do not require an additional TFTP server.
Page 128: Copy Tftp Ew_Archive
TFTP. To use this command, you need to have an active TFTP server, and to create a file into which to download the data. If Avaya Network Manager is running, you do not require an additional TFTP server.
Page 129: Copy Tftp License-File
Alphabetical listing of CLI commands Related commands copy ftp EW_archive, copy ftp module, copy ftp SW_imageA, copy ftp SW_imageB, copy tftp module, copy tftp SW_imageA, copy tftp SW_imageB, dir, set boot bank, show boot bank, show download software status, show image version copy tftp license-file Use the copy tftp license-file command to download a VPN license from a TFTP server.
Page 130: Copy Tftp Module
TFTP. To use this command, you need to have an active TFTP server, and to create a file into which to download the software. If Avaya Network Manager is running, an additional TFTP server is not required.
Page 131: Copy Tftp Phone-Image
Use the copy tftp phone-image command to download a file from a remote TFTP server to phone image bank A, B, C, or D in the local G250/G350 TFTP directory. Syntax copy tftp phone-imageA|phone-imageB|phone-imageC|phone-imageD filename...
Page 132: Copy Tftp Phone-Script
CLI Commands copy tftp phone-script Use the copy tftp phone-script command to download a file from a remote TFTP server to phone script bank A or B in the local G250/G350 TFTP directory. Syntax copy tftp phone-scriptA|phone-scriptB filename ip Parameters...
Page 133: Copy Tftp Startup-Config
TFTP file to the Startup Configuration NVRAM. To use this command, you need to have an active TFTP server, and to create a file into which to download the data. If Avaya Network Manager is running, an additional TFTP server is not required.
Page 134: Copy Tftp Sw_Imagea
Use the copy tftp SW_imageA command to update the software image in Bank A of the media gateway. To use this command, you need to have an active TFTP server, and to create a file into which to download the data. If Avaya Network Manager is running, an additional TFTP server is not required. Syntax...
Page 135: Copy Tftp Sw_Imageb
Use the copy tftp SW_imageB command to update the software image in Bank B of the media gateway. To use this command, you need to have an active TFTP server, and to create a file into which to download the data. If Avaya Network Manager is running, an additional TFTP server is not required. Syntax...
Page 136: Cos
Context ip qos-list composite-operation Example To set the priority for composite operation 12 to 3: G350-001(QoS 440/CompOp 12)# cos 3 Related commands dscp (policy, policy-based routing, packet sniffing), name, show composite-operation 136 Avaya G250 and Avaya G350 CLI Reference...
Page 137: Crypto Ipsec Df-Bit
Alphabetical listing of CLI commands crypto ipsec df-bit Use the crypto ipsec df-bit command to set the Don’t-Fragment bit to one of the following modes: clear — the DF bit of the encapsulated packet is never set, and PMTUD is not maintained for the IPSec tunnel.
Page 138: Crypto Ipsec Minimal-Pmtu
Use the crypto ipsec minimal-pmtu command to set the minimal PMTU value which can be applied to an SA when the G250/G350 participates in Path MTU Discovery (PMTUD) for the tunnel pertaining to that SA. Use the no form of the command to restore the minimal PMTU to the default value: 300.
Page 139: Crypto Ipsec Transform-Set
Alphabetical listing of CLI commands Context general Example G350-001(super)# no crypto ipsec nat-transparency udp-encapsulation Related commands crypto isakmp nat keepalive, ip crypto-group crypto ipsec transform-set Use the crypto ipsec transform-set command to enter the IKE phase 2 (IPSec) transform-set context and create or edit IPSec parameters for the VPN tunnel. Use the no form of the command to delete IKE phase 2 (IPSec) parameters for the VPN tunnel.
Page 140 Example 3: To configure an IPSec transform set with authentication only: G350-001(super)# crypto ipsec transform-set ts3 esp-null esp-md5-hmac G350-001(config-transform:ts3)# Example 4: To enter the crypto IPSec transform-set context: G350-001(super)# crypto ipsec transform-set ts1 G350-001(config-transform:ts1)# 140 Avaya G250 and Avaya G350 CLI Reference...
Page 141: Crypto Isakmp Invalid-Spi-Recovery
Alphabetical listing of CLI commands Related commands crypto map, crypto isakmp peer, crypto isakmp peer-group, crypto isakmp policy, crypto-group, crypto-list, mode, pfs, set security-association lifetime, show crypto ipsec transform-set crypto isakmp invalid-spi-recovery Use the crypto isakmp invalid-spi-recovery command to enable invalid SPI recovery (default setting).
Page 142: Crypto Isakmp Peer
Syntax [no] crypto isakmp peer {address peer-address | fqdn fqdn-str} 142 Avaya G250 and Avaya G350 CLI Reference...
Page 143: Crypto Isakmp Peer-Group
A string of up to fqdn ISAKMP peer. 110 characters. User level read-write Context general Examples G350-001(super)# crypto isakmp peer address 149.49.70.1 G350-001(config-peer:149.49.70.1)# G350-001(super)# crypto isakmp peer fqdn vpn.lnd.ny.avaya.com G350-001(config-peer:vpn.lnd.ny.avaya.com)# Related commands continuous-channel, crypto ipsec transform-set, crypto map, crypto isakmp peer-group, crypto...
Page 144: Crypto Isakmp Policy
Use the crypto isakmp policy command to enter the crypto ISAKMP policy context and create or edit IKE Phase 1 parameters. Syntax crypto isakmp policy id 144 Avaya G250 and Avaya G350 CLI Reference...
Page 145: Crypto Isakmp Suggest-Key
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The identity of the ISAKMP policy 1-20 User level read-write Context general Example G350-001(super)# crypto isakmp policy 1 G350-001(config-isakmp:1)# Related commands authentication, crypto ipsec transform-set, crypto map, crypto isakmp peer, crypto isakmp peer-group,...
Page 146: Crypto Key Generate
Note: This command does not close active sessions. Note: Note: This command can take several minutes to run (depending on CPU speed). Note: 146 Avaya G250 and Avaya G350 CLI Reference...
Page 147: Crypto Map
Example G350-001(super)# crypto key generate Generating DSA key, This command may take a few minutes ..Key was created. Key version: SSH2, DSA Key Fingerprint: dd:60:59:fa:e0:47:b8:db:e3:1c:17:8d:4c:14:9a:0f root@avaya Related commands clear ssh-client known-hosts, disconnect ssh, ssh, show ip ssh crypto map Use the crypto map command to enter crypto map context and create or edit a crypto map.
Page 148: De Pre-Mark
(0-5) over the BC (committed burst) level and under the BE (excess burst) level as Delete Eligible (DE) packets. Use the no form of the command to return the threshold to its default value. Syntax de pre-mark threshold_percent no de pre-mark 148 Avaya G250 and Avaya G350 CLI Reference...
Page 149: De-Buffer-Size
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Value Values The threshold percent 1-100 100 (no pre-mark) threshold_percent User level read-write Context map-class frame-relay Related commands out, out, out, de-buffer-size de-buffer-size Use the de-buffer-size command to set the buffer size for frames marked as drop-eligible. Use the no form of the command to return the drop-eligible buffer to its default size.
Page 150: Default-Metric (Ospf)
1-65535 default_ metric User level read-write Context Router-OSPF Example To set the default metric for redistributed routes to 50: G350-001(router:ospf)# default-metric 50 Related commands area, network (OSPF), passive-interface, redistribute (OSPF), timers spf 150 Avaya G250 and Avaya G350 CLI Reference...
Page 151: Default-Metric (Rip)
Alphabetical listing of CLI commands default-metric (RIP) Use the default-metric command to set the default metric of redistributed routes for the RIP protocol. Use the no form of this command to restore the default value. Syntax default-metric default_metric no default-metric Parameters Parameter Description...
Page 152: Default-Router
Possible Values Default Value A list of up to eight IP A list of IP addresses 0.0.0.0 ip-addr-list addresses for the default router. separated by spaces User level read-write Context dhcp pool 152 Avaya G250 and Avaya G350 CLI Reference...
Page 153: Description (Interface)
Alphabetical listing of CLI commands Example To set 164.35.2.4 and 135.64.102.3 as default router IP addresses: G350-001(DHCP 5)# default-router 164.35.2.4 135.64.102.3 Related commands bootfile, client-identifier, dns-server, domain-name, end-ip-addr, lease, name, next-server, option, server-name, show ip dhcp-pool, start-ip-addr, subnet-mask, value, vendor-specific-option description (interface) Use the description command to configure a description for the current interface.
Page 154: Description (Dns Resolver)
G350-001(name-server-list:1)# description "All DNS servers" Related commands clear ip domain statistics, ip domain list, ip domain lookup, ip domain name-server-list, domain retry, ip domain timeout, name-server, nslookup, show ip domain, show ip domain statistics, 154 Avaya G250 and Avaya G350 CLI Reference...
Page 155: Description (Crypto Map)
Alphabetical listing of CLI commands description (crypto map) Use the description command to enter a description for the crypto map. Use the no form of the command to clear a description for the crypto map. Syntax [no] description desc Parameters Parameter Description Possible...
Page 156: Description (Isakmp Peer)
Values Value The description of the ISAKMP peer. string of desc 1-80 Note: If you wish to include spaces in the characters description, you must enclose the string in quotation marks (“”) 156 Avaya G250 and Avaya G350 CLI Reference...
Page 157: Description (Isakmp Peer Group)
1-80 Note: If you wish to include spaces in the characters description, you must enclose the string in quotation marks (“”) User level read-write Context crypto isakmp peer-group Example G350-001(config-peer-grp:vpn.avaya.com)# description "Avaya peer group" Issue 1.1 June 2005...
Page 158: Description (Ip Rule)
(“”) User level read-write Context ip crypto-list/ip-rule Example G350-001(Crypto 901/ip rule 20)# description "vpn tunnel to uk headquarters" Related commands destination-ip, crypto-list, ip-rule (VPN), local-address, protect crypto map, source-ip, show ip crypto-list 158 Avaya G250 and Avaya G350 CLI Reference...
Page 159: Description (Object Tracking)
Alphabetical listing of CLI commands description (object tracking) Use the description command to enter a description of an object tracker. Use the no form of this command to use the default description, which is the object tracker’s ID. Syntax [no] description text Parameters Parameter Description...
Page 160: Destination-Ip
G350-001(QoS 460/rule 22)# destination-ip host 135.64.104.102 To specify that rule 17 applies to packets whose destination IP address is in the range of 176.13.0.0 through 176.13.255.255: G350-001(QoS 460/rule 17)# destination-ip 176.13.0.0 0.0.255.255 160 Avaya G250 and Avaya G350 CLI Reference...
Page 161: Dialer Modem-Interface
Alphabetical listing of CLI commands Related commands - Packet sniffing dscp (policy, policy-based routing, packet sniffing), icmp, ip-protocol, show ip capture-list, source-ip, destination-port, source-port, destination-port, udp source-port Related commands - Policy-based routing dscp (policy, policy-based routing, packet sniffing), next-hop (policy-based routing), show ip next-hop-list,...
Page 162: Dialer Order
Restarts dialing using the most recently last- successful string and continues to the next dial successful string in a list if a call fails. User level read-write Context interface dialer Example G350-001(if:Dialer 1)# dialer order last-successful 162 Avaya G250 and Avaya G350 CLI Reference...
Page 163: Dialer Persistent
Alphabetical listing of CLI commands Related commands interface dialer, dialer modem-interface, dialer persistent, dialer persistent delay, dialer persistent initial delay, dialer persistent max-attempts, dialer persistent re-enable, dialer string, dialer wait-for-ipcp dialer persistent Use the dialer persistent command to force the dialer to attempt to reconnect every second.
Page 164: Dialer Persistent Initial Delay
Use the no form of the command to return the delay to the default value. Note: Use this command to prevent the Dialer interface from dialing out after the G250/ Note: G350 is reset because the primary interface does not become active immediately after the reset.
Page 165: Dialer Persistent Max-Attempts
Alphabetical listing of CLI commands User level read-write Context interface dialer Example G350-001(if:Dialer 1)# dialer persistent initial delay 20 Related commands interface dialer, dialer modem-interface, dialer order, dialer persistent, dialer persistent delay, dialer persistent max-attempts, dialer persistent re-enable, dialer string, dialer wait-for-ipcp dialer persistent max-attempts Use the dialer persistent max-attempts command to set the number of consecutive...
Page 166: Dialer Persistent Re-Enable
Example G350-001(if:Dialer 1)# dialer persistent re-enable Related commands interface dialer, dialer modem-interface, dialer order, dialer persistent, dialer persistent delay, dialer persistent initial delay, dialer persistent max-attempts, dialer string, dialer wait-for-ipcp 166 Avaya G250 and Avaya G350 CLI Reference...
Page 167: Dialer String
Alphabetical listing of CLI commands dialer string Use the dialer string command to add a phone number to the dial list. Use the no form of the command to delete a number from the dial list. Syntax dialer string id dial-string Parameters Parameter Description...
Page 168: Dialer Wait-For-Ipcp
Use the dir command to show the files that have been downloaded to the media gateway using the Avaya G250 and Avaya G350 CLI Reference Download interface and the SNMP MIB. Syntax 168 Avaya G250 and Avaya G350 CLI Reference...
Page 169: Disable Link Encryption
Alphabetical listing of CLI commands User level read-only Context general Example To display a list of downloaded files: G350-001(super)# dir M# file ver num file type file location file description -- ---- -------- ---------- ------------- ---------------- MM712 SW RT Image Nv-Ram MM712 - image MM711...
Page 170: Disable Media Encryption
User level admin Context general Example To disable H.248 signalling encryption: G350-001(super)# disable link encryption disable media encryption Use the disable media encryption command to disable Avaya media encryption (SRTP, AEA, RTP/AES). Syntax disable media encryption User level admin Context general...
Page 171: Distribution-List
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The number of the SSH session to disconnect session_id User level admin Context general Related commands clear ssh-client known-hosts, crypto key generate, ssh, show ip ssh distribution-list Use the distribution-list command to apply a distribution policy rule for incoming or outgoing routing information in route updates.
Page 172: Dns-Server
Possible Values Default Value A list of up to eight IP A list of IP addresses 0.0.0.0 ip-addr-list addresses for the separated by spaces Domain Name Server User level read-write Context dhcp pool 172 Avaya G250 and Avaya G350 CLI Reference...
Page 173: Domain-Name
User level read-write Context dhcp pool Example To set the domain name to “avaya.com”: G350-001(DHCP 5)# domain-name avaya.com Related commands bootfile, client-identifier, default-router, dns-server, end-ip-addr, lease, name, next-server, option, server-name, show ip dhcp-pool, start-ip-addr, subnet-mask, value, vendor-specific-option Issue 1.1 June 2005...
Page 174: Dscp (Policy, Policy-Based Routing, Packet Sniffing)
G350-001(QoS 440/CompOp 17)# dscp 55 Related commands - Packet sniffing destination-ip, icmp, ip-protocol, show ip capture-list, source-ip, destination-port, source-port, destination-port, udp source-port Related commands - Policy-based routing destination-ip, next-hop (policy-based routing), show ip next-hop-list, show ip-rule 174 Avaya G250 and Avaya G350 CLI Reference...
Page 175: Dscp (Object Tracking)
Alphabetical listing of CLI commands Related commands - Policy composite-operation, destination-ip, icmp, show composite-operation, show ip-rule, source-ip, destination-port, established, source-port, destination-port, source-port, cos, name dscp (object tracking) Use the dscp command to set the DSCP value for the packets of the RTR probes. Use the no form of this command to restore the value to the default value of 48.
Page 176: Dscp-Table
To enter configuration mode for DSCP table entry 21: G350-001(QoS 440)# dscp-table 21 Related commands composite-operation, cookie, ip-rule (policy, policy-based routing, packet sniffing), owner, show composite-operation, show dscp-table, show ip-rule, show list 176 Avaya G250 and Avaya G350 CLI Reference...
Page 177: Ds-Mode
Alphabetical listing of CLI commands ds-mode Use the ds-mode command to specify the mode of the controller. Note: When you change the ds-mode, you must copy the running configuration to the Note: startup configuration and reset the device. Syntax ds-mode {e1|t1} Parameters Parameter Description...
Page 178: Duplex
User level read-only Context Interface: FastEthernet (L2, L2-L3) Example To specify full duplex for the FastEthernet interface: G350-001(super-if:FastEthernet 1.1)# duplex full Related commands autoneg, shutdown (interface), speed (interface), traffic-shape rate 178 Avaya G250 and Avaya G350 CLI Reference...
Page 179: Dynamic-Cac
Use the dynamic-cac command to set the dynamic CAC bearer bandwidth limit for the current interface. You can also specify an activation priority for the interface. In case more than one interface with a BBL value is up, the G250/G350 reports the BBL of the interface with the highest activation priority.
Page 180: Encapsulation
Context Interface: Serial (DS1 PPP L2, DS1 PPP L2-L3, DS1 FR L2, USP PPP L2, USP PPP L2-L3, USP FR L2) Example To create a Frame-Relay interface: G350-001(if:Serial 2/1:1)# encapsulation frame-relay ietf 180 Avaya G250 and Avaya G350 CLI Reference...
Page 181: Encapsulation Pppoe
Alphabetical listing of CLI commands Related commands - Frame relay encapsulation frame-relay interface-dlci, frame-relay lmi-n391dte, frame-relay lmi-n392dte, frame-relay lmi-n393dte, frame-relay lmi-type, frame-relay priority-dlci-group, frame-relay traffic-shaping, address Related commands - PPP encapsulation address, keepalive (PPP), ppp timeout ncp, ppp timeout retry, show interfaces encapsulation pppoe Use the pppoe command to enable the PPPoE client.
Page 182: Encryption
3des — Triple DES - 168 bits. aes — Advanced Encryption Standard - 128 bits. aes-192 — Advanced Encryption Standard - 192 bits. aes-256 — Advanced Encryption Standard - 256 bits. User level read-write Context crypto isakmp policy 182 Avaya G250 and Avaya G350 CLI Reference...
Page 183: End-Ip-Addr
Alphabetical listing of CLI commands Example G350-001(config-isakmp:1)# encryption 3des Related commands authentication, crypto isakmp policy, description (ISAKMP policy), group, hash, lifetime, show crypto isakmp policy end-ip-addr Use the end-ip-addr command to set the end IP address of a DHCP pool IP address range. For manual/reservation leasing, set the end IP address to be identical to the start IP address.
Page 184: Enhanced Security
TELNET, FTP, TFTP, SNMP Inhibits output data traffic during powerup/error states Inhibits modification of the active IPSEC transform-set parameters In the G250 only: the G250 switches from performing symmetric encryption with a hardware accelerator, to software-based encryption Note: This command can only be executed on FIPS-ready hardware.
Page 185: Erase Phone-Script
Alphabetical listing of CLI commands Context general Example G350-001# erase phone-imageA Beginning erase operation ..Done! Related commands copy ftp phone-script, copy scp phone-script, copy ftp phone-image, copy tftp phone-image, copy tftp phone-script, ip tftp-server file-system size, show application-memory, show ip tftp-server files, show download phone-script-file...
Page 186: Exit
User level read-only Context Example To exit the rule 22 configuration context, and then the access-control-list 330 context: G350-001(ACL 330/ip rule 22)# exit G350-001(ACL 330)# exit G350-001(super)# Related commands reset, logout, show logout 186 Avaya G250 and Avaya G350 CLI Reference...
Page 187: Fail-Retries
Alphabetical listing of CLI commands fail-retries Use the fail-retries command to specify how many consecutive unanswered probes change the status of an RTR operation device from up to down. Use the no form of this command to restore the value to the default. Syntax [no] fail-retries retries Parameters...
Page 188: Fair-Voip-Queue
WFVQ, you must enable another queuing mode, using either the voip-queue or the priority-queue command in interface context. Note: The commands fair-voip-queue and voip-queue are mutually exclusive, Note: and cannot both appear in a configuration script. Syntax fair-voip-queue User level admin 188 Avaya G250 and Avaya G350 CLI Reference...
Page 189: Fdl
Alphabetical listing of CLI commands Context Interface: Serial (DS1 PPP L2-L3, DS1 PPP L2, DS1 FR L2, USP FR L2, USP PPP L2, USP PPP L2-L3), FastEthernet (L2, L2-L3) - when traffic shaping is configured Example G350-001(super-if:FastEthernet 10/2)# fair-voip-queue Related commands - WFVQ fair-queue-limit, voip-queue, voip-queue-delay Use the fdl command to define the type of Facility Data Link loopback that the remote line is...
Page 190: Fragment
(policy-based routing), show ip next-hop-list, show ip-rule Related commands - Policy composite-operation, dscp (policy, policy-based routing, packet sniffing), destination-ip, icmp, show composite-operation, show ip-rule, source-ip, destination-port, established, source-port, destination-port, source-port, cos, name 190 Avaya G250 and Avaya G350 CLI Reference...
Page 191: Fragment Chain
Alphabetical listing of CLI commands fragment chain Use the fragment chain command to set the maximum number of fragments that can comprise a single IP packet destined to the router. Use the no form of this command to set the fragment chain to its default value.
Page 192: Fragment Size
User level read-write Context general Example To set the maximum number of packets to reassemble to 150: G350-001(super)# fragment size 150 Related commands clear fragment, fragment chain, fragment timeout, show fragment 192 Avaya G250 and Avaya G350 CLI Reference...
Page 193: Fragment Timeout
Alphabetical listing of CLI commands fragment timeout Use the fragment timeout command to set the maximum number of seconds to reassemble a fragmented IP packet destined to the router. Use the no form of this command to set the fragment timeout to its default value. Note: No IP reassembly of packets in transit through the router is performed.
Page 194: Frame-Relay Class-Dlci
To associate Virtual Channel number 17 with the map-class frame-relay named “myVoIpClass”: G350-001(super-if:Serial 2/1:1)#frame-relay class-dlci 17 myVoIpClass Related commands clear frame-relay counters, interface serial, map-class frame-relay, show frame-relay map, show frame-relay pvc brief, show interfaces 194 Avaya G250 and Avaya G350 CLI Reference...
Page 195: Frame-Relay Interface-Dlci
Alphabetical listing of CLI commands frame-relay interface-dlci Use the frame-relay interface-dlci command to associate a frame relay Virtual Channel with this interface. This VC will be in the primary role (that is, will determine the operational status of the interface). Use the no form of this command to delete the association of the VC and the sub-interface.
Page 196: Frame-Relay Lmi-N391Dte
To set the number of seconds between status enquiry messages to 17 seconds: G350-001(if:Serial 2/1:1)# frame-relay lmi-n391dte 17 Related commands encapsulation, frame-relay interface-dlci, frame-relay lmi-n392dte, frame-relay lmi-n393dte, frame-relay lmi-type, frame-relay priority-dlci-group, frame-relay traffic-shaping, ip address 196 Avaya G250 and Avaya G350 CLI Reference...
Page 197: Frame-Relay Lmi-N392Dte
Alphabetical listing of CLI commands frame-relay lmi-n392dte Use the frame-relay lmi-n392dte command to set the maximum number of unanswered status enquiries the equipment accepts before declaring the interface down. Use the no form of this command to revert to the default value. Syntax [no] frame-relay lmi-n392dte threshold Parameters...
Page 198: Frame-Relay Lmi-N393Dte
To set the number of events over which the error threshold is calculated to 5: G350-001(if:Serial 2/1:1)# frame-relay lmi-n393dte 5 Related commands encapsulation, frame-relay interface-dlci, frame-relay lmi-n391dte, frame-relay lmi-n392dte, frame-relay lmi-type, frame-relay priority-dlci-group, frame-relay traffic-shaping, ip address 198 Avaya G250 and Avaya G350 CLI Reference...
Page 199: Frame-Relay Lmi-Type
Alphabetical listing of CLI commands frame-relay lmi-type Use the frame-relay lmi-type command to manually define the type of the Local Management Interface (LMI) to use. Use the no form of this command to specify automatic detection of the LMI type (auto-sensing). If auto-sense fails, ANSI is used as the default.
Page 200: Frame-Relay Priority-Dlci-Group
VC number 19 to the Normal to Low priority traffic: G350-001(if:Serial 2/1:1.1)# frame-relay priority-dlci-group 17 18 19 Related commands encapsulation, frame-relay interface-dlci, frame-relay lmi-n391dte, frame-relay lmi-n392dte, frame-relay lmi-n393dte, frame-relay lmi-type, frame-relay traffic-shaping, ip address 200 Avaya G250 and Avaya G350 CLI Reference...
Page 201: Frame-Relay Traffic-Shaping
Alphabetical listing of CLI commands frame-relay traffic-shaping Use the frame-relay traffic-shaping command to turn on/off traffic shaping and Frame-Relay fragmentation. Virtual Channels that are not explicitly assigned to a map-class frame-relay, are assigned to the default map-class frame-relay. Use the no form of this command to turn off traffic shaping. Syntax [no] frame-relay traffic-shaping User level...
Page 202: Frequency
Use the frequency command to specify how often to send RTR probes. Use the no form of this command to restore the frequency value to the default. Syntax [no] frequency frequency-value [seconds | milliseconds] 202 Avaya G250 and Avaya G350 CLI Reference...
Page 203: Group
Alphabetical listing of CLI commands Parameters Parameter Description Possible Values Default Value A number indicating the 1-60 seconds 5 seconds frequency-value frequency of RTR probes 1000-60,000 5000 milliseconds milliseconds Keyword indicating to set seconds the frequency of RTR probes in units of seconds Keyword indicating to set milliseconds the frequency of RTR...
Page 204: Hash
[no] hash hash-method Parameters Parameter Description Possible Default Values Value The hash method for the ISAKMP policy: hash-method sha — Secure Hash Algorithm md5 — Message Digest algorithm 5 User level read-write 204 Avaya G250 and Avaya G350 CLI Reference...
Page 205: Hostname
CLI prompt to the default. Syntax hostname [hostname_string] no hostname Parameters Parameter Description Possible Default Values Value The hostname a string of up to G250 or hostname_ 20 characters G350 string User level read-write Context general Issue 1.1 June 2005...
Page 206: Icc-Vlan
Related commands - VLAN configuration clear port static-vlan, clear vlan, interface vlan, set port static-vlan, set port vlan, set port vlan-binding-mode, trunk, vlan, show cam vlan, show port vlan-binding-mode, show trunk, show vlan 206 Avaya G250 and Avaya G350 CLI Reference...
Page 207: Icmp
Alphabetical listing of CLI commands icmp Use the icmp command to specify that the current rule applies to a specific type of ICMP packet. Use the no form of this command to specify that the rule applies to all packets except those of the specified ICMP type.
Page 208: Icmp In-Echo-Limit
Possible Default Values Value The number of echo requests 1-10000 size User level read-write Context general Example To set the echo request limit at 500 packets per second: G350-001(super)# icmp in-echo-limit 500 208 Avaya G250 and Avaya G350 CLI Reference...
Page 209: Idle-Character
Alphabetical listing of CLI commands idle-character Use the idle-character command to set the bit pattern used to indicate an idle line. Use the no form of this command to restore the default value. For E1 and USP interfaces, the default value is flags.
Page 210: Ignore Dcd
Use the no form of this command to restore the default setting, which is IKE main mode. Note: Aggressive mode is one of the prerequisites for working with dynamic IP Note: addresses. Syntax [no] initiate mode aggressive User level read-write 210 Avaya G250 and Avaya G350 CLI Reference...
Page 211: Interface Console
Alphabetical listing of CLI commands Context crypto isakmp peer Example G350-001(config-peer:149.49.70.1)# initiate mode aggressive Related commands continuous-channel, description (ISAKMP peer), crypto isakmp peer, isakmp-policy, keepalive (VPN), keepalive-track, pre-shared-key, self-identity, show crypto isakmp peer, suggest-key interface Console Use the interface Console command to enter the console interface configuration mode. The interface is created if it does not exist.
Page 212: Interface Dialer
Example G350-001(super)# interface dialer 1 G350-001(if:dialer 1)# Related commands dialer modem-interface, dialer order, dialer persistent, dialer persistent delay, dialer persistent initial delay, dialer persistent max-attempts, dialer persistent re-enable, dialer string, dialer wait-for-ipcp 212 Avaya G250 and Avaya G350 CLI Reference...
Page 213: Interface Fastethernet
Alphabetical listing of CLI commands interface FastEthernet Use the interface FastEthernet command to enter Interface FastEthernet configuration mode. Use the no form of this command to delete an IP interface. If the specified interface does not exist, the system creates it and enters its configuration mode. Syntax [no] interface FastEthernet [module/port[.ip_interface]] Parameters...
Page 214: Interface Loopback
To delete the Layer 3 sub-interface: G350-001(super)# no interface Loopback 1.0 Related commands description (interface), interface Console, interface FastEthernet, interface serial, interface tunnel, interface usb, interface vlan, address, admin-state, broadcast-address, load-interval, show ip interface brief 214 Avaya G250 and Avaya G350 CLI Reference...
Page 215: Interface Serial
Alphabetical listing of CLI commands interface serial Use the interface serial command to enter serial interface or sub interface configuration mode. If the specified interface or sub interface does not exist, the system creates it and enters its configuration mode. Use the no form of the command to delete the interface.
Page 216: Interface Tunnel
(interface), interface Console, interface FastEthernet, interface Loopback, interface serial, interface usb, interface vlan, address, admin-state, broadcast-address, load-interval, show ip interface brief Related commands - GRE tunneling interface FastEthernet, tunnel dscp, tunnel mode 216 Avaya G250 and Avaya G350 CLI Reference...
Page 217: Interface Usb
Note: This command is not supported by the G250. Note: The usb interface always exists, but is disabled by default. Use the no shutdown command to enable the interface.
Page 218: Interface Vlan
G350-001(super)# no interface Vlan 2.1 Related commands - IP interface configuration description (interface), interface Console, interface FastEthernet, interface Loopback, interface serial, interface tunnel, interface usb, address, admin-state, broadcast-address, load-interval, show ip interface brief 218 Avaya G250 and Avaya G350 CLI Reference...
Page 219: Interface-Keepalive Bypass-Logic
Alphabetical listing of CLI commands Related commands - VLAN configuration clear port static-vlan, clear vlan, icc-vlan, set port static-vlan, set port vlan, set port vlan-binding-mode, trunk, vlan, show cam vlan, show port vlan-binding-mode, show trunk, show vlan interface-keepalive bypass-logic The interface-keepalive bypass-logic command provides future support of an alternative internal path for RTR probes, in cases where next-hop is configured for the RTR probes.
Page 220: Ip Access-Control-List
Values Value The Access Control list number 300-399 list_number User level read-write Context general Example To create access control list 320 and enter its configuration mode: G350-001(super)# ip access-control-list 320 G350-001(ACL 320)# 220 Avaya G250 and Avaya G350 CLI Reference...
Page 221: Ip Access-Group
Alphabetical listing of CLI commands Related commands access-group, policy-list-copy, qos-group, qos-list, simulate, pre-classification, show access-control-list, show ip qos-list ip access-group Use the ip access-group command to activate a specific Access Control list for a specific direction, on the current interface. Use the no form of this command to suspend the Access Control list for a specific direction.
Page 222: Ip Address
G350-001(if:FastEthernet 10/2)# ip address 192.168.22.33 255.255.255.0 Related commands description (interface), interface Console, interface FastEthernet, interface Loopback, interface serial, interface tunnel, interface usb, interface vlan, admin-state, broadcast-address, load-interval, show ip interface brief 222 Avaya G250 and Avaya G350 CLI Reference...
Page 223: Ip Address Dhcp
Alphabetical listing of CLI commands ip address dhcp Use the ip address dhcp command to enable IP address negotiation via DHCP. Use the no form of this command to disable IP address negotiation via DHCP. Note: The ip address dhcp command can only be used on FastEthernet 10/2. Note: Note: You cannot configure both ip address dhcp and keepalive-track (object...
Page 224: Ip Address Negotiated
G350-001(config-if:FastEthernet 10/2)# ip address negotiated Related commands ppp ipcp dns request ip admin-state Use the ip admin-state command to set the administrative state of an IP interface. The default state is up. Syntax ip admin-state up|down 224 Avaya G250 and Avaya G350 CLI Reference...
Page 225: Ip Bootp-Dhcp Network
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value Keyword specifying the administrative state of the IP interface is set to up (active) Keyword specifying the administrative state down of the IP interface is set to down (inactive) User level read-write Context...
Page 226: Ip Bootp-Dhcp Relay
Use the ip bootp-dhcp relay command to enable relaying of BOOTP and DHCP requests to the BOOTP/DHCP server. Use the no form of this command to disable relaying of BOOTP and DHCP requests. Syntax [no] ip bootp-dhcp relay User level read-write Context general 226 Avaya G250 and Avaya G350 CLI Reference...
Page 227: Ip Bootp-Dhcp Server
Alphabetical listing of CLI commands Example To enable relaying of BOOTP and DHCP requests: G350-001(super)# ip bootp-dhcp relay To disable relaying of BOOTP and DHCP requests: G350-001(super)# no ip bootp-dhcp relay Related commands ip bootp-dhcp network, ip bootp-dhcp server ip bootp-dhcp server Use the ip bootp-dhcp server command to add a BOOTP/DHCP server to handle BOOTP/DHCP requests received by this interface.
Page 228: Ip Broadcast-Address
Use the ip capture-list command to enter the specified capture-list context. If the specified capture-list does not exist, it is created. Syntax ip capture-list capture_list_id no ip capture-list capture_list_id 228 Avaya G250 and Avaya G350 CLI Reference...
Page 229: Ip Crypto-Group
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The capture list number 500-599 capture_list_id User level read-write Context general Example G350-001(super)# ip capture-list 501 G350-001(super-Cap 501)# Related commands capture buffer-mode, capture buffer-size, capture filter-group, capture interface, capture max-frame-size, capture...
Page 230: Ip Crypto-List
You cannot delete an active crypto-list. You must first deactivate the list, using the Note: no form of the ip crypto-group command. Syntax [no] ip crypto-list index Parameters Parameter Description Possible Default Values Value The crypto-list number 901-999 index 230 Avaya G250 and Avaya G350 CLI Reference...
Page 231: Ip Default-Gateway
Alphabetical listing of CLI commands User level read-write Context general Example G350-001(super)# ip crypto-list 901 G350-001(Crypto 901)# Related commands crypto ipsec transform-set, crypto map, crypto isakmp peer, crypto isakmp peer-group, crypto isakmp policy, description (ip rule), destination-ip, ip-rule (VPN), crypto-group, local-address, protect crypto map, source-ip, show ip...
Page 232: Ip Dhcp Activate Pool
When you deactivate a pool, the binding information of all IP addresses from the pool that were allocated is erased. Syntax [no] ip dhcp activate pool pool_id Parameters Parameter Description Possible Default Values Value The pool index 1-32 pool_id User level read-write 232 Avaya G250 and Avaya G350 CLI Reference...
Page 233: Ip Dhcp Client Client-Id
Alphabetical listing of CLI commands Context general Example To activate DHCP pool 5: G350-001(super)# ip dhcp activate pool 5 To deactivate DHCP pool 5: G350-001(super)# no dhcp activate pool 5 Related commands clear ip dhcp-server binding, clear ip dhcp server statistics, ip dhcp ping packets,...
Page 234: Ip Dhcp Client Hostname
Use the ip dhcp client hostname command to specify the client host name for the DHCP client. Use the no form of this command to restore the default value, which is the G250 or G350’s hostname.
Page 235: Ip Dhcp Client Lease
Alphabetical listing of CLI commands ip dhcp client lease Use the ip dhcp client lease command to set the lease requested by the DHCP client. Use the no form of this command to specify the default behavior, which is that the client does not request a lease from the DHCP server.
Page 236: Ip Dhcp Client Request
A keyword indicating the Option router DHCP client is requesting requested the list of default routers from the DHCP server. User level read-write Context Interface: Fast Ethernet Example G350-001(config-if:FastEthernet 10/2)#ip dhcp client request router 236 Avaya G250 and Avaya G350 CLI Reference...
Page 237: Ip Dhcp Pool
Alphabetical listing of CLI commands Related commands clear ip dhcp-client statistics, ip address dhcp, ip dhcp client client-id, ip dhcp client hostname, ip dhcp client lease, release dhcp, renew dhcp, show ip dhcp-client, show ip dhcp-client statistics ip dhcp pool Use the ip dhcp pool to create a DHCP pool or to enter the context of a DHCP pool.
Page 238: Ip Dhcp Ping Packets
238 Avaya G250 and Avaya G350 CLI Reference...
Page 239: Ip Dhcp Ping Timeout
Alphabetical listing of CLI commands ip dhcp ping timeout Use the ip dhcp ping timeout command to set the ping timeout. This is the time the DHCP server waits for a reply to a sent ping packet before allocating an IP address to a DHCP client. A lack of reply after the configured timeout indicates that the IP address is not in use and therefore can be allocated.
Page 240: Ip Dhcp-Server
Use the ip directed-broadcast command to enable net-directed broadcast forwarding. Use the no form of this command to disable net-directed broadcasts on an interface. Syntax [no] ip directed-broadcast User level read-write 240 Avaya G250 and Avaya G350 CLI Reference...
Page 241: Ip Distribution Access-Default-Action
Alphabetical listing of CLI commands Context Interface: Serial (DS1 PPP L2-L3, DS1 PPP L3, DS1 FR-SUB L2-L3, DS1 FR-SUB L3, USP PPP L2-L3, USP PPP L3), FastEthernet (L2-L3, L3), VLAN (L2-L3, L3) Related commands interface FastEthernet, interface serial, interface vlan, ip netbios-rebroadcast ip distribution access-default-action Use the ip distribution access-default-action command to set the default action...
Page 242: Ip Distribution Access-List
The IP router address of the network router_ip The IP network wildcard address router_wildcard Keyword that specifies the value can be any IP address User level read-write Context general 242 Avaya G250 and Avaya G350 CLI Reference...
Page 243: Ip Distribution Access-List-Cookie
Alphabetical listing of CLI commands Example To create distribution list 1, whose default action is to discard information from the network 10.10.0.0: G350-001(super)# ip distribution access-list 1 23 deny 10.10.0.0 0.0.255.255 To configure RIP distribution access list number 2 permitting distribution and learning of router 10.1.1.1: G350-001(super)# ip distribution access-list 2 24 permit 10.1.1.1 To configure RIP distribution access list number 20 permitting distribution and learning of all...
Page 244: Ip Distribution Access-List-Copy
The source distribution access list 1-99 source_list The destination distribution access list 1-99 destination_list User level read-write Context general Example To copy distribution list 1 to list 3: G350-001(super)# ip distribution access-list-copy 1 3 244 Avaya G250 and Avaya G350 CLI Reference...
Page 245: Ip Distribution Access-List-Name
Alphabetical listing of CLI commands ip distribution access-list-name Use the ip distribution access-list-name command to set the distribution list name. Syntax ip distribution access-list-name distribution_list_number name Parameters Parameter Description Possible Default Values Value The number of the distribution list 1-99 distribution_ list_number The distribution list name...
Page 246: Ip Distribution Access-List-Owner
To define a name that includes spaces, enclose the entire name in quotation Note: marks (for example, “New York”). User level read-write Context general Example To specify Jane Wiley as the owner of distribution list 78: G350-001(super)# ip distribution access-list-owner 78 “Jane Wiley” 246 Avaya G250 and Avaya G350 CLI Reference...
Page 247: Ip Domain List
The domain-name domain-name User level read-write Context general Examples G350-001(super)# ip domain list 2 support.avaya.com G350-001(super)# no ip domain list support.avaya.com Related commands clear ip domain statistics, ip domain lookup, ip domain name-server-list,...
Page 248: Ip Domain Lookup
Once you are in the context of the list, use the command to name-server add or delete DNS servers in the list. Syntax ip domain name-server-list index Parameters Parameter Description Possible Values Default Value The index number of the list index 248 Avaya G250 and Avaya G350 CLI Reference...
Page 249: Ip Domain Retry
Alphabetical listing of CLI commands User level read-write Context general Example G350-001(super)# ip domain name-server-list 1 G350-001(name-server-list:1)# Related commands clear ip domain statistics, description (DNS resolver), ip domain list, ip domain lookup, domain retry, ip domain timeout, name-server, nslookup, show ip domain, show ip domain statistics...
Page 250: Ip Domain Timeout
Example G350-001(super)# ip domain timeout 4 Related commands clear ip domain statistics, ip domain list, ip domain lookup, ip domain name-server-list, domain retry, nslookup, show ip domain, show ip domain statistics 250 Avaya G250 and Avaya G350 CLI Reference...
Page 251: Ip Http
Use the ip http command to enable the HTTP server. Use the no form of the command to disable the HTTP server. Note: This command is not supported by the G250. Note: Syntax ip http [port port_number] [no] ip http...
Page 252: Ip Icmp Redirect
Use the ip icmp-errors command to set ICMP error messages to ON. Use the no form of this command to set ICMP error messages to OFF. Syntax [no] ip icmp-errors User level read-write Context general Related commands show ip icmp 252 Avaya G250 and Avaya G350 CLI Reference...
Page 253: Ip Max-Arp-Entries
Alphabetical listing of CLI commands ip max-arp-entries Use the ip max-arp-entries command to specify the maximum number of ARP cache entries allowed in the ARP cache. Use the no form of this command to restore the default value. In order for this command to take effect, you must copy the running configuration to the startup configuration and reset the device.
Page 254: Ip Netbios-Rebroadcast
PPP L3, USP PPP L2-L3), FastEthernet (L2-L3, L3), VLAN (L2-L3, L3) Example To enable rebroadcasting of NETBIOS packets received by and sent from the FastEthernet interface: G350-001(if:FastEthernet 10/2)# ip netbios-rebroadcast both Related commands interface FastEthernet, interface serial, interface vlan, ip directed-broadcast 254 Avaya G250 and Avaya G350 CLI Reference...
Page 255: Ip Netmask-Format
Alphabetical listing of CLI commands ip netmask-format Use the ip netmask-format command to specify the format of netmasks in the show command output. Use the no form of this command to restore the format to the default format. Syntax ip netmask-format mask_format no ip netmask-format Parameters Parameter...
Page 256: Ip Next-Hop-List
The number of the next hop list 1-20 next_hop_number User level read-write Context general Example G350-001(super)# ip next-hop-list 2 G350-001(super-next hop list 2)# Related commands pbr-group, pbr-list, show ip active-lists, show ip active-pbr-lists, show ip pbr-list 256 Avaya G250 and Avaya G350 CLI Reference...
Page 257: Ip Ospf Authentication
Alphabetical listing of CLI commands ip ospf authentication Use the ip ospf authentication command to specify the authentication type for an interface. Use the no form of the command to remove the authentication type for an interface. Syntax ip ospf authentication auth_type no ip ospf authentication Parameters Parameter...
Page 258: Ip Ospf Authentication-Key
258 Avaya G250 and Avaya G350 CLI Reference...
Page 259: Ip Ospf Cost
Alphabetical listing of CLI commands ip ospf cost Use the ip ospf cost command to statically configure the interface cost metric. Use the no form of this command to return to dynamic calculation of the cost. Syntax ip ospf cost cost no ip ospf cost Parameters Parameter...
Page 260: Ip Ospf Dead-Interval
260 Avaya G250 and Avaya G350 CLI Reference...
Page 261: Ip Ospf Hello-Interval
Alphabetical listing of CLI commands ip ospf hello-interval Use the ip ospf hello-interval command to specify the time interval between hello packets the router sends. Use the no form of this command to set the hello-interval to its default value. Syntax ip ospf hello-interval seconds no ip ospf hello-interval...
Page 262: Ip Ospf Message-Digest-Key
262 Avaya G250 and Avaya G350 CLI Reference...
Page 263: Ip Ospf Network Point-To-Multipoint
Alphabetical listing of CLI commands ip ospf network point-to-multipoint Use the ip ospf network point-to-multipoint command to specify the network type as point-to-multipoint for the interface, and to increase the OSPF timers appropriately. Use the no form of the command to return the interface to point-to-point topology. Syntax [no] ip ospf network point-to-multipoint User level...
Page 264: Ip Ospf Router-Id
Use the ip ospf router-id command to configure the IP address of the router interface. Syntax ip ospf router-id router_id Parameters Parameter Description Possible Default Value Values The IP address of the router lowest existing router_id IP interface 264 Avaya G250 and Avaya G350 CLI Reference...
Page 265: Ip Pbr-Group
Alphabetical listing of CLI commands User level read-write Context general Example To set the IP address of the router interface to 192.168.49.1: G350-001(super)# ip ospf router-id 192.168.49.1 Related commands ip ospf authentication, ip ospf authentication-key, ip ospf cost, ip ospf dead-interval, ip ospf hello-interval,...
Page 266: Ip Pbr-List
The list number of the policy list 801-899 list_number being entered User level read-write Context general Example G350-001(super)# ip pbr-list 802 G350-001(super-PBR 802)# Related commands next-hop-list, pbr-group, show ip active-lists, show ip active-pbr-lists, show ip pbr-list 266 Avaya G250 and Avaya G350 CLI Reference...
Page 267: Ip Peer Address
Alphabetical listing of CLI commands ip peer address Use the ip peer address command to change the IP address offered by the Console or USB interface to a requesting calling host during PPP/IPCP connection establishment. By default, the interface offers its own IP address plus one. Syntax ip peer address ip-address Parameters...
Page 268: Ip Policy-List-Copy
Example To copy the settings of access control list 330 to list 340: G350-001(super)# ip policy-list-copy 330 340 Related commands access-control-list, access-group, qos-group, qos-list, simulate, pre-classification, show ip access-control-list, show ip qos-list 268 Avaya G250 and Avaya G350 CLI Reference...
Page 269: Ip Proxy-Arp
Alphabetical listing of CLI commands ip proxy-arp Use the ip proxy-arp command to enable proxy ARP on an interface. Use the no form of this command to disable proxy ARP on an interface. Syntax [no] ip proxy-arp User level read-write Context Interface: FastEthernet (L2-L3, L3), VLAN (L2-L3, L3) Example...
Page 270: Ip Qos-List
QoS list does not exist, the system creates it and enters its configuration mode. Syntax ip qos-list list_number Parameters Parameter Description Possible Default Values Value The policy list number 400-499 list_number User level read-write Context general 270 Avaya G250 and Avaya G350 CLI Reference...
Page 271: Ip Redirects
Alphabetical listing of CLI commands Example To create QoS list 440 and enter its configuration context: G350-012# ip qos-list 440 G350-012(QoS 440)# Related commands access-control-list, access-group, policy-list-copy, qos-group, simulate, pre-classification, show ip access-control-list, show ip qos-list ip redirects Use the ip redirects command to enable the sending of redirect messages on the current interface.
Page 272: Ip Rip Authentication Mode
Use the ip rip authentication mode command to specify the type of authentication used in RIP Version 2 packets. Use the no form of this command to restore the default value, none. Syntax ip rip authentication mode [simple|none] no ip rip authentication mode 272 Avaya G250 and Avaya G350 CLI Reference...
Page 273: Ip Rip Default-Route-Mode
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value Keyword indicating that the clear text simple authentication should be used Keyword indicating that no authentication none should be used User level read-write Context Interface: Serial (DS1 PPP L2-L3, DS1 PPP L3, DS1 FR-SUB L2-L3, DS1 FR-SUB L3, USP PPP L2-L3, USP PPP L3), FastEthernet (L2-L3, L3), VLAN (L2-L3, L3), Loopback (L2-L3, L3), Tunnel (L2-L3, L3) Example...
Page 274: Ip Rip Poison-Reverse
The split-horizon technique prevents information about routes from exiting the router interface through which the information was received. This prevents routing loops. Poison-reverse updates explicitly indicate that a network or subnet is unreachable. Poison-reverse updates are sent to defeat large routing loops. 274 Avaya G250 and Avaya G350 CLI Reference...
Page 275: Ip Rip Rip-Version
Alphabetical listing of CLI commands Syntax [no] ip rip poison-reverse User level read-write Context Interface: Serial (DS1 PPP L2-L3, DS1 PPP L3, DS1 FR-SUB L2-L3, DS1 FR-SUB L3, USP PPP L2-L3, USP PPP L3), FastEthernet (L2-L3, L3), VLAN (L2-L3, L3), Loopback (L2-L3, L3), Tunnel (L2-L3, L3) Related commands ip distribution...
Page 276: Ip Rip Send-Receive-Mode
— RIP receives updates on the interface and sends only a default route. listen-only — RIP receives updates on the interface and does not transmit them. The route metric 1-15 default_ index route_metric 276 Avaya G250 and Avaya G350 CLI Reference...
Page 277: Ip Rip Split-Horizon
Alphabetical listing of CLI commands User level read-write Context Interface: Serial (DS1 PPP L2-L3, DS1 PPP L3, DS1 FR-SUB L2-L3, DS1 FR-SUB L3, USP PPP L2-L3, USP PPP L3), FastEthernet (L2-L3, L3), VLAN (L2-L3, L3), Loopback (L2-L3, L3), Tunnel (L2-L3, L3) Example To set the RIP protocol to receive and transmit update on the Serial interface: G350-001(if:Serial 2/1:1)# ip rip send-receive-mode talk-listen...
Page 278: Ip Route
The preference of the route High, preference Keyword that specifies that the route is not permanent disabled if the interface is down Keyword that creates a static discard route Null0 User level read-write Context general 278 Avaya G250 and Avaya G350 CLI Reference...
Page 279: Ip Routing
Alphabetical listing of CLI commands Example To create a static route on IP address 132.55.0.0 with subnet mask 255.255.0.0 following the path 132.55.4.45, with cost of 3 and priority of high: G350-001(super)# ip route 132.55.0.0 255.255.0.0 132.55.4.45 3 high To remove the static route defined for IP address 134.66.0.0: G350-001(super)# no ip route 134.66.0.0 255.255.0.0 To create a static discard route on IP address 134.66.0.0: G350-001(super)# ip route 134.66.0.0 255.255.0.0 Null0...
Page 280: Ip Rtp Compression-Connections
280 Avaya G250 and Avaya G350 CLI Reference...
Page 281: Ip Rtp Header-Compression
Alphabetical listing of CLI commands ip rtp header-compression Use the ip rtp header-compression command to enable both RTP and TCP header compression on the current interface. Use the no form of this command to disable both RTP and TCP compression on the current interface. Note: The ip rtp header-compression command always overrides the ip tcp Note:...
Page 282: Ip Rtp Max-Period
282 Avaya G250 and Avaya G350 CLI Reference...
Page 283: Ip Rtp Max-Time
Alphabetical listing of CLI commands ip rtp max-time Use the ip rtp max-time command to set the maximum number of seconds between full headers. Syntax ip rtp max-time number Parameters Parameter Description Possible Default Values Value The maximum number of seconds between 1-255 number full headers...
Page 284: Ip Rtp Non-Tcp-Mode
284 Avaya G250 and Avaya G350 CLI Reference...
Page 285: Ip Rtp Port-Range
Alphabetical listing of CLI commands ip rtp port-range Use the ip rtp port-range command to set the range of UDP ports considered as RTP on the current interface. Set the range to be identical to the peer’s configuration. Some vendors use port range 49,152 through 65,535. For interoperability, the same port range should be used.
Page 286: Ip Simulate
Interface: Serial (DS1 PPP L2, DS1 PPP L2-L3, DS1 FR-SUB L2, DS1 FR-SUB L2-L3, USP PPP L2, USP PPP L2-L3), Loopback (L2, L2-L3), FastEthernet (L2-L3, L3), Tunnel (L2, L2-L3), VLAN (L2, L2-L3) 286 Avaya G250 and Avaya G350 CLI Reference...
Page 287: Ip Snmp-Server
Alphabetical listing of CLI commands Example To simulate the effects of applying access control list 330 to a packet entering the media gateway through the Fast Ethernet interface, from IP address 192.67.85.12 to IP address 192.67.54.25: G350-001(if:FastEthernet 10/2)# ip simulate 330 in 192.67.85.12 192.67.54.25 ip Related commands access-control-list,...
Page 288: Ip Ssh
Use the no form of the command to disable the SSH service, and close any open connections currently using SSH. When disabling the service, the G250/G350 issues a message listing all current management interfaces. If SSH is currently the only enabled management interface, the user is warned that the remote connection will be lost.
Page 289: Ip Tcp Compression-Connections
Alphabetical listing of CLI commands ip tcp compression-connections Use the ip tcp compression-connections command to specify the total number of TCP header compression connections supported on the current interface. Use the no form of this command to restore the default value of 16 connections. Syntax [no] ip tcp compression-connections number Parameters...
Page 290: Ip Telnet
(using the show running-config command). To see the status of this command, use the show protocol command (refer to show protocol on page 676). Syntax ip telnet [port port_number] no ip telnet 290 Avaya G250 and Avaya G350 CLI Reference...
Page 291: Ip Telnet-Client
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value Keyword that changes the default port of the port Telnet server The number of the new port for the Telnet 1-65535 port_number server User level admin Context genera Related commands telnet-client, telnet...
Page 292: Ip Tftp-Server
TFTP file system size. The Sniffer cache application may have been configured to use up to 1000 Kb of the default TFTP allocation of 18560 Kb, which would cause a conflict when setting the TFTP allocation to a high value. 292 Avaya G250 and Avaya G350 CLI Reference...
Page 293: Ip Unnumbered
Alphabetical listing of CLI commands Syntax [no] ip tftp-server file-system-size size Parameters Parameter Description Possible Default Values Value The TFTP server total fie size in Kb 256-19456 18560 size User level Read-write Context general Example G350-001# ip tftp-server file-system-size 18128 To change ip tftp-server file system size, copy the running configuration to the start-up configuration file, and reset the device Related commands...
Page 294 1 Context Interface: Dialer, Serial (DS1 PPP L2, DS1 PPP L2-L3, DS1 FR-SUB L2, DS1 FR-SUB L2-L3, USP PPP L2, USP PPP L2-L3) Tunnel (L2, L2-L3) User level read-write 294 Avaya G250 and Avaya G350 CLI Reference...
Page 295: Ip Vrrp
Alphabetical listing of CLI commands Example G250-001(super-if:Dialer 1)# ip unnumbered 1 loopback 1 G250-001(super-if:Dialer 1)# ip unnumbered 2 vlan 1 G250-001(super-if:Dialer 1)# ip unnumbered 3 serial 2/1:1 G250-001(super-if:Dialer 1)# ip unnumbered 4 serial 2/1:1 ip vrrp Use the ip vrrp command to create a virtual router on the current interface. Use the no form of this command to delete a virtual router.
Page 296: Ip Vrrp Address
Use the ip vrrp auth-key command to set the virtual router simple password authentication for the virtual router ID. Use the no form of this command to disable simple password authentication for the virtual router instance. Syntax [no] ip vrrp vr_id auth-key key_string 296 Avaya G250 and Avaya G350 CLI Reference...
Page 297: Ip Vrrp Override Addr Owner
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The virtual router ID 1-255 vr_id The password string key_string User level read-write Context Interface: FastEthernet (L2-L3, L2), VLAN (L2-L3, L2) Example To specify the password authentication for virtual router 1 as “sec01”: G350-001(if:Vlan 2)# ip vrrp 1 auth-key sec01 Related commands vrrp,...
Page 298: Ip Vrrp Preempt
By default, preemption is enabled. Syntax [no] ip vrrp vr_id preempt Parameters Parameter Description Possible Default Values Value The virtual router ID 1-255 vr_id User level read-write Context Interface: FastEthernet (L2-L3, L2), VLAN (L2-L3, L2) 298 Avaya G250 and Avaya G350 CLI Reference...
Page 299: Ip Vrrp Primary
Alphabetical listing of CLI commands Example To specify that virtual router 1 preempts a lower priority master: G350-001(if:Vlan 2)# ip vrrp 1 preempt Related commands vrrp, ip vrrp address, ip vrrp auth-key, ip vrrp override addr owner, ip vrrp primary, ip vrrp priority, ip vrrp...
Page 300: Ip Vrrp Priority
G350-001(if:Vlan 2)# ip vrrp 1 priority 10 Related commands vrrp, ip vrrp address, ip vrrp auth-key, ip vrrp override addr owner, ip vrrp preempt, ip vrrp primary, ip vrrp timer, router vrrp, show ip vrrp 300 Avaya G250 and Avaya G350 CLI Reference...
Page 301: Ip Vrrp Timer
Alphabetical listing of CLI commands ip vrrp timer Use the ip vrrp timer command to set the virtual router advertisement timer value for the virtual router ID. Use the no form of this command to restore the default value. Syntax [no] ip vrrp vr_id timer value Parameters Parameter...
Page 302: Ip-Fragments-In
To execute the Deny-Notify composite-operation when IP fragmentation packets are received: G350-001(ACL 330)# ip-fragments-in Deny-Notify Related commands cookie, ip-option-in, ip-rule (policy, policy-based routing, packet sniffing), name, owner, show composite-operation, show ip-rule, show list 302 Avaya G250 and Avaya G350 CLI Reference...
Page 303: Ip-Option-In
Alphabetical listing of CLI commands ip-option-in Use the ip-option-in command to specify the treatment of packets carrying an IP option that enter the current interface. Use the no form of the command to return to the default treatment of IP option packets. Syntax ip-option-in action no ip-option-in...
Page 304: Ip-Protocol
To specify that rule 22 applies to all packets having an IP protocol of IGMP: G350-001(ACL 330/ip rule 22)# ip-protocol icmp Related commands destination-ip, dscp (policy, policy-based routing, packet sniffing), icmp, show ip capture-list, source-ip, destination-port, source-port, destination-port, udp source-port 304 Avaya G250 and Avaya G350 CLI Reference...
Page 305: Ip-Rule (Policy, Policy-Based Routing, Packet Sniffing)
Alphabetical listing of CLI commands ip-rule (policy, policy-based routing, packet sniffing) Use the ip-rule command to enter configuration mode for the specified rule. If the specified rule does not exist, the system creates it and enters its configuration mode. Syntax ip-rule {rule_index | default} Parameters Parameter...
Page 306: Ip-Rule (Vpn)
User level read-write Context ip crypto-list Example G350-001(Crypto 901)# ip-rule 21 G350-001(Crypto 901/ip rule 21)# Related commands description (ip rule), destination-ip, crypto-list, local-address, protect crypto map, source-ip, show ip crypto-list 306 Avaya G250 and Avaya G350 CLI Reference...
Page 307: Isakmp-Policy
Alphabetical listing of CLI commands isakmp-policy Use the isakmp-policy command to set the ISAKMP policy for the ISAKMP peer. Use the no form of the command to delete the ISAKMP policy for the ISAKMP peer. Note: You cannot delete an ISAKMP policy that is referenced by an ISAKMP peer that Note: is, in turn, referenced by an active crypto map.
Page 308: Keepalive-Icmp
WAN FastEthernet port. User level read-write Context Interface: FastEthernet Example To enable ICMP keepalive on the FastEthernet 10/2 interface for destination IP address 135.64.2.12 using MAC 11.22.33.44.55.66: G350-001(if:FastEthernet 10/2)# keepalive-icmp 135.64.2.12 11.22.33.44.55.66 308 Avaya G250 and Avaya G350 CLI Reference...
Page 309: Keepalive-Icmp Failure-Retries
Alphabetical listing of CLI commands Related commands keepalive-icmp failure-retries, keepalive-icmp interval, keepalive-icmp source-address, keepalive-icmp success-retries, keepalive-icmp timeout, show keepalive-icmp keepalive-icmp failure-retries Use the keepalive-icmp failure-retries command to set the number of consecutive failed keepalive packets necessary to set the interface’s keepalive status as down. Using this command without a parameter resets the failure-retry value to the default value.
Page 310: Keepalive-Icmp Interval
Use the keepalive-icmp source-address command to set the source IP address of the keepalive packets. Using this command without a parameter sets the source IP address to the default value, which is the interface’s primary IP address. Syntax keepalive-icmp source-address source_ip_address 310 Avaya G250 and Avaya G350 CLI Reference...
Page 311: Keepalive-Icmp Success-Retries
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The source IP address of the source_ip_ keepalive packets interface’s address primary IP address User level read-write Context Interface: FastEthernet Example G350-001(if:FastEthernet 10/2)# keepalive-icmp source-address 149.49.78.96 Related commands keepalive-icmp, keepalive-icmp failure-retries,...
Page 312 CLI Commands User level read-write Context Interface: FastEthernet Example G350-001(if:FastEthernet 10/2)# keepalive-icmp success-retries 2 Related commands keepalive-icmp, keepalive-icmp failure-retries, keepalive-icmp interval, keepalive-icmp timeout, keepalive-icmp source-address, show keepalive-icmp 312 Avaya G250 and Avaya G350 CLI Reference...
Page 313: Keepalive-Icmp Timeout
Alphabetical listing of CLI commands keepalive-icmp timeout Use the keepalive-icmp timeout command to set the timeout (in seconds) for receiving the keepalive response. Using this command without a parameter resets the timeout value to the default value. Syntax keepalive-icmp timeout timeout Parameters Parameter Description...
Page 314: Keepalive-Track
Interface: FastEthernet crypto isakmp peer Example To register a remote VPN peer with an object tracker: G350-001(config-peer:149.49.70.1)# keepalive-track 5 To register the FastEthernet interface with an object tracker: G350-001(config-if:FastEthernet 10/2)# keepalive-track 2 314 Avaya G250 and Avaya G350 CLI Reference...
Page 315: Keepalive (Gre Tunnel)
Alphabetical listing of CLI commands Related commands - VPN description (ISAKMP peer), continuous-channel, crypto isakmp peer, initiate mode aggressive, isakmp-policy, keepalive (VPN), pre-shared-key, self-identity, show crypto isakmp peer, suggest-key keepalive (GRE tunnel) Use the keepalive command in the context of a GRE tunnel to specify that the tunnel sends keepalive packets to determine if the tunnel endpoint is up.
Page 316: Keepalive (Ppp)
Interface: Serial (DS1 PPP L2, DS1 PPP L2-L3, DS1 FR L2, USP PPP L2, USP PPP L2-L3, USP FR L2) Example To enable PPP keepalive, and generate a message every 300 seconds: G350-001(if:Serial 2/1)# keepalive 300 Related commands encapsulation, address, ppp timeout ncp, ppp timeout retry, show interfaces 316 Avaya G250 and Avaya G350 CLI Reference...
Page 317: Keepalive (Vpn)
Alphabetical listing of CLI commands keepalive (VPN) Use the keepalive command in crypto isakmp peer interface context to enable DPD (Dead Peer Detection) keepalives that check whether the remote peer is up. Use the no form of this command to disable DPD keepalives (default setting). Syntax [no] keepalive [seconds [retry retry-seconds] [on-demand | periodic] ] Parameters...
Page 318: Lease
Note: You cannot change the lifetime settings of an ISAKMP policy referenced by an Note: ISAKMP peer that is linked to a crypto map. Syntax [no] lifetime seconds 318 Avaya G250 and Avaya G350 CLI Reference...
Page 319: Line
Alphabetical listing of CLI commands Parameters Parameter Description Possible Values Default Value The number of seconds defining the lifetime 60-86,400 86,400 seconds of the ISAKMP SA (1 min. to 24 hrs) User level read-write Context crypto isakmp policy Example G350-001(config-isakmmp:1)# lifetime 100 Related commands authentication, crypto isakmp...
Page 320: Linecode (E1)
Syntax linecode {ami|hdb3} Parameters Parameter Description Possible Default Values Value Keyword that specifies the Alternate Mode Inversion line-code type Keyword that specifies the High-Density hbd3 Bipolar 3 line-code type User level read-write 320 Avaya G250 and Avaya G350 CLI Reference...
Page 321: Linecode (T1)
Alphabetical listing of CLI commands Context Interface: Controller (E1) Example To set the line-code type to ami: G350-001(controller:5/1)# linecode ami Related commands cablelength long, cablelength short, channel-group, clock source, controller, ds-mode, framing, interface serial, address, linecode (T1), remote, show controllers linecode (T1) Use the linecode command to specify the type of line-code transmission for the a T1 line.
Page 322: Load-Interval
Interface: Serial (DS1 PPP L2-L3, DS1 PPP L2, DS1 FR L2, USP PPP L2-L3, USP PPP L2, USP FR L2), FastEthernet (L2, L2-L3), VLAN (L2-L3, L2), Loopback (L2-L3, L2), Tunnel (L2, L2-L3) Example To set the load calculation interval to 60 seconds: G350-001(if:Serial 2/1:1)# load-interval 60 322 Avaya G250 and Avaya G350 CLI Reference...
Page 323: Local-Address
Alphabetical listing of CLI commands Related commands description (interface), interface Console, interface FastEthernet, interface Loopback, interface serial, interface tunnel, interface usb, interface vlan, address, admin-state, broadcast-address, show ip interface brief local-address Use the local-address command to set the local IP address for the IPSec tunnels derived from this crypto-list.
Page 324: Loopback Diag
Use the loopback local command to activate a Loopback signal on the Serial interface. Use the no form of the command to deactivate the Loopback signal. Syntax loopback local loopback_type no loopback local 324 Avaya G250 and Avaya G350 CLI Reference...
Page 325: Loopback Remote
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The type of information to loop back line, loopback_type payload User level read-write Context Interface: Controller Example To activate a loopback signal with payload information: G350-001(if:Serial 5/1)# loopback local payload Related commands loopback diag,...
Page 326: Map-Class Frame-Relay
This command fails if the map class is currently associated with a DLCI. Note: Syntax [no] map-class frame-relay map_class_name Parameters Parameter Description Possible Default Values Value The name of a map class configured by the user map_class_name User level read-write Context general 326 Avaya G250 and Avaya G350 CLI Reference...
Page 327: Mode
Alphabetical listing of CLI commands Example To create a map class named mySVoip1: G350-001(super)# map-class frame-relay mySVoip1 G350-001(super-map-class)# Related commands clear frame-relay counters, frame-relay class-dlci, interface serial, show frame-relay map, show frame-relay pvc brief, show interfaces mode Use the mode command to set the IPSec encapsulation mode. Use the no form of the command to return the value to the default encapsulation mode, which is tunnel mode.
Page 328: Mtu
G350-001(if:Serial 2/1:1)# mtu 1000 Related commands - PPPOE encapsulation pppoe, ppp chap hostname, ppp chap password, ppp pap-sent username, pppoe-client persistent delay, pppoe-client persistent max-attempts, pppoe-client service-name, pppoe-client wait-for-ipcp, show ppp authentication 328 Avaya G250 and Avaya G350 CLI Reference...
Page 329: Name
Alphabetical listing of CLI commands name Use the name command to assign a name to the specified list or operation. Use the no form of the command to return the name to the default value. Syntax [no] name name Parameters Parameter Description Possible Values...
Page 330: Name-Server
DNS servers from the list Keyword indicating to delete all dynamic dynamic DNS servers from the list Keyword indicating to delete all static static DNS servers from the list User level read-write Context ip domain name-server-list 330 Avaya G250 and Avaya G350 CLI Reference...
Page 331: Network (Rip)
Alphabetical listing of CLI commands Example To add the DNS server with IP address 1.1.1.1 as the second server in list 1: G350-001(name-server-list:1)# name-server 2 1.1.1.1 To delete all static DNS servers from list 1: G350-001(name-server-list:1)# no name-server static Related commands clear ip domain statistics, description (DNS...
Page 332: Network (Ospf)
To enable OPSF on the range of IP addresses from 192.168.0.0 to 192.168.255.255 in area ID 0.0.0.0: G350-001(router:ospf)# network 192.168.0.0 0.0.255.255 area 0.0.0.0 Related commands area, default-metric (OSPF), passive-interface, redistribute (OSPF), timers spf 332 Avaya G250 and Avaya G350 CLI Reference...
Page 333: Next-Hop (Policy-Based Routing)
Alphabetical listing of CLI commands next-hop (policy-based routing) Use the next-hop command to specify the next-hop policy to use when the current rule is applied. Syntax next-hop {list list_number | DBR} Parameters Parameter Description Possible Default Values Value Keyword indicating that a list next-hop list will be specified to be used for the current rule...
Page 334: Next-Hop (Object Tracking)
Applies to Ethernet interfaces only: FastEthernet not running PPPoE VLAN User level read-write Context rtr type Examples G350-001(config-rtr icmp 1)# next-hop FastEthernet 10/2 interface-name 00:04:d0:af:12:4 mac-address G350-001(config-rtr icmp 1)# next-hop Serial 2/1:1 interface-name 334 Avaya G250 and Avaya G350 CLI Reference...
Page 335: Next-Hop-Interface
Alphabetical listing of CLI commands Related commands dscp (object tracking), fail-retries, frequency, interface-keepalive bypass-logic, rtr, source-address, success-retries, type, wait-interval next-hop-interface Use the next-hop-interface command to add the specified interface to the next hop path for this next-hop list. Use the no form of this command to delete an interface from the next-hop list.
Page 336: Next-Hop-Ip
The index in the array of 1-20 hop_number next-hops belonging to the specific next-hop-list The specified next-hop IP ip_address address User level read-write Context ip next-hop-list Example G350-001(super)# next-hop-ip 2 149.49.200.2 Related commands next-hop-interface, show next-hop 336 Avaya G250 and Avaya G350 CLI Reference...
Page 337: Next-Server
Alphabetical listing of CLI commands next-server Use the next-server command to specify the IP address of the next server in the boot process of a DHCP client. Use the no form of this command to clear the next server IP address. Syntax [no] next-server ip-address Parameters...
Page 338: Nrzi-Encoding
Use the nslookup command to resolve a host name to an IP address. Note: The nslookup command has a timeout of 30 seconds. Note: Syntax nslookup hostname Parameters Parameter Description Possible Values Default Value The host name hostname User level read only Context general 338 Avaya G250 and Avaya G350 CLI Reference...
Page 339: Nvram Initialize
Alphabetical listing of CLI commands Example G350-001(super)# nslookup www.avaya.com DNS server : 135.64.19.81 Host name : pcmsnj.avaya.com IP address : 216.74.135.14 Host alias : www.avaya.com pcms.avaya.com Related commands clear ip domain statistics, ip domain list, ip domain lookup, ip domain...
Page 340: Object
Possible Values Default Value The object tracker ID 1-50 track-id User level read-write Context track list Example G350-001(config-track list 2)# object 3 Related commands description (object tracking), threshold count, track, show track 340 Avaya G250 and Avaya G350 CLI Reference...
Page 341 Alphabetical listing of CLI commands option Use the option command to create a DHCP general option or to enter the context of a DHCP general option. Use the no form of this command to clear a DHCP general option. Syntax [no] option option-num Parameters Parameter...
Page 342: Owner
(policy, policy-based routing, packet sniffing), name, show ip-rule, show list Related commands - Policy composite-operation, cookie, dscp-table, ip-fragments-in, ip-option-in, ip-rule (policy, policy-based routing, packet sniffing), name, show composite-operation, show ip-rule, show list 342 Avaya G250 and Avaya G350 CLI Reference...
Page 343: Passive-Interface
Alphabetical listing of CLI commands passive-interface Use the passive-interface command to suppress OSPF routing updates on the interface. Syntax passive-interface {interface_name | net_address} Parameters Parameter Description Possible Default Values Value Name of the interface on which to suppress interface_name routing updates IP address of the interface on which to net_address suppress routing updates...
Page 344: Ping
Context general Example To send test 50-byte packets to IP address 192.168.49.1 from IP address 192.168.49.4 every three seconds, timing out after five seconds: G350-001(super)# ping 192.168.49.1 3 50 5 192.168.49.4 344 Avaya G250 and Avaya G350 CLI Reference...
Page 345: Pmi
Alphabetical listing of CLI commands Use the pmi command to define this interface as the Primary Management Interface for the system. Syntax User level read-write Context Interface: Serial (DS1 PPP L2-L3, DS1 PPP L3, DS1 FR-SUB L2-L3, DS1 FR-SUB L3, USP PPP L3, USP PPP L2-L3), FastEthernet (L2-L3, L3), VLAN (L2-L3, L3), Loopback (L2-L3, L3), Tunnel (L2-L3, L3) Example...
Page 346: Ppp Chap Hostname
(PPP), timeout absolute ppp chap hostname Use the ppp chap hostname command to override the device hostname for PPP CHAP authentication. Syntax ppp chap hostname string no ppp chap hostname 346 Avaya G250 and Avaya G350 CLI Reference...
Page 347: Ppp Chap Password
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value string The username assigned by the broadband internet service provider User level Read-write Context Interface: Fast Ethernet Example G350-001(super-if:FastEthernet 10/2)# ppp chap hostname avaya32 Related commands encapsulation pppoe, mtu, ppp chap password, ppp pap-sent...
Page 348: Ppp Chap Refuse
Syntax ppp chap refuse no ppp chap refuse User level Read-write Context Interface: Fast Ethernet Example G350-001(super-if:FastEthernet 10/2)# ppp chap refuse Related commands interface FastEthernet, ppp pap refuse 348 Avaya G250 and Avaya G350 CLI Reference...
Page 349: Ppp Chap-Secret
Alphabetical listing of CLI commands ppp chap-secret Use the ppp chap-secret command to configure the shared secret used in PPP sessions with CHAP authentication. Note: The value set for ppp chap-secret affects both the USB interface and the Note: Console interface, simultaneously. Syntax ppp chap-secret chap_secret Parameters...
Page 350: Ppp Ipcp Dns Request
Use the ppp pap refuse command to prevent authentication with PAP, even when a pap-sent password is configured. Syntax ppp pap refuse no ppp pap refuse User level Read-write Context Interface: Fast Ethernet 350 Avaya G250 and Avaya G350 CLI Reference...
Page 351: Ppp Pap-Sent Username
Alphabetical listing of CLI commands Example G350-001(super-if:FastEthernet 10/2)# ppp pap refuse Related commands interface FastEthernet, ppp chap refuse ppp pap-sent username Use the ppp pap-sent username command to set the Password Authentication Protocol (PAP) password for authentication with the remote peer. Note: Executing the copy running-config startup-config command stores Note:...
Page 352: Ppp Timeout Ncp
Interface: Serial (DS1 PPP L2-L3, DS1 PPP L2, USP PPP L2-L3, USP PPP L2) Example To specify that PPP will allow 60 seconds for negotiation of a network protocol: G350-001(super)# ppp timeout ncp 60 Related commands encapsulation, address, keepalive (PPP), ppp timeout retry, show interfaces 352 Avaya G250 and Avaya G350 CLI Reference...
Page 353: Ppp Timeout Retry
Alphabetical listing of CLI commands ppp timeout retry Use the ppp timeout retry command to set the maximum time to wait for a response during PPP negotiation. Use the no form of the command to restore the timeout value to its default.
Page 354: Pppoe-Client Persistent Max-Attempts
To restart the connection attempts, use the shutdown and no shutdown command sequence. Syntax pppoe-client persistent max-attempts number no pppoe-client persistent max-attempts Parameters Parameter Description Possible Default Values Value The number of attempts. 0-10000 0 (no limit) number 354 Avaya G250 and Avaya G350 CLI Reference...
Page 355: Pppoe-Client Service-Name
Alphabetical listing of CLI commands User level Read-write Context Interface: Fast Ethernet Example G350-001(super-if:FastEthernet 10/2)# pppoe-client persistent max-attempts 0 Related commands encapsulation pppoe, mtu, ppp chap hostname, ppp chap password, ppp pap-sent username, pppoe-client persistent delay, pppoe-client service-name, pppoe-client wait-for-ipcp, show ppp authentication pppoe-client service-name...
Page 356: Pppoe-Client Wait-For-Ipcp
Parameters Parameter Description Possible Default Values Value The number of seconds to wait 5-10000 seconds User level Read-write Context Interface: Fast Ethernet Example G350-001(super-if:FastEthernet 10/2)# pppoe-client wait-for-ipcp 30 356 Avaya G250 and Avaya G350 CLI Reference...
Page 357: Pre-Classification
Alphabetical listing of CLI commands Related commands encapsulation pppoe, mtu, ppp chap hostname, ppp chap password, ppp pap-sent username, pppoe-client persistent delay, pppoe-client persistent max-attempts, pppoe-client service-name, show ppp authentication pre-classification Use the pre-classification command to specify which priority tag the current QoS list uses for data flows.
Page 358: Pre-Shared-Key
Examples G350-001(config-peer:149.49.70.1)# pre-shared-key GNpi1odGNBrB5z4GJLzI G350-001(config-peer:149.49.70.1)# pre-shared-key 616263 hexadecimal Related commands description (ISAKMP peer), continuous-channel, crypto isakmp peer, initiate mode aggressive, isakmp-policy, keepalive (VPN), keepalive-track, self-identity, show crypto isakmp peer, suggest-key 358 Avaya G250 and Avaya G350 CLI Reference...
Page 359: Priority-Queue
Alphabetical listing of CLI commands priority-queue Use the priority-queue command to enable priority queuing mode in a serial or Fast Ethernet interface. By default, priority queuing is off, and Weighted Fair VoIP Queuing (WFVQ) is enabled on all Serial interfaces and all Fast Ethernet interfaces for which traffic-shaping is enabled.
Page 360: Protect Crypto Map
Context crypto map/ip-rule Examples G350-001(crypto 901/ip rule 21)# protect crypto map 5 G350-001(crypto 901/ip rule 22)# no protect Related commands description (ip rule), destination-ip, crypto-list, ip-rule (VPN), local-address, source-ip, show ip crypto-list 360 Avaya G250 and Avaya G350 CLI Reference...
Page 361: Queue-Limit
Alphabetical listing of CLI commands queue-limit Use the queue-limit command to set the packet size of the various queues. Use the no form of the command to restore the packet size to its default value, using the interface bandwidth. Note: The queue-limit command is not applicable in fair-voip-queue mode.
Page 362: Redistribute (Rip)
(interface route metric value) redistribute (OSPF) Use the redistribute command to redistribute routing information from other protocols into OSPF. Use the no form of this command to disable redistribution by OSPF. Syntax [no] redistribute protocol 362 Avaya G250 and Avaya G350 CLI Reference...
Page 363: Release Dhcp
Alphabetical listing of CLI commands Parameters Parameter Description Possible Values Default Value The protocol to be used static, connected, rip protocol User level read-write Context Router: ospf Example To redistribute static routing information into OSPF: G350-001(router:ospf)# redistribute static Related commands - OSPF area, default-metric (OSPF),...
Page 364: Release Voip-Dsp
Status changes that occur during the test create SNMP traps. Note: Note: View the results of the most recent BTR test with the show mm command (refer Note: show mm on page 653). Syntax release voip-dsp User level read-write 364 Avaya G250 and Avaya G350 CLI Reference...
Page 365: Remote
Alphabetical listing of CLI commands Context general Related commands busyout voip-dsp, show show voip-parameters, test voip-dsp remote Use the remote command to reset the far end counters on a T1 line. Syntax remote fdl_request_type Parameters Parameter Description Possible Values Default Value The type of reset-performance-monitoring-counters...
Page 366: Remove Trunk-Group
Use the remove trunk-group command to remove a port from a trunk group in the SLS data set on the G250. The port must belong to a trunk group before you can remove it. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 367: Renew Dhcp
Alphabetical listing of CLI commands renew dhcp Use the renew dhcp command to renew a DHCP lease for an interface. This is effectively a request to renew an existing IP address, or the start of a new process of requesting a new IP address.
Page 368: Reset
Context general Example To reset the VoIP engine: G350-001(super)# reset voip This command will perform a hard reset. Do you want to continue (Y/N)? y Related commands exit, logout, show logout 368 Avaya G250 and Avaya G350 CLI Reference...
Page 369: Retstatus
Alphabetical listing of CLI commands retstatus Use the retstatus command to show whether or not the last CLI command you performed was successful. Syntax retstatus User level read-only Context general Example To display the status of the most recently executed command: G350-001(super)# retstatus Succeeded G350-001(super)# retstatus...
Page 370 G350-003(super)# rmon alarm 1 1.3.6.1.2.1.16.1.1.1.5.16777216 20 delta rising-threshold 10000 32 falling-threshold 1000 32 risingOrFalling root alarm 1 was created successfully Related commands rmon event, rmon history, show rmon alarm, show rmon event, show rmon history, show rmon statistics 370 Avaya G250 and Avaya G350 CLI Reference...
Page 371: Rmon Event
Alphabetical listing of CLI commands rmon event Use the rmon event command to create an RMON event entry. The RMON event can then be triggered as part of an RMON alarm. To create an RMON alarm, refer to rmon alarm page 369.
Page 372: Rmon History
G350-001(super)# rmon history 32 10/2 interval 20 buckets 100 owner config history index 32 was created successfully Related commands rmon alarm, rmon event, show rmon alarm, show rmon event, show rmon history, show rmon statistics 372 Avaya G250 and Avaya G350 CLI Reference...
Page 373: Router Ospf
Alphabetical listing of CLI commands router ospf Use the router ospf command to enable OSPF protocol on the system and to enter the router configuration context. Use the no form of this command to restore the default value, and disable OSPF globally. Syntax [no] router ospf User level...
Page 374: Router Vrrp
RTP echo port to its default. Syntax rtp-echo-port port Parameters Parameter Description Possible Default Values Value The UDP port number to be used as the RTP echo 1-65535 8888 port port number 374 Avaya G250 and Avaya G350 CLI Reference...
Page 375: Rtp-Stat Clear
Alphabetical listing of CLI commands User level read-write Context cna-testplug Example To set the RTP echo port to port 45230: G350-001(cna-testplug 1)# rtp-echo-port 45230 Related commands clear counters (CNA test plugs), cna-testplug, cna-testplug-service, control-port, rtp-test-port, scheduler, show cna testplug, shutdown (CNA test plugs), test-rate-limit rtp-stat clear...
Page 376: Rtp-Stat Event-Threshold
Sets the event threshold for the echo-return-loss metric loss Sets the event threshold for the loss metric remote-loss Sets the event threshold for the remote-loss metric Sets the event threshold for the rtt metric 376 Avaya G250 and Avaya G350 CLI Reference...
Page 377 Alphabetical listing of CLI commands Parameter Description Possible Values Default Value jitter Sets the event threshold for the jitter metric remote-jitter Sets the event threshold for the remote-jitter metric ssrc-change Sets the event threshold for the ssrc-change metric The number of events User level read-write Context...
Page 378: Rtp-Stat Fault
The clear trap boundary was set to 0 Related commands rtp-stat clear, rtp-stat event-threshold, rtp-stat min-stat-win, rtp-stat qos-trap, rtp-stat qos-trap-rate-limit, rtp-stat service, rtp-stat threshold, show rtp-stat config, show rtp-stat detailed, show rtp-stat sessions, show rtp-stat summary, show rtp-stat thresholds 378 Avaya G250 and Avaya G350 CLI Reference...
Page 379: Rtp-Stat Min-Stat-Win
Alphabetical listing of CLI commands rtp-stat min-stat-win Use the rtp-stat min-stat-win command to set the minimum statistic window for the RTP statistics application. The minimum statistics window is the minimum number of observed RTP sequence increments for which the application evaluates packet loss. Use the no form of this command to reset the minimum statistic window to its default value.
Page 380: Rtp-Stat Qos-Trap
The RTP statistics QoS trap is disabled. Related commands rtp-stat clear, rtp-stat event-threshold, rtp-stat fault, rtp-stat min-stat-win, rtp-stat qos-trap-rate-limit, rtp-stat service, rtp-stat threshold, show rtp-stat config, show rtp-stat detailed, show rtp-stat sessions, show rtp-stat summary, show rtp-stat thresholds 380 Avaya G250 and Avaya G350 CLI Reference...
Page 381: Rtp-Stat Qos-Trap-Rate-Limit
Alphabetical listing of CLI commands rtp-stat qos-trap-rate-limit Use the rtp-stat qos-trap-rate-limit command to configure the QoS trap rate limiter. The trap rate limiter limits the rate at which QoS traps are sent to the SNMP trap manager on the MGC. The trap rate limiter uses a token bucket scheme, in which traps are sent only if there are tokens in a virtual bucket.
Page 382: Rtp-Stat Service
QoS trap (if QoS traps are configured) if one or more of them is over its corresponding threshold. See also rtp-stat event-threshold on page 376. 382 Avaya G250 and Avaya G350 CLI Reference...
Page 383 Alphabetical listing of CLI commands Syntax rtp-stat threshold {codec-loss|average-codec-loss|loss|average-loss|remote-loss|average-r emote-loss} percentage rtp-stat threshold {codec-rtt|rtt|jitter|remote-jitter} milliseconds rtp-stat threshold echo-return-loss dbm no rtp-stat threshold {all|codec-loss|average-codec-loss|codec-rtt|echo-return-loss|loss|ave rage-loss|remote-loss|average-remote-loss|rtt|jitter|remote-loss|echo- return-loss} Parameters Parameter Description Possible Default Values Value The percentage of time the codec plays codec-loss fill frames due to lack of valid RTP frames.
Page 384 G350-001(super)# rtp-stat threshold echo-return-loss 5 Related commands rtp-stat clear, rtp-stat event-threshold, rtp-stat fault, rtp-stat min-stat-win, rtp-stat qos-trap, rtp-stat qos-trap-rate-limit, rtp-stat service, show rtp-stat config, show rtp-stat detailed, show rtp-stat sessions, show rtp-stat summary, show rtp-stat thresholds 384 Avaya G250 and Avaya G350 CLI Reference...
Page 385: Rtp-Test-Port
Alphabetical listing of CLI commands rtp-test-port Use the rtp-test-port command to set the UDP port used by the CNA test plug to send an RTP stream to another test plug in an RTP test. Use the no form of the command to return to default UDP port for RTP tests.
Page 386: Rtr
Parameters Parameter Description Possible Values Default Value The RTR ID 1-30 rtr-id User level read-write Context general Example G350-001(config)# rtr 1 Related commands rtr-schedule, show rtr configuration, show rtr operational-state, type 386 Avaya G250 and Avaya G350 CLI Reference...
Page 387: Rtr-Schedule
Use the sat command to provide a shortcut method to access the System Access Terminal (SAT) so that Avaya Communication Manager translation work can be performed. See the description for session on page 392 for more information. The Media Server must configure the SAT port to 5023.
Page 388: Save Config
User level read-only Context general save config Use the save config command to write the SLS data set in a G250 to non-volatile RAM (NVRAM). Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 389: Scheduler
Alphabetical listing of CLI commands scheduler Use the scheduler command to add a scheduler’s IP address to the list of schedulers with which the test plug can attempt to register. You can list up to five schedulers. The test plug attempts to register with the scheduler highest on the list, and moves along the list if necessary until registration is successful.
Page 390: Self-Identity
[no] self-identity {address | fqdn fqdn-str} Note: Specify the self-identity in FQDN format when using aggressive mode. Note: Note: If the remote ISAKMP peer is an Avaya Security Gateway (VSU / SG), you must Note: specify the self-identity FQDN using upper-case letters only. Parameters Parameter...
Page 391: Server-Name
User level read-write Context dhcp pool Example To set the optional server name to “avaya”: G350-001(DHCP 5)# server-name "avaya" To clear the optional server name: G350-001(DHCP 5)# no server-name Related commands bootfile, client-identifier, default-router, dns-server, domain-name, end-ip-addr, lease, name,...
Page 392: Session
To establish a session with the active Media Gateway Controller: G350-001(super)# session mgc Related commands clear mgc list, icc-monitoring, mediaserver, set mgc list, reset-times, show icc-monitoring, show mediaserver, show mgc, show mgc list 392 Avaya G250 and Avaya G350 CLI Reference...
Page 393: Set Ars-Fac
Use the set ars-fac command to configure up to two Automatic Route Selection (ARS) Feature Access Codes (FACs) in the SLS data on the G250. ARS FACs must be unique from any extension or Trunk Access Code (TAC).
Page 394: Set Boot Bank
SW_imageA, copy ftp SW_imageB, copy tftp EW_archive, copy tftp module, copy tftp SW_imageA, copy tftp SW_imageB, dir, show boot bank, show download software status, show image version 394 Avaya G250 and Avaya G350 CLI Reference...
Page 395: Set Contact-Closure Admin
Alphabetical listing of CLI commands set contact-closure admin Use the set contact-closure admin command to specify how the contact closure relay is controlled. Note: The set contact-closure pulse-duration command does not affect the Note: set contact-closure admin manual command. Syntax set contact-closure admin module/port:relay {mgc | manual-trigger | manual-off} Parameters...
Page 396: Set Contact-Closure Pulse-Duration
Example To set the pulse duration to 3 seconds for relay 2 of port 1 on module 10: G350-001(super)# set contact-closure pulse-duration 10/1:2 3 Related commands set contact-closure admin, show contact-closure 396 Avaya G250 and Avaya G350 CLI Reference...
Page 397: Set Date-Format
Alphabetical listing of CLI commands set date-format Use the set date-format command to set a date format for the SLS data set on the G250. The default date format is mm/dd/yy. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 398 You must be in the survivable-call-engine context before the set dial-pattern command will work. Example G250-001(super-survivable-call-engine)# set dial-pattern 49139 10 locl false 22 Dialed String: 49139 Length: 10 Type: locl Deny Call: false Trunk Group: 398 Avaya G250 and Avaya G350 CLI Reference...
Page 399: Set Dot1X Max-Req
Alphabetical listing of CLI commands Related commands trunk-group, clear ars-fac, clear survivable-config, clear dial-pattern, clear extension, clear trunk-group, remove trunk-group, save config, ars-fac, date-format, extension, extension-password, ip-codec-set, max-ip-registrations, survivable-call-engine, trunk-group, show ars-fac, show date-format, show dial-pattern, show extension, show ip-codec-set, show last-pim-update, show...
Page 400: Set Dot1X Quiet-Period
400 Avaya G250 and Avaya G350 CLI Reference...
Page 401: Set Dot1X Re-Authperiod
Alphabetical listing of CLI commands set dot1x re-authperiod Use the set dot1x re-authperiod command to set the idle time between re-authentication attempts. Note: Time period settings affect all external ports. Note: Syntax set dot1x re-authperiod seconds Parameters Parameter Description Possible Default Value Values Number of seconds...
Page 402: Set Dot1X Server-Timeout
402 Avaya G250 and Avaya G350 CLI Reference...
Page 403: Set Dot1X Supp-Timeout
Alphabetical listing of CLI commands set dot1x supp-timeout Use the set dot1x supp-timeout command to set the maximum time that the switch will wait for a reply from the Authenticated Station before the session is terminated. Note: Timeout settings affect all external ports. Note: Syntax set dot1x supp-timeout seconds...
Page 404: Set Dot1X System-Auth-Control Disable
Use the set dot1x system-auth-control enable command to globally enable the PBNAC (802.1x) feature. Syntax set dot1x system-auth-control enable User Level admin Context general 404 Avaya G250 and Avaya G350 CLI Reference...
Page 405: Set Dot1X Tx-Period
Alphabetical listing of CLI commands Example G350-001(super)# set dot1x system-auth-control enable Related commands clear dot1x config, set dot1x max-req, set dot1x quiet-period, set dot1x re-authperiod, set dot1x server-timeout, set dot1x supp-timeout, set dot1x system-auth-control disable, set dot1x tx-period, set port dot1x initialize, set port dot1x port-control,...
Page 406: Set Dscp
DSCP is copied from the DS field of the original packet. User level read-write Context crypto map Examples G350-001(config-crypto:1)# set dscp 10 G350-001(config-crypto:1)# no set dscp Related commands continuous-channel, description (crypto map), set peer (crypto map), peer-group, transform-set 406 Avaya G250 and Avaya G350 CLI Reference...
Page 407: Set Etr
Alphabetical listing of CLI commands set etr Use the set etr command to enable or disable Emergency Transfer Relay (ETR) mode, or to allow the gateway to control ETR mode automatically. Note: In ETR mode, the TRK and LINE 1 ports are connected. All other telephone ports Note: stop operating.
Page 408: Set Extension
You must assign a password to the extension if the port is ip. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Syntax set extension extension type port cor trunk-dest...
Page 409: Set Extension-Password
Use the set extension-password command to set passwords for IP endpoints. If the port is ip, you must assign a password. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 410: Set Icc-Monitoring
Use the set icc-monitoring command to control heartbeat monitoring of an Inter Carrier Cable (ICC) or Local Survivable Processor (LSP). Syntax set icc-monitoring {enable | disable} Parameters Parameter Description Possible Default Values Value Enable heartbeat monitoring enable Disable heartbeat monitoring disable 410 Avaya G250 and Avaya G350 CLI Reference...
Page 411: Set Ip-Codec-Set
Use the set ip-codec-set command to configure an IP codec set within the SLS data set on the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Note:...
Page 412: Set Lldp Re-Init-Delay
Value The delay in seconds from when a port is set to 1-10 value LLDP "disable" until re-initialization will be attempted User level read-write Context General Example G250-001(super)# set lldp re-init-delay 5 412 Avaya G250 and Avaya G350 CLI Reference...
Page 413: Set Lldp System-Control
Values Value Enable the LLDP application enable Disable the LLDP application disable User level read-write Context General Example G250-001(super)# set lldp system-control enable Related commands set lldp re-init-delay, set lldp tx-delay, set lldp tx-hold-multiplier, set lldp tx-interval, set port lldp,...
Page 414: Set Lldp Tx-Delay
The tx delay should be in the range 1 <= TxDelay <= (0.25 * TxInterval) This transmission rate limiting applies only to situations caused by asynchronous transmission or shutdown when the LLDP application is stopped on a port or system in an Avaya device. Syntax...
Page 415: Set Lldp Tx-Hold-Multiplier
Description Possible Default Values Value The multiplier 2-10 number User level read-write Context General Example G250-001(super)# set lldp tx-hold-multiplier 4 Related commands set lldp re-init-delay, set lldp system-control, set lldp tx-delay, set lldp tx-interval, set port lldp, set port lldp...
Page 416: Set Lldp Tx-Interval
Use the set logging file command to manage the logging of system messages to non-volatile memory (NVRAM). Syntax set logging file {enable | disable | condition {all | MsgFacility} {none | severity}} 416 Avaya G250 and Avaya G350 CLI Reference...
Page 417 Alphabetical listing of CLI commands Parameters Parameter Description Possible Values Default Value Enable logging to the file enable sink Disable logging to the file disable sink Define a filter rule for condition logging Apply the filter condition to all MsgFacilities Apply the filter condition to boot, dialer, policy, MsgFacility...
Page 418: Set Logging Server
418 Avaya G250 and Avaya G350 CLI Reference...
Page 419: Set Logging Server Access-Level
Alphabetical listing of CLI commands set logging server access-level Use the set logging server access-level command to define the access level associated with a Syslog server sink. You cannot specify an admission level higher than the assigned level. Syntax set logging server access-level admission_level {ip_address | hostname} Parameters Parameter Description...
Page 420: Set Logging Server Condition
(0 is the alert (1), highest severity, 7 the critical (2), lowest) error (3), warning (4), notification (5), informational (6), debugging (7) The IP address of the Syslog ip_address server User level read-write 420 Avaya G250 and Avaya G350 CLI Reference...
Page 421: Set Logging Server Enable/Disable
Alphabetical listing of CLI commands Context general Example To filter fan messages for the Syslog server at IP address 168.23.1.15, so that only fan messages of warning-level severity or greater are sent: G350-001(super)# set logging server condition fan warning 168.23.1.15 Related commands clear logging file,...
Page 422: Set Logging Server Facility
(Log Alert), audi (Log Audit), ntp (NTP Subsystem), lpr (Printing), sec (Security), syslog (System Logging), uucp (Unix-to-Unix Copy Program), news (Usenet news), user (User Process) The IP address of ip_address the Syslog server 422 Avaya G250 and Avaya G350 CLI Reference...
Page 423: Set Logging Session
Alphabetical listing of CLI commands User level read-write Context general Example To specify that messages for the specified Syslog server be sent to the mail output facility: G350-001(super)# set logging server facility mail 168.12.1.15 Related commands clear logging file, clear logging server, set logging file,...
Page 424 424 Avaya G250 and Avaya G350 CLI Reference...
Page 425: Set Logout
Alphabetical listing of CLI commands set logout Use the set logout command to set the number of minutes until the system automatically disconnects an idle session. Syntax set logout [timeout] Parameters Parameter Description Possible Default Values Value Number of minutes until the system 0-99 timeout automatically disconnects an idle session.
Page 426: Set Max-Ip-Registrations
Use the set max-ip-registrations command to configure the maximum IP registrations allowed in the SLS data set on the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 427: Set Mediaserver
Alphabetical listing of CLI commands set mediaserver Use the set mediaserver command to set media server management ports. Syntax set mediaserver ip_address1 ip_address2 port name Parameters Parameter Description Possible Default Values Value Controller IP address used for registration ip_address1 Management interface IP address ip_address2 Service port number port...
Page 428: Set Mgc List
To specify two Media Gateway Controllers at IP addresses 132.236.73.2 and 119.52.3.27: G350-001(super)# set mgc list 132.236.73.2, 119.52.3.27 Related commands clear mgc list, session, icc-monitoring, mediaserver, reset-times, show icc-monitoring, show mediaserver, show mgc, show mgc list 428 Avaya G250 and Avaya G350 CLI Reference...
Page 429: Set Peer (Crypto Map)
Alphabetical listing of CLI commands set peer (crypto map) Use the set peer command to attach a peer to a crypto map. Use the no form of the command to remove the peer from the crypto map. Note: You can only change the peer of a crypto map when the map is inactive. Note: Note: The set peer and set peer-group commands are mutually exclusive.
Page 430: Set Peer (Peer Group)
User level read-write Context crypto isakmp peer-group Examples G350-001(config-peer-grp:vpn.avaya.com)# set peer 149.49.52.135 1 Related commands crypto isakmp peer-group, description (ISAKMP peer group), show crypto isakmp peer-group 430 Avaya G250 and Avaya G350 CLI Reference...
Page 431: Set Peer-Group
Parameter Description Possible Default Values Value The name of the peer-group peer-group-name User level read-write Context crypto map Examples G350-001(config-crypto:1)# set peer-group vpn.avaya.com Related commands continuous-channel, crypto map, description (crypto map), transform-set, dscp, set peer (crypto map), show crypto map...
Page 432: Set Pfs
Specifies that IKE employs the 2048-bit group14 Diffie-Hellman prime modulus group. User level read-write Context crypto ipsec transform-set Example G350-001(config-transform:ts1)# set pfs group1 Related commands crypto ipsec transform-set, mode, set security-association lifetime, show crypto ipsec transform-set 432 Avaya G250 and Avaya G350 CLI Reference...
Page 433: Set Port Auto-Negotiation-Flowcontrol-Advertisement
Alphabetical listing of CLI commands set port auto-negotiation-flowcontrol-advertisement Use the set port auto-negotiation-flowcontrol-advertisement command to set the flowcontrol advertisement for the specified port when performing autonegotiation. Syntax set port auto-negotiation-flowcontrol-advertisement module/port {no-flowcontrol|asym-tx-only|sym-only|sym-and-asym-rx} Parameters Parameter Description Possible Default Values Value Number of the module module Number of the port on the module.
Page 434: Set Port Classification
User level read-write Context general Example To set the port classification for port 3 of module 5 to valuable: G350-001(super)# set port classification 5/3 valuable Port 5/3 classification has been changed. 434 Avaya G250 and Avaya G350 CLI Reference...
Page 435: Set Port Disable
Alphabetical listing of CLI commands Related commands show port classification set port disable Use the set port disable command to disable a port or range of ports. Syntax set port disable module/port Parameters Parameter Description Possible Default Values Value Number of the module module Number of the port on the module.
Page 436: Set Port Dot1X Initialize
436 Avaya G250 and Avaya G350 CLI Reference...
Page 437: Set Port Dot1X Port-Control
Alphabetical listing of CLI commands set port dot1x port-control Use the set port dot1x port-control command to set the dot1x parameter per port. Syntax set port dot1x port-control mod/port {force-authorize | force-unauthorize | auto} Parameters Parameter Description Possible Default Values Value Number of the module Number of the port on the...
Page 438: Set Port Dot1X Re-Authenticate
438 Avaya G250 and Avaya G350 CLI Reference...
Page 439: Set Port Dot1X Re-Authentication
Alphabetical listing of CLI commands set port dot1x re-authentication Use the set port dot1x re-authentication command to set the re-authentication mode per port. Syntax set port dot1x re-authentication mod/port {enable | disable} Parameters Parameter Description Possible Default Value Values Number of the module Number of the port on the port module...
Page 440: Set Port Duplex
440 Avaya G250 and Avaya G350 CLI Reference...
Page 441: Set Port Edge Admin State
Use the set port edge admin state command to specify whether or not a port is considered to be an edge port. Note: This command is not supported by the G250. Note: Syntax set port edge admin state module/port admin_state...
Page 442: Set Port Enable
442 Avaya G250 and Avaya G350 CLI Reference...
Page 443: Set Port Flowcontrol
Alphabetical listing of CLI commands set port flowcontrol Use the set port flowcontrol command to set the send/receive mode for flow-control frames (IEEE 802.3x or proprietary) for a full duplex port. Each direction (send or receive) can be configured separately. Syntax set port flowcontrol {receive | send | all} module/port {off | on | proprietary}...
Page 444 444 Avaya G250 and Avaya G350 CLI Reference...
Page 445: Set Port Level
Alphabetical listing of CLI commands set port level Use the set port level command to set the priority level of a port or range of ports on the switching bus. Packets traveling through a port set at normal priority are served only after packets traveling through a port set at high priority are served.
Page 446: Set Port Lldp
446 Avaya G250 and Avaya G350 CLI Reference...
Page 447: Set Port Lldp Tlv
Alphabetical listing of CLI commands set port lldp tlv Use the set port lldp tlv command to enable or disable the transmission of the optional TLVs on a per port basis. The optional TLVs are: Port description System name System description System capabilities Management address Port-vlan-id...
Page 448 TLVs, you should execute the command for different tlv_names, or once with tlv_name=all. When using the “all” option, the VLAN-Name TLVs are sent indicating all VLANs bound to each port. User level read-write Context general Example G250-001(super)# set port lldp 10/3 rx-and-tx 448 Avaya G250 and Avaya G350 CLI Reference...
Page 449: Set Port Mirror
4/5-13 for ports 5 to 13 on module 4 in the G350, or 10/3-5 for ETH LAN ports 3-5 on the front panel of the G250. Specifies whether to allow or disable always, sampling_...
Page 450: Set Port Name
CLI Commands To set up port mirroring from port 10/3 to port 10/5 in the G250 for all packets sent and received: G250-001(super)# set port mirror source-port 10/3 mirror-port 10/5 sampling always direction both Related commands clear port mirror, show port mirror set port name Use the set port name command to configure a name for a port.
Page 451: Set Port Negotiation
4/5-13 for ports 5 to 13 on module 4 on the G350, or 10/ 5-8 for ETH LAN ports 5 to 8 on the front panel of the G250. Enable port negotiation protocol enable...
Page 452: Set Port Point-To-Point Admin Status
Use the set port point-to-point admin status command to manage the connection type of the port. Note: This command is not supported by the G250. Note: Syntax set port point-to-point admin status module/port admin_status 452 Avaya G250 and Avaya G350 CLI Reference...
Page 453 Alphabetical listing of CLI commands Parameters Parameter Description Possible Values Default Value Number of the module module Number of the port on the port module. You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on module 4.
Page 454: Set Port Powerinline
To enable load detection on ports 3/1, 3/2, and 3/3 of the G350: G350-001(super)# set port powerinline 3/1-3 enable To enable load detection on ports 10/3, 10/4, and 10/5 of the G250: G350-001(super)# set port powerinline 10/3-5 enable Related commands...
Page 455: Set Port Powerinline Priority
To set powering priority to High for ports 3/1, 3/2, and 3/3 on the G350: G350-001(super)# set port powerinline priority 3/1-3 high To set powering priority to High for ports 10/3, 10/4, and 10/5 on the G250: G350-001(super)# set port powerinline priority 10/3-5 high...
Page 456: Set Port Powerinline Type
G350-001(super)# set port powerinline type 6/1-3 telephone G250-001(super)# set port powerinline type 10/5 telephone Related commands set port powerinline, set port powerinline priority, set powerinline trap disable, set powerinline trap enable, show powerinline 456 Avaya G250 and Avaya G350 CLI Reference...
Page 457: Set Port Redundancy
Use the set port redundancy command to globally enable or disable port redundancy on the device. Using this command does not delete existing redundancy entries. Note: This command is not supported by the G250. Note: Syntax set port redundancy {enable|disable}...
Page 458: Set Port Redundancy On|Off
LAG or a LAG interface. Ensure that there is no redundancy scheme already defined on any of the ports. Note: This command is not supported by the G250. Note: Syntax set port redundancy prim_module/prim_port second_module/second_port...
Page 459: Set Port Redundancy-Intervals
Use the set port redundancy-intervals command to configure the two time constants that determine redundancy switchover parameters. Note: This command is not supported by the G250. Note: Syntax set port redundancy-intervals min_time_between_switchovers {switchback_interval | none}...
Page 460: Set Port Spantree
Use the set port spantree command to enable or disable spanning tree for specific ports. Note: This command is not supported by the G250. Note: Syntax set port spantree {enable|disable} [module/port] Parameters Parameter...
Page 461: Set Port Spantree Cost
Use the set port spantree cost command to set the spanning tree cost of a port. This value defines which port will be allowed to forward traffic if two ports with different costs cause a loop. Note: This command is not supported by the G250. Note: Syntax set port spantree cost [module/port] [value]...
Page 462: Set Port Spantree Force-Protocol-Migration
Use the set port spantree force-protocol-migration command to force the port to send a rapid spanning tree hello packet (Bridge Protocol Data Unit). Note: This command is not supported by the G250. Note: Syntax set port spantree force-protocol-migration module/port...
Page 463: Set Port Spantree Priority
This value defines the priority of a port to be blocked in case two ports with the same cost cause a loop. Note: This command is not supported by the G250. Note: Syntax set port spantree priority module/port value...
Page 464: Set Port Speed
10 Mbps Keyword that sets the specified port to a 100MB speed of 100 Mbps Keyword that sets the specified port to a speed of 1 Gbps User level read-write Context general 464 Avaya G250 and Avaya G350 CLI Reference...
Page 465: Set Port Static-Vlan
Alphabetical listing of CLI commands Example To configure port 1 on module 4 to 100 Mbps G350-147# set port speed 4/1 100MB Port 4/1 speed set to 100 Mbps. Related commands set port auto-negotiation-flowcontrol-advertisement, set port disable, set port duplex, set port edge admin state,...
Page 466: Set Port Trap
VLAN 2 is bound to port 3/5 VLAN 2 is bound to port 3/6 To bind ports 3 through 5 on the front panel of the G250 to VLAN 2: G250-001# set port static-vlan 10/3-5 2 VLAN 2 is bound to port 10/3...
Page 467: Set Port Vlan
Alphabetical listing of CLI commands User level read-write Context general Example To enable uplink and downlink traps for port 2 of module 3 on the G350: G350-147# set port trap 3/2 enable Port 3/2 up/down trap enabled. Related commands - SNMP access configuration snmp-server, set snmp community,...
Page 468: Set Port Vlan-Binding-Mode
Use the set port vlan-binding-mode command to define which VLANs will be bound to the specified port. Syntax set port vlan-binding-mode module/port_list value 468 Avaya G250 and Avaya G350 CLI Reference...
Page 469 5, ports 4 through 8 on the G350. To specify ETH LAN ports 3-5 on the front panel of the G250, use the syntax 10/3-5. The type of VLAN binding static - the port supports value only the VLANs that are...
Page 470: Set Powerinline Trap Disable
Use the set powerinline trap enable command to enable the generation of PoE traps and configure the Usage Threshold value. Syntax set port powerinline trap enable module [threshold] 470 Avaya G250 and Avaya G350 CLI Reference...
Page 471: Set Qos Bearer
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value module Number of the module. (Optional) Power consumption usage for 1-99 threshold generating traps, in percent. User level admin Context general Example G350-001(super)# set powerinline trap enable 6 70 Related commands set port powerinline,...
Page 472 To set the BBE differentiated services code point to 43: G350-001(super)# set qos bearer bbedscp 43 Related commands interface FastEthernet, interface serial, queue-limit, set qos control, set qos signal, show ip qos-list, show queue, show voip-parameters, voip-queue-delay 472 Avaya G250 and Avaya G350 CLI Reference...
Page 473: Set Qos Control
Alphabetical listing of CLI commands set qos control Use the set qos control command to define the source for QoS control parameters. The source can be either local where the user configures the values via the CLI, or remote in which case the values are obtained from the Media Gateway Controller.
Page 474: Set Qos Rsvp
| {profile {guaranteed | controlled}} Parameters Parameter Description Possible Default Values Value enable disable refresh The refresh time in seconds 1-99 secs retry noretry guaranteed controlled User level read-write Context general 474 Avaya G250 and Avaya G350 CLI Reference...
Page 475: Set Qos Rtcp
Alphabetical listing of CLI commands Example To set the refresh rate to 15 seconds: G350-001(super)# set qos rsvp refresh 15 To specify no retry upon failure: G350-001(super)# set qos rsvp failure noretry To specify controlled load service: G350-001(super)# set qos rsvp profile controlled To enable RSVP: G350-001(super)# set qos rsvp enable Related commands...
Page 476: Set Qos Signal
Default Value Keyword that specifies to dscp setup DSCP parameters Keyword that specifies to 802p setup 802.1Q parameters Parameter value For dscp: 0-63 For dscp: 34 value For 802p: 0-7 For 802p: 7 476 Avaya G250 and Avaya G350 CLI Reference...
Page 477: Set Radius Authentication
Alphabetical listing of CLI commands User level read-write Context general Example To set up DSCP parameter 43: G350-001(super)# set qos signal dscp 43 Related commands interface FastEthernet, interface serial, queue-limit, set qos bearer, set qos control, show ip qos-list, show queue, show voip-parameters,...
Page 478: Set Radius Authentication Retry-Number
G350-001# set radius authentication retry-number 3 Related commands clear radius authentication server, set radius authentication, set radius authentication retry-time, set radius authentication secret, set radius authentication server, set radius authentication udp-port, show radius authentication 478 Avaya G250 and Avaya G350 CLI Reference...
Page 479: Set Radius Authentication Retry-Time
Alphabetical listing of CLI commands set radius authentication retry-time Use the set radius authentication retry-time command to set the time to wait before resending an access request. Syntax set radius authentication retry-time seconds Parameters Parameter Description Possible Default Values Value The time in seconds to wait before 1–65535 seconds...
Page 480: Set Radius Authentication Server
Possible Default Values Value IP address of RADIUS authentication server ip_addr Keyword that specifies to set the primary primary authentication server (default) Keyword that specifies to set the secondary secondary authentication server 480 Avaya G250 and Avaya G350 CLI Reference...
Page 481: Set Radius Authentication Udp-Port
Alphabetical listing of CLI commands User level read-write Context general Example To set the primary RADIUS authentication server IP address to be 192.40.12.36: G350-147# set radius authentication server 192.40.12.36 primary Related commands clear radius authentication server, set radius authentication, set radius authentication retry-number, set radius authentication retry-time,...
Page 482: Set Reset-Times
To set the primary search timer to 20 minutes: G350-001(super)# set reset-times primary-search 20 Related commands clear mgc list, session, icc-monitoring, mediaserver, set mgc list, show icc-monitoring, show mediaserver, show mgc, show mgc list 482 Avaya G250 and Avaya G350 CLI Reference...
Page 483: Set Security-Association Lifetime
Alphabetical listing of CLI commands set security-association lifetime Use the set security-association lifetime command to set the IKE phase 2 (IPSec) SA (security-association) lifetime. Use the no form of the command to disable the SA lifetime. Syntax [no] set security-association lifetime { seconds seconds | kilobytes {kilobytes | disable} } Parameters Parameter...
Page 484: Set Snmp Community
484 Avaya G250 and Avaya G350 CLI Reference...
Page 485: Set Snmp Retries
Use the set snmp retries command to set the number of times to attempt to communicate with a particular node. Note: This command is not supported by the G250. Note: Syntax set snmp retries number Parameters...
Page 486: Set Snmp Timeout
Use the set snmp timeout command to specify the time to wait for a response before retrying the communication. Note: This command is not supported by the G250. Note: Syntax set snmp timeout time Parameters...
Page 487: Set Snmp Trap
Alphabetical listing of CLI commands Related commands - SNMP trap configuration clear snmp trap, set port trap, set snmp trap, show snmp, snmp trap link-status, snmp-server enable notifications, snmp-server host, snmp-server informs set snmp trap Use the set snmp trap command to define an SNMPv1 trap receiver, or configure its settings.
Page 488 Related commands - SNMP trap configuration clear snmp trap, set port trap, show snmp, snmp trap link-status, snmp-server enable notifications, snmp-server host, snmp-server informs 488 Avaya G250 and Avaya G350 CLI Reference...
Page 489: Set Spantree Default-Path-Cost
Use the set spantree default-path-cost command to set the version of the spanning tree default path cost used by this bridge. Note: This command is not supported by the G250. Note: Syntax set spantree default-path-cost pathcost Parameters...
Page 490: Set Spantree Enable/Disable
As a result, you need to wait 30 seconds before disabling spanning tree if you reset the media gateway, enable spanning tree, or insert a new station. Note: This command is not supported by the G250. Note: Syntax set spantree {enable|disable}...
Page 491: Set Spantree Forward-Delay
Use the set spantree forward-delay command to specify the time used when transferring the state of a port to the forwarding state. Note: This command is not supported by the G250. Note: Syntax set spantree forward-delay seconds...
Page 492: Set Spantree Hello-Time
CLI Commands set spantree hello-time Use the set spantree hello-time command to specify the time interval between the generation of configuration BPDU’s by the root. Note: This command is not supported by the G250. Note: Syntax set spantree hello-time seconds Parameters...
Page 493: Set Spantree Max-Age
Alphabetical listing of CLI commands set spantree max-age Use the set spantree max-age command to specify the time to keep an information message before it is discarded. Note: This command is not supported by the G250. Note: Syntax set spantree max-age seconds Parameters...
Page 494: Set Spantree Priority
CLI Commands set spantree priority Use the set spantree priority command to set the bridge priority for the spanning tree. Note: This command is not supported by the G250. Note: Syntax set spantree priority bridge_priority Parameters Parameter Description Possible Values...
Page 495: Set Spantree Tx-Hold-Count
Use the set spantree tx-hold-count command to set the value in packets used by the spanning tree in order to limit the maximum number of BPDU’s transmitted during a hello-time period. Note: This command is not supported by the G250. Note: Syntax set spantree tx-hold-count rate...
Page 496: Set Spantree Version
CLI Commands set spantree version Use the set spantree version command to set the version of the spanning tree protocol used by the device. Note: This command is not supported by the G250. Note: Syntax set spantree version version Parameters...
Page 497: Set Survivable-Call-Engine
G250-BRI or the G350. Note: If you disable SLS using the set survivable-call-engine command, the Note: ETR function is enabled only after the G250 has registered with an entry from the Media Gateway Controller (MGC) list. Syntax set survivable-call-engine {enable | disable}...
Page 498: Set Sync Interface
To specify that ports 1, 3, 5, 6, 7, and 8 of Media Module 2 are used for normal failover: G350-001(super)# set sync interface primary v2 1,3,5-8 Related commands clear sync interface, set sync source, set sync switching, show sync timing 498 Avaya G250 and Avaya G350 CLI Reference...
Page 499: Set Sync Source
Alphabetical listing of CLI commands set sync source Use the set sync source command to specify which clock source is the active clock source. The identity of the current synchronization source is not stored in persistent storage. Syntax set sync source {primary | secondary | local} Parameters Parameter Description...
Page 500: Set Sync Switching
Disable automatic sync source switching disable User level read-write Context general Example To enable sync source switching: G350-001(super)# set sync switching enable Related commands clear sync interface, set sync interface, set sync source, show sync timing 500 Avaya G250 and Avaya G350 CLI Reference...
Page 501: Set System Contact
Alphabetical listing of CLI commands set system contact Use the set system contact command to set the contact information for this media gateway system. Syntax set system contact [string] Parameters Parameter Description Possible Default Values Value The contact name string should be typed inside string double quotes.
Page 502: Set System Location
Related commands set system contact, set system name set system name Use the set system name command to specify the name of this media gateway system. Syntax set system name [string] 502 Avaya G250 and Avaya G350 CLI Reference...
Page 503: Set Terminal Recovery Password
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The system name string should be typed inside quotes. string The name is cleared if you leave this field blank. User level read-write Context general Examples To set the descriptive name of the system to “G350-HQ”: G350-001(super)# set system name “G350-HQ”...
Page 504: Set Transform-Set
229. Syntax [no] set transform-set name Parameters Parameter Description Possible Values Default Value The name of the transfer set 1-32 characters name User level read-write Context crypto map 504 Avaya G250 and Avaya G350 CLI Reference...
Page 505: Set Trunk
5 to 13 on module 4 of the G350. To specify ETH LAN ports 3-5 on the front panel of the G250, use the syntax 10/3-5. Keyword that specifies to force the port to become a non-tagging port and persuade the neighboring port to become a non-tagging port.
Page 506: Set Trunk-Group
Use the set trunk-group command to configure a trunk group in the SLS data set on the G250. There can be a maximum of four trunk groups for the G250. If you attempt to assign more than the maximum, you must delete a trunk group before you can add a new one.
Page 507: Set Utilization Cpu
Alphabetical listing of CLI commands Context You must be in the survivable-call-engine context before the set trunk-group command will work. Example G250-001(super-survivable-call-engine)# set trunk-group 13 dtmf 9139 loop-start Trunk Group: 13 Dial: dtmf Tac: 9139 Type: loop-start Related commands trunk-group,...
Page 508: Set Vlan
The VLAN name string from 1-32 vlan_name characters User level read-write Context general Example To create VLAN number 3, named “gregory”: G350-147# set vlan 3 name gregory VLAN id 3, vlan-name gregory created. 508 Avaya G250 and Avaya G350 CLI Reference...
Page 509: Set Web Aux-Files-Url
Use the set web aux-files-url command to specify the URL of the Web server containing the online help files and Java plug-in. Note: This command is not supported by the G250. Note: Syntax set web aux-files-url url...
Page 510: Show Application-Memory
Use the show ars-fac command to display the Automatic Route Selection (ARS) Feature Access Code (FAC) within the SLS data set on the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 511: Show Banner Login
Alphabetical listing of CLI commands Syntax show ars-fac User level read-write Context You must be in the survivable-call-engine context before the show ars-fac command will work. Example G250-001(super-survivable-call-engine)# show ars-fac Fac1 Fac2 ---- ----- Output fields Field Description Fac1 First administered Feature Access Code...
Page 512: Show Banner Post-Login
To display the banner that will be shown after a successful login: G350-001(super)# show banner post-login *** Welcome to the G350 Media Gateway CLI Interface *** For questions, please refer to the CLI Reference Guide 512 Avaya G250 and Avaya G350 CLI Reference...
Page 513: Show Boot Bank
Alphabetical listing of CLI commands Related commands banner login, banner post-login, clear screen, hostname, line, show banner login, terminal length, terminal width show boot bank Use the show boot bank command to display the software bank from which the device boots at the next boot process.
Page 514: Show Cam Mac
Use the show cam mac command to display a specific mac entry in the CAM table for a specific VLAN or for all VLANs. Syntax show cam mac mac_address [vlan_number] 514 Avaya G250 and Avaya G350 CLI Reference...
Page 515: Show Cam Vlan
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The MAC entry to display mac_address The VLAN to display vlan_number User level read-only Context general Example To display all entries in VLAN 1 that match the MAC address 00:40:c2:00:66:b0: G350-001(super)# show cam mac 00:40:c2:00:66:b0 1 Related commands clear...
Page 516: Show Capture
Buffer size: 1000 KB Buffer mode is cyclic Maximum number of bytes captured from each frame: 128 Packet filter: Capture List 503 Number of frames in buffer: 200 Size of capture file: 50 KB (5%) 516 Avaya G250 and Avaya G350 CLI Reference...
Page 517: Show Capture-Buffer Hex
Alphabetical listing of CLI commands Related commands capture buffer-mode, capture buffer-size, capture filter-group, capture interface, capture max-frame-size, capture start, capture stop, capture-service, clear capture-buffer, capture-list, name, show capture-buffer hex show capture-buffer hex Use the show capture-buffer hex command to display the contents of the packet sniffing buffer as a hex dump.
Page 518: Show Cna Testplug
CNA testplug 1 is up, test-plug status is running a test Address 149.49.54.114, bind to PMI, ID 00:04:0d:6d:30:48 Scheduler list: 1: 135.64.102.76:50002 (current) 5: 135.64.105.3:50002 Ports: Control 8889, RTP-test 8888, RTP-echo 8887 Test rate limiter: Maximum 60 tests in 10 seconds 518 Avaya G250 and Avaya G350 CLI Reference...
Page 519 Alphabetical listing of CLI commands Last Test: rtp to 149.49.54.114, scheduler: 135.64.102.76:50002 Result: RTP echo started Test Count Failed Cancelled ---------- ------ ------ --------- traceroute ping tcpconnect merge Output fields Name Description test plug 1 is... The status of the test plug service. Possible values are: up.
Page 520 PMI States that the PMI is the test plug’s IP address. The MAC address of the G250/G350, used to identify the test plug. Scheduler list The list of up to five IP addresses of schedulers with which the test plug can attempt to register.
Page 521: Show Composite-Operation
Alphabetical listing of CLI commands Name Description Last Test The current or last test performed by the test plug. Possible values: none. No test has been performed since the test plug was up. traceRoute. The current/last test performed is/was a traceroute test.
Page 522: Show Contact-Closure
Use the show contact-closure command to view the status of a contact closure relay. If no relay is specified, the status of all relays is displayed. Syntax show contact-closure [module/port:relay] 522 Avaya G250 and Avaya G350 CLI Reference...
Page 523 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value Contact closure module to display module Contact closure module port to display port Relay number relay User level read-only Context general Example To display information about all contact closure relays: G350-001(super)# show contact-closure Module port relay admin pulse-duration...
Page 524: Show Controllers
10 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 1 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 3600 Unavail Secs 524 Avaya G250 and Avaya G350 CLI Reference...
Page 525: Show Controllers Remote
Alphabetical listing of CLI commands Related commands - E1/T1 interfaces cablelength long, cablelength short, channel-group, clock source, controller, ds-mode, framing, interface serial, address, linecode (E1), linecode (T1), remote Related commands - Verifying WAN configuration show frame-relay fragment, show frame-relay lmi, show frame-relay pvc, show frame-relay...
Page 526: Show Copy Status
526 Avaya G250 and Avaya G350 CLI Reference...
Page 527: Show Crypto Ipsec Sa
Alphabetical listing of CLI commands show crypto ipsec sa Use the show crypto ipsec sa command to display the IPSec SA database and related runtime, statistical, and configuration information. If no crypto-list, crypto-list rule, or peer IP address are specified, then all SAs are displayed, sorted first by interface and then by crypto-list rule index.
Page 528 Total discards SA Type Transform PFS Secs left KB left Mode ------------ ---------- ------------ --- --------- ------- ---- Inbound ESP 0x1698 esp-des 3501 4607999 Tunnel esp-md5-hmac Outbound ESP 0xfdc7d80c esp-des 3501 4607999 Tunnel 528 Avaya G250 and Avaya G350 CLI Reference...
Page 529 Alphabetical listing of CLI commands esp-md5-hmac -------------------------------------------------------------------- Rule: 20, Crypto map: 1 2. To display the IPSec SA database and related information in detail (in this example, IP Payload Compression (IPPCP) is used): G350-001(super)# show crypto ipsec sa detail Inbound pkts errors (global): Invalid spi Invalid interface Interface: FastEthernet 10/2...
Page 530 * This parameter appears when the detail keyword is specified. This parameter appears when IP Payload Compression (IPPCP) is used. & The SA table is displayed only when active SAs exist for the rule. 530 Avaya G250 and Avaya G350 CLI Reference...
Page 531 Alphabetical listing of CLI commands Name Description Remote identity The remote subnet protected by this SA, as it was configured in the crypto-list rule. The subnet is expressed as <address>/<wildcard>. Path mtu The path MTU kept for this SA, as received from the network by path MTU discovery error messages.
Page 532 * This parameter appears when the detail keyword is specified. This parameter appears when IP Payload Compression (IPPCP) is used. & The SA table is displayed only when active SAs exist for the rule. 532 Avaya G250 and Avaya G350 CLI Reference...
Page 533 Alphabetical listing of CLI commands Name Description Outbound packets Compressed — The total number of packets successfully (Cont) compressed. Incompressible — The total number of incompressible packets when IPPCP is enabled. Comp bypass — The number of incompressible packets due to the packet being too short to compress.
Page 534: Show Crypto Ipsec Transform-Set
[transform-set-name] Parameters Parameter Description Possible Default Values Value The name of the transform set you wish to transform-set-name display. If you do not enter a value, all transform-sets are displayed. 534 Avaya G250 and Avaya G350 CLI Reference...
Page 535 Alphabetical listing of CLI commands User level read-only Context general Example G350-001(super)# show crypto ipsec transform-set Showing 10 rows Name ESP Enc ESP Hash PCP PFS Life Sec Life KB Mode ------------------- ------- -------- --- --- ---------- ---------- ------ sha-hmac No 3600 4608000 Tunnel ts18...
Page 536: Show Crypto Isakmp Peer
New York office vpn.ny.avaya.com vpn.ca.avaya.com AM priod vpn.wip.com IPv4 Address MM on-de Output fields Name Description Auth Pre-shared-key usage: psk — pre-shared-key. ? — no pre-shared-key. The ISAKMP policy. ? — no ISAKMP policy 536 Avaya G250 and Avaya G350 CLI Reference...
Page 537: Show Crypto Isakmp Peer-Group
Alphabetical listing of CLI commands Name Description The IKE mode of operation: MM — Main Mode. AM — Aggressive mode. The keepalive state: K-alv none — no keepAlive on-de — on demand priod — periodic Track Id The ID of the object tracker which is bound to the peer status. Indicates whether or not continuous channel is enabled.
Page 538: Show Crypto Isakmp Policy
Example G350-001(super)# show crypto isakmp policy Id Description Encr Hash Authentication DH group Life sec -- --------------- ------- ------- -------------- -------- ---------- 1 Tel-Aviv-Ike 3des Preshared key 86400 2 Haifa-Ike Preshared key 538 Avaya G250 and Avaya G350 CLI Reference...
Page 539: Show Crypto Isakmp Sa
Alphabetical listing of CLI commands Output fields Name Description The ID of the ISAKMP policy list whose parameters are being listed. Description The description of the ISAKMP policy list. Encr The encryption algorithm used (des, 3des, aes, aes-192, or aes-256). Hash The hashing algorithm used (md5 or sha).
Page 540 The hashing algorithm used (md5 or sha). The authentication type. The Diffie-Hellman group. Time left for SA (set using the lifetime command in crypto isakmp policy context). Whether Dead Peer Detection is enabled. Nat-T Whether NAT-traversal is enabled. 540 Avaya G250 and Avaya G350 CLI Reference...
Page 541: Show Crypto Map
Description Remote Peer / Group Transform-set DSCP C-cnl ---- ------------------- -------------------- -------------------- ---- ----- Tel Aviv VPN 1.0.0.2 Tel-Aviv-Transform copy Yes UK VPN vpn.lnd.uk.avaya.com UK-Transform copy Yes NY VPN group ny-vpn-group NY-Transform copy Yes Haifa VPN 2.1.1.2 Haifa-Transform copy No...
Page 542: Show Csu Loopbacks
Use the show csu loopbacks command to view the state of the server SAT-controlled CSU loopbacks on a media module. Note: This command is not supported by the G250. Note: Syntax show csu loopbacks mmID Parameters...
Page 543: Show Csu Status
Related commands show csu status show csu status Use the show csu status command to view the status of the CSU on a media module. Note: This command is not supported by the G250. Note: Syntax show csu status mmID Parameters...
Page 544 Excessive error rate Loss of frame Alarm indication signal Yellow Pulse density violation (same as BPV) LOOPD Looped Local multiframe alignment Remote multiframe alignment Loss of CRC multiframe Related commands show csu loopbacks 544 Avaya G250 and Avaya G350 CLI Reference...
Page 545: Show Date-Format
Use the show date-format command to display the current date format in effect for the SLS data set in the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 546: Show Dev Log File
Use the show dial-pattern command to list all dial-pattern strings in the SLS data set on the G250 in tabular format. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 547: Show Dot1X
Alphabetical listing of CLI commands Output fields Field Description Dialed String The administered ARS dial string. Length The number of digits in the dial string. Type The type of dial string. Possible types include: emer — emergency call. fnpa — 10-digit NANP call. hnpa —...
Page 548: Show Download License-File Status
User level read-only Context general Example G350-001(super)# show download license-file status Module #10 =========== Module : 10 Source file : /home/llevinsk/EI2/03IS70594996.xml Destination file : license-file Host : 135.64.103.112 Running state : Idle 548 Avaya G250 and Avaya G350 CLI Reference...
Page 549: Show Download Phone-Image-File Status
Alphabetical listing of CLI commands Failure display : (null) Last warning : (null) Bytes Downloaded Related commands copy ftp license-file, copy scp license-file, copy tftp license-file, show license status show download phone-image-file status Use the show download phone-image-file status command to display the status of the download of a phone-image file.
Page 550: Show Download Phone-Script-File Status
550 Avaya G250 and Avaya G350 CLI Reference...
Page 551: Show Download Software Status
Alphabetical listing of CLI commands show download software status Use the show download software status command to display the status of the current Device Manager software download process as the software is being loaded into the module. Syntax show download software status [module_number] Parameters Parameter Description...
Page 552: Show Download Status
Use the show dscp-table command to display a specific entry in the DSCP table. If no DSCP index is specified, the entire DSCP table is displayed. Syntax show dscp-table [index] 552 Avaya G250 and Avaya G350 CLI Reference...
Page 553 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The DSCP entry index User level read-write Context ip qos-list, ip qos-list dscp-table, ip qos-list ip-rule Example To display the entire DSCP table: G350-001(QoS 444)# show dscp-table Trust configuration is trust-cos DSCP Action Precedence...
Page 554: Show Ds-Mode
Current ds-mode: Configured ds-mode: T1 Related commands ds-mode show dynamic-cac Use the show dynamic-cac command to display information about the most recent dynamic CAC event. Syntax show dynamic-cac User level read-only Context general 554 Avaya G250 and Avaya G350 CLI Reference...
Page 555: Show Erase Status
Alphabetical listing of CLI commands Example G350-001(super)# show dynamic-cac Current RBBL : 256 kbps event : 0 Days, 1:21:00 Last event BBL : 256 kbps Related commands dynamic-cac show erase status Use the show erase status command to display the status of the erase startup-config operation.
Page 556: Show Etr
Related commands set etr show extension Use the show extension command to display extension-specific SLS data parameters. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Syntax show extension...
Page 557 Port The module/port location on the G250: v305, v306, or ip (see extension-password for password requirements on IP endpoints). The Class of Restriction. Possible classes include: emergency internal local toll unrestricted Trunk-dest Indicates whether to permit (y) or deny (n) the call.
Page 558: Show Faults
+ No controller found, 01/01-00:00:01.00 Related commands set utilization cpu, show mg list_config, show mgc, show show module, show recovery, show restart-log, show status, show system, show temp, show timeout, show utilization, show voltages, test led 558 Avaya G250 and Avaya G350 CLI Reference...
Page 559: Show Flows
Alphabetical listing of CLI commands show flows Use the show flows command to display information about the real-time status of micro-flows within output queues for the current interface. Note: This command is only applicable in fair-voip-queue mode. Note: Syntax show flows type identifier Parameters Parameter Description...
Page 560: Show Fragment
PVCs, all PVCs associated with an interface, or a specific PVC. Note: When statistics for multiple PVCs are shown, they are sorted first by interface Note: type and number, and then by DLCI. 560 Avaya G250 and Avaya G350 CLI Reference...
Page 561: Show Frame-Relay Lmi
Alphabetical listing of CLI commands Syntax show frame-relay fragment [interface interface_name|dlci_number] Parameters Parameter Description Possible Default Values Value Type and identifier of the interface enclosed interface_name in quotes The PVC identifier 16-1007 dlci_number User level read-only Context general Example To show details on configuration and statistics for fragmentation on all PVCs associated with a Serial interface: G350-001(super)# show frame-relay fragment interface “Serial 5/1”...
Page 562 Invalid Lock Shift Invalid Information ID Invalid Report IE Len Invalid Report Request Invalid Keep IE Len Num Status Enq. Sent Num Status msgs Rcvd Num Update Status Rcvd Num Status Timeouts 562 Avaya G250 and Avaya G350 CLI Reference...
Page 563 Alphabetical listing of CLI commands Output Fields Item Description LMI Statistics Signaling or LMI specification: ANSI, or ITU-T. Invalid Unnumbered info Number of received LMI messages with invalid unnumbered information field. Invalid Prot Disc Number of received LMI messages with invalid protocol discriminator.
Page 564: Show Frame-Relay Map
PVC (DLCI). Note that in this case, all PVCs with the same DLCI are displayed. When statistics for multiple PVCs are shown, they are sorted first by interface type and number, and then by DLCI. Syntax show frame-relay pvc [interface interface_name | dlci_number] 564 Avaya G250 and Avaya G350 CLI Reference...
Page 565 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value Type and identifier of the interface interface_name enclosed in quotes The PVC identifier 16-1007 dlci_number User level read-only Context general Example To show details on configuration and statistics for all PVCs associated with interface “Serial 1.1": G350-001(super)# show frame-relay pvc interface "Serial 1.1"...
Page 566: Show Frame-Relay Pvc Brief
To show a table of all PVCs known to the device: G350-001(super)# show frame-relay pvc brief Related commands clear frame-relay counters, frame-relay class-dlci, interface serial, map-class frame-relay, show frame-relay map, show interfaces 566 Avaya G250 and Avaya G350 CLI Reference...
Page 567: Show Frame-Relay Traffic
Alphabetical listing of CLI commands show frame-relay traffic Use the show frame-relay traffic command to display frame-relay protocol statistics, including ARP requests and replies sent and received over Frame Relay interfaces. Syntax show frame-relay traffic User level read-only Context general Example To display frame-relay statistics: G350-001(super)# show frame-relay traffic...
Page 568: Show Icc-Vlan
VLAN 1 Related commands icc-vlan show image version Use the show image version command to display the software version of the image on both memory banks of the device. Syntax show image version 568 Avaya G250 and Avaya G350 CLI Reference...
Page 569: Show Interfaces
Alphabetical listing of CLI commands User level read-only Context general Example To display the current software versions: G350-001(super)# show image version Bank Version ---- ------- 3.9.7 3.12.10 Module number: 1 Related commands copy ftp EW_archive, copy ftp module, copy ftp SW_imageA, copy ftp SW_imageB,...
Page 570 MTU 1500 bytes. Bandwidth 100000 kbit. Reliability 255/255 txLoad 1/255 rxLoad 1/255 Encapsulation ARPA, ICC-VLAN Link status trap disabled Full-duplex, 100Mb/s ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:30, Last output 00:00:30 570 Avaya G250 and Avaya G350 CLI Reference...
Page 571 Alphabetical listing of CLI commands Last clearing of ’show interface’ counters never. 5 minute input rate 144 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 input drops, 0 output drops, 0 unknown protocols 3425 packets input, 323518 bytes 3425 broadcasts received, 0 giants 0 input errors, 0 CRC 32 packets output, 896 bytes...
Page 572: Show Ip Access-Control-List
{list_number | all | active-list-in | active-list-out | active-list-in-out} [detailed] Parameters Parameter Description Possible Default Values Value The access control list to display list_ number Keyword specifying to display attributes for all access control lists 572 Avaya G250 and Avaya G350 CLI Reference...
Page 573 Alphabetical listing of CLI commands Parameter Description Possible Default Values Value Keyword specifying to display lists for active-list-in the in direction Keyword specifying to display lists for active-list-out the out direction Keyword specifying to display lists for in active-list-in-out and out directions Keyword specifying to display detailed detailed information...
Page 574 List Name: Sync1 Default Action: permit Owner: x9393 List Number: 330 --------------- List Name: Admin13 Default Action: permit Owner: Charlie Related commands access-control-list, access-group, policy-list-copy, qos-group, qos-list, simulate, pre-classification, show ip qos-list 574 Avaya G250 and Avaya G350 CLI Reference...
Page 575: Show Ip Active-Lists
Alphabetical listing of CLI commands show ip active-lists Use the show ip active-lists command to display information about a specific policy list or all lists. Syntax show ip active-lists [list_index | list_type] Parameters Parameter Description Possible Default Values Value The index of the policy list to view 300-499 list_index The type of list: ACL, Crypto, PBR, QoS...
Page 576: Show Ip Active-Pbr-Lists
Use the show ip active-pbr-lists command to display details about a specific PBR list or all PBR lists. Syntax show ip active-pbr-lists {list_number} 576 Avaya G250 and Avaya G350 CLI Reference...
Page 577: Show Ip Arp
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The PBR list to view. 800-899 list_number User level read-only Context general Example To display information about all PBR lists: G350-001(super)# show ip active-pbr-lists Interface Name Index List Name ---------------------------------------- Vlan 1 Voice PBR List...
Page 578 Note: When specifying an interface name that includes spaces, enclose the entire Note: name in quotation marks (for example, “New York”). Related commands arp, timeout, clear arp-cache, max-arp-entries, proxy-arp, show ip reverse-arp 578 Avaya G250 and Avaya G350 CLI Reference...
Page 579: Show Ip Capture-List
Alphabetical listing of CLI commands show ip capture-list Use the show ip capture-list command to display details about capture lists. Syntax show ip capture-list { list-number | all } [detailed] Parameters Parameter Description Possible Values Default Value The capture list to view. 800-899 list_number User level...
Page 580: Show Ip Crypto-List
Values Value The ID of the crypto-list for which to display list-number configuration information. Show all active crypto-lists. active-list Show all crypto-lists. Display detailed configuration information. detail User level read-only Context general 580 Avaya G250 and Avaya G350 CLI Reference...
Page 581 Alphabetical listing of CLI commands Examples To display the configuration of a specific crypto-list: G350-001(super)# show ip crypto-list 901 Index Description Status Owner ----- ------------------------------- --------- ------ VPN_via_leased_Line valid other Local address: 210.210.210.210 Rules: Index Protocol Wildcard Action Crypto map ----- -------- --- ---------------- --------------- ------- --------- 100.1.0.0 0.0.255.255...
Page 582 The ID of the crypto map specifying how to protect traffic. Applicable crypto The table of crypto maps pointed to by this crypto-list, as follows: maps Crypto map ID. Description Crypto map description. 582 Avaya G250 and Avaya G350 CLI Reference...
Page 583: Show Ip Dhcp-Client
Alphabetical listing of CLI commands Name Description Remote IP address or name of remote peer, or name of Peer Group. peer / Group Transform-set The name of the transform-set to which this crypto map points. DSCP The tunnel DSCP configuration, which can be either copy or a decimal number in the range [0-63].
Page 584 Client Identifier: 01:11:22:33:44:55:66 Requested Options: default – router(3) Dns-servers(6) Domain-name(15) Example 2: G350-001(super)# show ip dhcp-client brief Interface Status IP address Lease-Remain (D:H:M:S) --------- ------ ---------- ------------ Fastethernet 10/2 Bound 1.1.1.2 1:2:3:4 584 Avaya G250 and Avaya G350 CLI Reference...
Page 585 Alphabetical listing of CLI commands Output fields Name Description DHCP Whether DHCP Client is Enabled or Disabled. Client Mode Status The status of the DHCP client: Select. Sending DISCOVER packets. Request. Requesting IP address after selecting from all the offered packets. Bound.
Page 586: Show Ip Dhcp-Client Statistics
Note: When the ip address dhcp command is used, the DHCP Client statistics counters Note: for the relevant interface are cleared. The global parameters are not cleared. Syntax show ip dhcp-client statistics 586 Avaya G250 and Avaya G350 CLI Reference...
Page 587 Alphabetical listing of CLI commands User level read-only Context Interface: Fast Ethernet 10/2, general Examples Example 1 shows the usage of the command in the interface context: G350-001(config-if:FastEthernet 10/2)# show ip dhcp-client statistics DHCP client interface statistics: Tx counters: Discover Request Decline Release...
Page 588: Show Ip Dhcp-Pool
Use the show ip dhcp-pool command to display DHCP pool configurations. Syntax show ip dhcp-pool {pool-index|all} [detailed] Parameters Parameter Description Possible Values Default Value The index of a specific pool 1-32 pool-index 588 Avaya G250 and Avaya G350 CLI Reference...
Page 589 End IP Address Range: 1.1.1.20 Lease Time: 8 days 0 hours 0 minutes 0 seconds BootFile: Next-Server: Client-Identifier: Server-Name: DHCP options Option Num Name subnet-maskValue 255.255.255.0 Option Num Name default-router Value 1.1.1.1 Vendor Specific Information Index Name ccp.avaya.com Issue 1.1 June 2005...
Page 590 This is an example too To display the names and statuses of all configured DHCP pools: G350-001(super)# show ip dhcp-pool all Index Name Mode ------ ------------------------- ------------ DHCP pool #5 Inactive DHCP pool #6 Inactive 590 Avaya G250 and Avaya G350 CLI Reference...
Page 591 Name default-router Value 1.1.1.1 Option Num Name SSON Value This is an example Vendor Specific Information Index Name ccp.avaya.com Class-Identifier (null) Value This is an example too Index Name ------- ------------------ DHCP pool #6 Mode: Inactive Start IP Address Range: 2.2.2.2 End IP Address Range: 2.2.2.20...
Page 592 The DHCP options unique to an individual vendor class. These Information options differ according to the different vendors. Related commands bootfile, client-identifier, default-router, dns-server, domain-name, end-ip-addr, lease, name, next-server, option, server-name, start-ip-addr, subnet-mask, value, vendor-specific-option 592 Avaya G250 and Avaya G350 CLI Reference...
Page 593: Show Ip Dhcp-Server Bindings
Alphabetical listing of CLI commands show ip dhcp-server bindings A binding is an assignment of an IP address to a client. Use the show ip dhcp-server bindings command to display bindings. Syntax show ip dhcp-server bindings Parameters User level read only Context general Example...
Page 594: Show Ip Dhcp-Server Statistics
To display DHCP server statistics: G350-001(super)# show ip dhcp-server statistics Counter Value ----------- ------- BOOTP Requests DHCP Discovers DHCP Requests DHCP Declines DHCP Releases DHCP Informs BOOTP Replies DHCP Offers DHCP Acks 594 Avaya G250 and Avaya G350 CLI Reference...
Page 595: Show Ip Distribution Access-Lists
Alphabetical listing of CLI commands Output fields Name Description BOOTP The number of BOOTP Request packets received by the DHCP Requests server DHCP The number of DHCP Discover packets that arrived from DHCP Discovers clients, requesting allocation of a new IP address DHCP The number of DHCP Request packets that arrived from DHCP Requests...
Page 596: Show Ip Domain
DNS servers that were statically configured and those which were gathered using DHCP or PPP protocols, as well as the list of domain suffixes. Syntax show ip domain User level read only Context general 596 Avaya G250 and Avaya G350 CLI Reference...
Page 597 1.1.1.1 Static 2.2.2.2 Static 3.3.3.3 Fast Ethernet 10/2 Index Domain name ----- ---------- emea.avaya.com global.avaya.com avaya.com Output fields Field Description Retries The configured number of retries for a DNS query. Timeout (seconds) The configured timeout for a DNS query. Description The description of the DNS servers list.
Page 598: Show Ip Domain Statistics
Use the show ip domain statistics command to display the DNS Resolver’s statistics counters. Syntax show ip domain statistics User level read only Context general 598 Avaya G250 and Avaya G350 CLI Reference...
Page 599 Alphabetical listing of CLI commands Example G350-001(super)# show ip domain statistics Transaction Type Total Transactions Success Failures --------------- ----------------- ------- -------- Standard query Query Type Total Queries Total Responses Timeouts -------------- ------------ --------------- -------- Standard query Return Code Responses ---------- -------- No Error Format Error...
Page 600: Show Ip Icmp
Use the show ip interface command to display information about an IP interface. Syntax show ip interface [interface_name|ip_interface|ip_address] Parameters Parameter Description Possible Default Values Value The name of the interface whose interface_name information you want to display 600 Avaya G250 and Avaya G350 CLI Reference...
Page 601 Alphabetical listing of CLI commands Parameter Description Possible Default Values Value The name of the IP interface whose string ip_interface information you want to display (1-32 chars) The IP address of the interface whose ip_address information you want to display Note: When specifying an interface name that includes spaces, enclose the entire Note:...
Page 602 TCP/IP header compression is VJ header compression is disabled (default). disabled Related commands show controllers, show frame-relay fragment, show frame-relay lmi, show frame-relay pvc, show frame-relay traffic, show interfaces, show map-class frame-relay 602 Avaya G250 and Avaya G350 CLI Reference...
Page 603: Show Ip Interface Brief
Alphabetical listing of CLI commands show ip interface brief Use the show ip interface brief command to display a summary of the information for a specific interface or for all of the interfaces. Syntax show ip interface brief [interface_name|ip_interface|ip_address] Parameters Parameter Description Possible...
Page 604 Status ------------------------- --------------- ---- ------ --------------------- FastEth 10/2 10.0.0.40 DHCP Related commands description (interface), interface Console, interface FastEthernet, interface Loopback, interface serial, interface tunnel, interface usb, interface vlan, address, admin-state, broadcast-address, load-interval 604 Avaya G250 and Avaya G350 CLI Reference...
Page 605: Show Ip Next-Hop-List
Alphabetical listing of CLI commands show ip next-hop-list Use the show ip next-hop-list command to show the details of the next-hop list. Syntax show ip next-hop-list {next_hop_number | all} Parameters Parameter Description Possible Default Values Value The index number of the entry in 1-20 next_hop_number the next-hop list...
Page 606: Show Ip Ospf
Use the show ip ospf database command to display lists of information related to the OSPF database for a specific router. If no router type is specified, OSPF information is displayed for all routers. Syntax show ip ospf database [asbr-summary|router|network|network-summary|external] 606 Avaya G250 and Avaya G350 CLI Reference...
Page 607 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value Displays information about the autonomous asbr-summary system boundary router summary LSAs Displays information about the router LSAs router Displays information about the network LSAs network Displays information about the network LSAs network-summary summary Displays information about the external LSAs...
Page 608: Show Ip Ospf Interface
AS Router ID 1.1.1.1, COST 1 Transmit Delay 1, State DR, Priority 1 DRId 1.1.1.1, IpAddress 1.1.1.1 BDRId is 0.0.0.0, IpAddress 0.0.0.0 Timer Intervals Configured: Hello 10 Dead 40 Retransmit 5 Neighbor count 0 608 Avaya G250 and Avaya G350 CLI Reference...
Page 609: Show Ip Ospf Neighbor
Alphabetical listing of CLI commands Related commands ip ospf authentication, ip ospf authentication-key, ip ospf cost, ip ospf dead-interval, ip ospf hello-interval, ip ospf message-digest-key, ip ospf network point-to-multipoint, ip ospf priority, ospf router-id, router ospf, show ip ospf, show ip ospf database, show ip ospf neighbor,...
Page 610: Show Ip Pbr-List
PPP L2, USP PPP L2-L3), FastEthernet (L2, L2-L3), VLAN (L2, L2-L3), Loopback (L2, L2-L3), Tunnel (L2, L2-L3) Example G350-001(super)# show ip pbr-list 801 detailed Related commands next-hop-list, pbr-group, pbr-list, show ip active-lists, show ip active-pbr-lists 610 Avaya G250 and Avaya G350 CLI Reference...
Page 611: Show Ip Protocols
Alphabetical listing of CLI commands show ip protocols Use the show ip protocols command to display parameters and statistics of the IP routing protocol process. Syntax show ip protocols [protocol] Parameters Parameter Description Possible Default Values Value The protocol for which to display statistics RIP, OSPF protocol User level...
Page 612: Show Ip Qos-List
Interface: Serial (DS1 PPP L2, DS1 PPP L2-L3, DS1 FR-SUB L2, DS1 FR-SUB L2-L3, USP PPP L2, USP PPP L2-L3), FastEthernet (L2, L2-L3), VLAN (L2, L2-L3), Loopback (L2, L2-L3), Tunnel (L2, L2-L3) 612 Avaya G250 and Avaya G350 CLI Reference...
Page 613: Show Ip Reverse-Arp
Alphabetical listing of CLI commands Example To display information about all QoS lists: G350-001(if:Vlan 1)# show ip qos-list all List Number: 400 --------------- List Name: Default QoS List Default Action: No-Change Owner: other List Trust: trust-cos To display detailed information about all the QoS lists on all the interfaces: G350-001(super)# show ip qos-list all detailed Index Name Owner...
Page 614: Show Ip Route
Related commands arp, timeout, clear arp-cache, max-arp-entries, proxy-arp, show ip arp show ip route Use the show ip route command to display information about the IP routing table. Syntax show ip route [ip_address[ip_mask]] 614 Avaya G250 and Avaya G350 CLI Reference...
Page 615 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The IP address of the routes ip_address The IP mask of the routes ip_mask User level read-only Context general Example To display all routes: G350-001(super)# show ip route Showing 10 rows Network Mask Interface...
Page 616: Show Ip Route Best-Match
TTL Source ----------- ----------- --------- ------------- ---- --- ------- 199.93.0.0 e-135new 135.64.76.1 n/a STAT-HI Related commands clear ip route, default-gateway, route, show ip route, show ip route static, show ip route summary, traceroute 616 Avaya G250 and Avaya G350 CLI Reference...
Page 617: Show Ip Route Static
Alphabetical listing of CLI commands show ip route static Use the show ip route static command to display static routes. Syntax show ip route static [ip_addr [mask]] Parameters Parameter Description Possible Default Values Value The IP address of the routes ip_addr The IP mask of the routes mask...
Page 618: Show Ip Route Summary
Use the show ip rtp header-compression command to display the RTP header compression statistics for a specific interface. If no interface is specified, statistics for all interfaces are displayed. Syntax show ip rtp header-compression [interface_name] 618 Avaya G250 and Avaya G350 CLI Reference...
Page 619 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The name of the interface interface_name User level read-only Context general Example To display RTP compression statistics for all interfaces: G350-001(super)# show ip rtp header-compression IP RTP header compression statistics: Interface Serial 2/1:1.1: Rcvd: 0 Full Headers, 0 Compressed, 0 Errors...
Page 620 620 Avaya G250 and Avaya G350 CLI Reference...
Page 621: Show Ip Rtp Header-Compression Brief
Alphabetical listing of CLI commands show ip rtp header-compression brief Use the show ip rtp header-compression brief command to display a subset of header compression statistics in the form of a table. Syntax show ip rtp header-compression brief [interfaceName] Parameters Parameter Description Possible...
Page 622: Show Ip Ssh
User level admin Context general Example G350-001(super)# show ip ssh Max Sessions: 2 Key type: DSA , 512 bit Listen Port: 22 Ciphers List: 3des-cbc Session Version Encryption Username IP/Port 3des-cbc guest 11.11.11.1/34444 622 Avaya G250 and Avaya G350 CLI Reference...
Page 623: Show Ip Tcp Header-Compression
Alphabetical listing of CLI commands Output fields Name Description Max Sessions The maximum number of concurrent sessions Key type The type of SSH key (always DSA) and the key length Listen Port The SSH server listening port (always 22) Ciphers List List of supported ciphers Session Session ID of each currently active session...
Page 624 Active/Inactive — whether TCP header compression is negotiated and working on this interface. Rx Slots — the number of TCP sessions to decompress. Tx Slots — the number of TCP sessions to compress. 624 Avaya G250 and Avaya G350 CLI Reference...
Page 625: Show Ip Tcp Header-Compression Brief
Alphabetical listing of CLI commands Related commands clear ip rtp header-compression, clear ip tcp header-compression, ip rtp compression-connections, ip rtp header-compression, ip rtp max-period, ip rtp max-time, ip rtp non-tcp-mode, ip rtp port-range, ip tcp compression-connections, ip tcp header-compression, show ip rtp header-compression, show ip rtp header-compression brief show ip tcp header-compression brief...
Page 626: Show Ip Tftp-Server Files
User level Read-write Example G350-001(super)# show ip tftp-server files File Bank Location Size (bytes) ---------- ------------- ---------- -------------- 46xxupgrade.txt phone-scriptA Nv-Ram 4096 46xxsettings.txt phone-scriptB Nv-Ram 16384 4602dbte1_8.bin phone-imageA 1048576 4602dape1_8.bin phone-imageD 2097152 626 Avaya G250 and Avaya G350 CLI Reference...
Page 627: Show Ip Tftp-Server Statistics
The error counters count several types of errors in download and upload operations. Note: Upload operations by TFTP clients, such as IP phones, are not supported. Note: Therefore, any attempts to upload files to the G250 or G350 TFTP server are counted as access violation errors. Syntax show ip tftp-server statistics...
Page 628 628 Avaya G250 and Avaya G350 CLI Reference...
Page 629: Show Ip Traffic
Alphabetical listing of CLI commands show ip traffic Use the show ip traffic command to display IP counters information. Syntax show ip traffic [protocol_type] Parameters Parameter Description Possible Default Values Value The type of IP protocol for which to arp, protocol_type display information bootp-dhcp,...
Page 630 0 link state acks Sent: 0 total ARP statistics: Received: 5394 requests, 2 replies Sent: 36 requests, 16 replies (0 proxy) DHCP statistics: Requests: 0 , Replies: 0 BOOTP statistics: Requests: 0 , Replies: 0 630 Avaya G250 and Avaya G350 CLI Reference...
Page 631: Show Ip Vrrp
Alphabetical listing of CLI commands show ip vrrp Use the show ip vrrp command to display VRRP information for a specific VLAN or for all VLANs. Syntax show ip vrrp [vlan [router-id vr_id]] [detail] Parameters Parameter Description Possible Default Values Value Filter by the specified VLAN 1-4095...
Page 632 # of received Advertisements with Security Violations: 0 Related commands vrrp, ip vrrp address, ip vrrp auth-key, ip vrrp override addr owner, ip vrrp preempt, ip vrrp primary, ip vrrp priority, ip vrrp timer, router vrrp 632 Avaya G250 and Avaya G350 CLI Reference...
Page 633: Show Ip-Codec-Set
Use the show ip-codec-set command to display the IP Codec Set as administered in the SLS data set. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Syntax...
Page 634: Show Ip-Rule
Related commands - Policy-based routing: ip pbr-list destination-ip, dscp (policy, policy-based routing, packet sniffing), next-hop (policy-based routing), show ip next-hop-list Related commands - Policy-based routing: ip pbr-list: ip-rule ip-rule (policy, policy-based routing, packet sniffing), name, owner, show list 634 Avaya G250 and Avaya G350 CLI Reference...
Page 635: Show Isdn Bri Link
Alphabetical listing of CLI commands Related commands - Policy composite-operation, cookie, dscp-table, ip-fragments-in, ip-option-in, ip-rule (policy, policy-based routing, packet sniffing), name, owner, show composite-operation, show dscp-table, show ip-rule, show list, composite-operation, destination-ip, dscp (policy, policy-based routing, packet sniffing), icmp, source-ip, destination-port, established, source-port,...
Page 636: Show Isdn Link Summary
Use the show isdn pri link command to view the status of all PRI links on a media module. Syntax show isdn pri link mmID Parameters Parameter Description Possible Default Values Value The Media Module ID mmID 636 Avaya G250 and Avaya G350 CLI Reference...
Page 637: Show Keepalive-Icmp
Alphabetical listing of CLI commands User level read-only Context general Example To display PRI link information for media module 1: G350-001(super)# show isdn pri link 1 LOCATION TYPE LINK ID DLCI SIDE STATE --------- ------- ---------- ---------- ----- ------------ NO LINK N/A Related commands show isdn bri link,...
Page 638: Show Last-Pim-Update
Use the show last-pim-update command to display when the last Provisioning and Update Manager (PIM) update of the SLS data occurred on the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 639: Show License Status
Alphabetical listing of CLI commands show license status Use the show license status command to display the status of the VPN license. Syntax show license status User level read-only Context general Example G350-001(super)# show license status License was installed. Related commands copy ftp license-file, copy scp...
Page 640: Show Lldp
Use the show lldp command to display the LLDP information received on each port. Syntax: show lldp [module/port] Parameters Parameter Description Possible Default Values Value Number of module 1-10 module Number of port(s) port User level read-only 640 Avaya G250 and Avaya G350 CLI Reference...
Page 641 Port ID: subtype=7 value 048313233343536 Port description: Avaya Inc., G350 Media Gateway, 10/100BaseTx-Pwr System name = System number 1 System description = Avaya Inc., G350 Converged Media Gateway, SW Version 23.8.51 SysCaps :other repeater bridge accessPoint router phone DOCSIS stationOnly...
Page 642: Show Lldp Config
Use the show lldp config command to display the global LLDP configuration. Syntax show lldp config User level read-only Context General Example G250-001(super)# show lldp config 642 Avaya G250 and Avaya G350 CLI Reference...
Page 643: Show Logging File Condition
Alphabetical listing of CLI commands Lldp Configuration ------------------- Application status: enable Tx interval: 30 seconds Tx hold multiplier: 4 Tx delay: 2 seconds Reinit delay: 2 seconds Output fields Name Description Application Whether the LLDP application is enabled or disabled. status Tx interval The interval at which the device transmits LLDP frames.
Page 644: Show Logging File Content
Values Value Minimal severity of messages to be displayed severity Keyword specifying to display messages from all facilities Display messages from this facility only Msgfacility Maximum number of messages to display number 644 Avaya G250 and Avaya G350 CLI Reference...
Page 645: Show Logging Server Condition
Alphabetical listing of CLI commands User level read-only Context general Example To display contents of the message file for all message facilities and severities: G350-001(super)# show logging file content CLI-Notification: root: exit CLI-Notification: root: exit CLI-Notification: root: SECURITY-Warning: Unauthorized Access from IP address = 0.0.0.0, User = super, Protocol = 23 CLI-Notification: root: exit Related commands...
Page 646: Show Logging Session Condition
Use the show logging session condition command to display the filter conditions defined for message logging to the current console session. Syntax show logging session condition User level read-only 646 Avaya G250 and Avaya G350 CLI Reference...
Page 647: Show Logout
Alphabetical listing of CLI commands Context general Example To display filter conditions defined for console messaging: G350-001(super)# show logging session condition Logging console: enabled Logging session severity: warning Facility Severity Override ------------- ----------------------- System Critical Related commands clear logging file, clear logging server, set logging...
Page 648: Show Map-Class Frame-Relay
Use the show max-ip-registrations command to display the maximum IP registration administration in the SLS data on the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Syntax...
Page 649: Show Mediaserver
Alphabetical listing of CLI commands User level read-write Context You must be in the survivable-call-engine context before the show max-ip-registrations command will work. Example G250-001(super-survivable-call-engine)# show max-ip-registrations Maximum IP Registrations is 8 Related commands trunk-group, clear ars-fac, clear survivable-config, clear...
Page 650: Show Mg List_Config
TYPE CODE SUFFIX HW VINTAGE FW VINTAGE ---- ------ ------ ------ ---------- ----------- G350 PC1053 0.0.15(B) -- Not Installed -- -- Not Installed -- -- Not Installed -- -- Not Installed -- 650 Avaya G250 and Avaya G350 CLI Reference...
Page 651: Show Mgc
Alphabetical listing of CLI commands -- Not Installed -- -- Not Installed -- -- Initilalizing -- Related commands set utilization cpu, show faults, show mgc, show show module, show recovery, show restart-log, show status, show system, show temp, show timeout, show utilization, show...
Page 652: Show Mgc List
Use the show mgc list command to display the list of available Media Gateway Controllers and their IP addresses. On the G250, the show mgc list command also shows whether SLS survivability is enabled or disabled. If SLS is enabled, the following message appears at the end of the MGC list:...
Page 653: Show Mm
Alphabetical listing of CLI commands -- Not Available -- The following example shows output for the show mgc list command in the G250: G250-001(super)# show mgc list CONFIGURED MGC HOST --------------------- 135.8.48.220 135.34.54.2 149.49.70.230 -- Not Available -- survivable-call-engine Output fields...
Page 654 Related commands set utilization cpu, show faults, show mg list_config, show mgc, show module, show recovery, show restart-log, show status, show system, show temp, show timeout, show utilization, show voltages, test led 654 Avaya G250 and Avaya G350 CLI Reference...
Page 655: Show Module
Alphabetical listing of CLI commands show module Use the show module command to view information about a Media Module. To view information about all Media Modules, do not specify a Media Module. Syntax show module [mmID] Parameters Parameter Description Possible Default Values Value...
Page 656: Show Next-Hop
Index Next Hop IP/Interface Status ------- --------------------------- ------- 1 149.49.200.3 Down 4 Serial5/1:0 Up Related commands next-hop-interface, next-hop-ip show pmi Use the show pmi command to view the current Primary Management Interface. Syntax show pmi 656 Avaya G250 and Avaya G350 CLI Reference...
Page 657: Show Port
Alphabetical listing of CLI commands User level read-only Context general Example To view information about the current PMI: G350-001(super)# show pmi Active PMI : interface Vlan 1 (172.16.1.139) Configured PMI : interface Vlan 1 (172.16.1.139) Related commands show port Use the show port command to display port status on I/O modules. If no port is specified, information for all ports is displayed.
Page 658: Show Port Auto-Negotiation-Flowcontrol-Advertisement
Use the show port auto-negotiation-flowcontrol-advertisement command to display the flowcontrol advertisement for a Gigabit port used to perform auto-negotiation. If no port is specified, information for all ports is displayed. Syntax set auto-negotiation-flowcontrol-advertisement [module/port] 658 Avaya G250 and Avaya G350 CLI Reference...
Page 659: Show Port Classification
Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The module number module The port number port User level read-only Context general Example To display the flowcontrol advertisement for all ports: G350-001(super)# show port auto-negotiation-flowcontrol-advertisement asym-tx-only 4/49 Port 4/49 pause capabilities was set Related commands set port...
Page 660: Show Port Dot1X
To display information for port 8 of module 4 on the G350: G350-001(super)# show port classification 4/8 Port Port Classification ------ --------------------- regular To display information for port 6 on the front panel of the G250: 250-001(super)# show port classification 10/6 Port Port Classification ------ --------------------- 10/6...
Page 661 For an explanation of the output fields, see the table describing the output of the Note: show port dot1x command in the chapter Accessing the Avaya G250/G350 Media Gateway, in Administration for the Avaya G250 and Avaya G350 Media Gateways, 03-300436. Related commands...
Page 662: Show Port Dot1X Statistics
Port Rx_Invalid Rx_Len_Err Rx_Total Last_Rx_Frm_Ver Last_Rx_Frm_Src_Mac ---- ---------- ---------- -------- --------------- ------------------- 1d-80-00-00-00-00 Output fields Field Description Port Port and module numbers. Tx_Req/Id Number of EAP request/identity frames sent from the port. 662 Avaya G250 and Avaya G350 CLI Reference...
Page 663 Alphabetical listing of CLI commands Field Description Tx_Req Number of EAP request frames (excluding request/identity frames) sent from the port. Tx_Total Total number of EAP frames of any type that have been sent from the port. Rx_Start Number of valid EAP start frames received by the port. Rx_Logff Number of EAP logoff frames received by the port.
Page 664: Show Port Edge State
Use the show port edge state command to display the edge state of the specified port. If no port is specified, information for all ports is displayed. Note: This command is not supported by the G250. Note: Syntax show port edge state [module/[port]]...
Page 665: Show Port Flowcontrol
G350-101(super)# show port flowcontrol 3/4 Port Send-Flowcontrol Receive-Flowcontrol Admin Oper Admin Oper ------ ----- ---- ----- ---- To display flowcontrol information for the front panel of the G250: G250-101(super)# show port flowcontrol 10/4 Port Send-Flowcontrol Receive-Flowcontrol Admin Oper Admin Oper ------ ----- ----...
Page 666: Show Port Lldp Config
OFF — indicates that the local port will discard flow control frames received from the far end. show port lldp config Use the show port lldp config command to display port-level LLDP configuration. Syntax: show port lldp config [module/port] 666 Avaya G250 and Avaya G350 CLI Reference...
Page 667 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value Number of module 1-10 module Number of port(s) port User level read-only Context general Example G350-001(super)# show port lldp config Port Port Port System System System Management Number Status Description Name Description Capability Address PVID...
Page 668: Show Port Lldp Vlan-Name Config
Use the show port lldp vlan-name config command to show the VLANs that are being transmitted on a specific port Syntax: show port lldp vlan-name config [module/port] 668 Avaya G250 and Avaya G350 CLI Reference...
Page 669 Value Number of module 1-10 module Number of port(s) port User level read-only Context general Example G250-001(super)# show port lldp vlan-name config Port Transmitted VLAN-IDs ---- --------------------- 10/3 1, 3 , 50 ,300 10/4 3, 50 … Output fields Name...
Page 670: Show Port Mirror
Number of the port on the module port User level read-only Context general Example To display port mirroring information for all ports: G350-001(super)# show port mirror Related commands clear port mirror, set port mirror 670 Avaya G250 and Avaya G350 CLI Reference...
Page 671: Show Port Point-To-Point Status
Use the show port point-to-point status command to display the point-to-point status of the specified port. If no port is specified, information for all ports is displayed. Note: This command is not supported by the G250. Note: Syntax show port point-to-point status [module/port]...
Page 672: Show Port Redundancy
CLI Commands show port redundancy Use the show port redundancy command to display information about software port redundancy pairs defined on the media gateway. Note: This command is not supported by the G250. Note: Syntax show port redundancy User level...
Page 673: Show Port Trap
Alphabetical listing of CLI commands show port trap Use the show port trap command to display information on SNMP generic link up/down traps sent for a specific port. If no port is specified, information for all ports is displayed. Syntax show port trap [module[/port]] Parameters Parameter...
Page 674: Show Port Vlan-Binding-Mode
2/4 is statically bound port 2/5 is statically bound port 2/6 is statically bound port 2/7 is statically bound port 2/8 is statically bound port 2/9 is statically bound port 2/10 is statically bound 674 Avaya G250 and Avaya G350 CLI Reference...
Page 675: Show Powerinline
Alphabetical listing of CLI commands Related commands clear port static-vlan, clear vlan, icc-vlan, interface vlan, set port static-vlan, set port vlan, port vlan-binding-mode, trunk, vlan, show cam vlan, show port vlan-binding-mode, show trunk, show vlan show powerinline Use the show powerinline command to display the current inline power status of the specified module or port.
Page 676: Show Ppp Authentication
Use the show protocol command to display the status of a specific management protocol, or all protocols. Syntax show protocol [ssh|telnet-client|ssh-client|https|snmp|telnet|http|scp |icmp|recovery-password|ftp-client|tftp|dhcp|dns-client] 676 Avaya G250 and Avaya G350 CLI Reference...
Page 677 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value Keyword indicating to display the status of the ssh protocol Keyword indicating to display the status of telnet-client the telnet-client protocol Keyword indicating to display the status of ssh-client the ssh-client protocol Keyword indicating to display the status of...
Page 678: Show Qos-Rtcp
SSH-CLIENT TELNET-CLIENT SNMPv1 SNMPv3 TELNET HTTP RECOVERY-PASSWORD FTP-CLIENT TFTP DHCP DNS-CLIENT show qos-rtcp Use the show qos-rtcp command to display QoS and RTCP parameters. Syntax show qos-rtcp User level admin Context general 678 Avaya G250 and Avaya G350 CLI Reference...
Page 679 Alphabetical listing of CLI commands Example To display QoS and RTCP information: G350-001(super)# show qos-rtcp PARAMETERS IN EFFECT: -- Downloaded -- QOS PARAMETERS LOCALLY SET DOWNLOADED -------------------- --------------- --------------- Signal 802 Priority: Signal DSCP Bearer 802 Priority: Bearer BBE DSCP Bearer EF DSCP Minimum RTP Port 2048...
Page 680: Show Queue
G250-001(super)# show queue FastEthernet 10/2 G350-001(super)# show queue Serial 3/1:2 Related commands interface FastEthernet, interface serial, queue-limit, set qos bearer, set qos control, set qos signal, show ip qos-list, show voip-parameters, voip-queue-delay 680 Avaya G250 and Avaya G350 CLI Reference...
Page 681: Show Queueing
Alphabetical listing of CLI commands show queueing Use the show queueing command to display the priority queue size, in packets. Syntax show queueing [interface_type if_number] Parameters Parameter Description Possible Values Default Value The type of interface Serial, interface_type Fast-Ethernet The port number of this interface in port: 1, 2 if_number the form:...
Page 682: Show Radius Authentication
Use the show radius authentication command to display all RADIUS authentication configurations. Shared secrets are not displayed. Syntax show radius authentication User level read-only Context general 682 Avaya G250 and Avaya G350 CLI Reference...
Page 683: Show Recovery
Alphabetical listing of CLI commands Example To show RADIUS authentication information: G350-001(super)# show radius authentication Mode: Disable Primary-server: 0.0.0.0 Secondary-server: 0.0.0.0 Retry-number: Retry-time: UDP-port: 1812 Related commands clear radius authentication server, set radius authentication, set radius authentication retry-number, set radius authentication retry-time, set radius authentication secret,...
Page 684: Show Restart-Log
RecoveryEngineUti Related commands set utilization cpu, show faults, show mg list_config, show mgc, show show module, show recovery, show status, show system, show temp, show timeout, show utilization, show voltages, test led 684 Avaya G250 and Avaya G350 CLI Reference...
Page 685: Show Rmon Alarm
Alphabetical listing of CLI commands show rmon alarm Use the show rmon alarm command to display information about existing alarm entries. If no alarm index is specified, information for all alarms is displayed. Syntax show rmon alarm [alarm_index] Parameters Parameter Description Possible Default...
Page 686: Show Rmon Event
Event 32 is active, owned by config Description is resetTrap Event firing causes trap to community public, last fired 0:0:0 Related commands rmon alarm, rmon event, rmon history, show rmon alarm, show rmon history, show rmon statistics 686 Avaya G250 and Avaya G350 CLI Reference...
Page 687: Show Rmon History
Alphabetical listing of CLI commands show rmon history Use the show rmon history command to display information about existing history entries. If no index is specified, information for all history entries is displayed. Syntax show rmon history [history_index] Parameters Parameter Description Possible Default...
Page 688: Show Rmon Statistics
# of dropped packet events (due to a lack of resources): 181377479 # of packets received of length (in octets): 64:1508486650, 65-127:3587014782, 128-255:1989866214, 256-511:378421598, 512-1023:2746475436, 1024-1518:3976219609, Related commands rmon alarm, rmon event, rmon history, show rmon alarm, show rmon event, show rmon history 688 Avaya G250 and Avaya G350 CLI Reference...
Page 689: Show Rtp-Stat Config
For an explanation of the output fields, see the table describing the output of the Note: show rtp-stat config command in the chapter Configuring monitoring applications, in Administration for the Avaya G250 and Avaya G350 Media Gateways, 03-300436. Related commands...
Page 690: Show Rtp-Stat Detailed
Play-Time 186.690sec, Loss 0.0% #1, Avg-Loss 0.1%, RTT 816mS #18, Avg-RTT 463mS, JBuf-under/overruns 0.2%/0.0%, Jbuf-Delay 60mS, Max-Jbuf-Delay 60mS Received-RTP: Packets 6372, Loss 0.0% #0, Avg-Loss 0.0%, RTT 603mS #18, Avg-RTT 267mS, Jitter 690 Avaya G250 and Avaya G350 CLI Reference...
Page 691: Show Rtp-Stat Sessions
For an explanation of the output fields, see the table describing the output of the Note: show rtp-stat detailed command in the chapter Configuring monitoring applications, in Administration for the Avaya G250 and Avaya G350 Media Gateways, 03-300436. Related commands...
Page 692 G729 135.8.76.64 00002 2004-10-15,16:59:06 17:00:15 G729 135.8.76.62 00003 2004-10-15,17:00:41 17:01:40 G723 135.8.76.107 00004 2004-10-18,10:28:33 10:30:29 G729 135.8.76.64 00005 2004-10-18,10:39:03 10:42:15 G723 135.8.76.107 00006 2004-10-18,10:52:26 10:53:15 G729 135.8.76.64 00007 2004-10-18,10:53:42 10:54:29 G723 135.8.76.107 692 Avaya G250 and Avaya G350 CLI Reference...
Page 693 Alphabetical listing of CLI commands 00008 2004-10-18,10:56:31 10:57:34 G729 135.8.76.64 00009 2004-10-18,10:57:39 11:02:38 G729 135.8.76.64 00010 2004-10-18,11:03:13 11:06:07 G723 135.8.76.13 00011 2004-10-18,11:13:56 11:16:46 G723 135.8.76.35 00012 2004-10-18,11:13:58 11:16:46 G723 135.8.76.14 00013 2004-10-18,11:18:47 11:19:32 G723 135.8.76.107 00014 2004-10-18,11:18:50 11:19:59 G723 135.8.76.107 00015 2004-10-18,11:20:23 11:20:53 G723...
Page 694: Show Rtp-Stat Summary
2004-10-20,11:09:07 - G723 135.8.76.107 Note: For an explanation of the output fields, see the explanations in the chapter Note: Configuring monitoring applications, in Administration for the Avaya G250 and Avaya G350 Media Gateways, 03-300436. Related commands rtp-stat clear, rtp-stat event-threshold,...
Page 695: Show Rtp-Stat Thresholds
For an explanation of the output fields, see the table describing the output of the Note: show rtp-stat summary command in the chapter Configuring monitoring applications, in Administration for the Avaya G250 and Avaya G350 Media Gateways, 03-300436. Related commands...
Page 696: Show Rtr Configuration
For an explanation of the output fields, see the table describing the output of the Note: show rtp-stat thresholds command in the chapter Configuring monitoring applications, in Administration for the Avaya G250 and Avaya G350 Media Gateways, 03-300436. Related commands...
Page 697 Alphabetical listing of CLI commands Parameters Parameter Description Possible Values Default Value RTR ID 1-30 rtr-id User level read only Context general Examples G350-001(super)# show rtr configuration RTR# ------- Type: ipIcmpEcho Target Address: 2.2.2.1 Frequency (Milliseconds): 5000 Wait Interval (Milliseconds): 5000 Success Retries: 1 Failure Retries: 5 DSCP: 48...
Page 698: Show Rtr Operational-State
Use the show rtr operational-state command to display the global operational status of the RTR feature, for a specific RTR operation or for all RTR operations. Syntax show rtr operational state [rtr-id] 698 Avaya G250 and Avaya G350 CLI Reference...
Page 699 Alphabetical listing of CLI commands Parameters Parameter Description Possible Values Default Value RTR ID 1-30 rtr-id User level read only Context general Example G350-001(super)# show rtr operational-state Wait Last Change Type Dest Address State S/C F/C Freq Inter S/R F/R d,h:m:s -- ---------- --------------- ----- --- --- ---- ----- --- ---...
Page 700: Show Running-Config
The time that elapsed since the RTR last changed its operational state. Related commands rtr, rtr-schedule, show rtr configuration show running-config Use the show running-config command to display the G250/G350’s current configuration. Syntax show running-config User level read-only Context general...
Page 701: Show Self-Test-Status
Alphabetical listing of CLI commands ds-mode t1 interface Vlan 1 icc-vlan ip address 172.16.1.139 255.255.255.240 interface FastEthernet 10/2 interface Console ip address 10.3.0.1 255.255.255.0 Related commands - Configuration files copy ftp startup-config, copy running-config ftp, copy running-config scp, copy running-config startup-config, copy running-config tftp,...
Page 702: Show Snmp
702 Avaya G250 and Avaya G350 CLI Reference...
Page 703: Show Snmp Engineid
Related commands - Dynamic trap manager snmp-server dynamic-trap-manager show snmp engineID Use the show snmp engineID command to display the SNMP engine ID for the G250/G350. Syntax show snmp engineid User level admin Context general...
Page 704: Show Snmp Group
Related commands - SNMP trap configuration clear snmp trap, set port trap, set snmp trap, show snmp, snmp trap link-status, snmp-server enable notifications, snmp-server host, snmp-server informs Related commands - Dynamic trap manager snmp-server dynamic-trap-manager 704 Avaya G250 and Avaya G350 CLI Reference...
Page 705: Show Snmp Retries
Use the show snmp retries command to display the number of retry attempts to make when attempting to communicate with a node. Note: This command is not supported by the G250. Note: Syntax show snmp retries User level...
Page 706: Show Snmp Timeout
CLI Commands show snmp timeout Use the show snmp timeout command to display the time to wait before resending a communication. Note: This command is not supported by the G250. Note: Syntax show snmp timeout User level read-only Context general...
Page 707: Show Snmp User
Alphabetical listing of CLI commands show snmp user Use the show snmp user command to display configuration information for the specified SNMP user. Syntax show snmp user username [remote EngineID] Parameters Parameter Description Possible Default Values Value The username of the user whose username information you wish to display The engine ID of the remote user...
Page 708: Show Snmp User Summary
Use the show snmp usertogroup command to show the mapping table between SNMPv3 users and groups. Syntax show snmp usertogroup [username] 708 Avaya G250 and Avaya G350 CLI Reference...
Page 709 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value The SNMPv3 username username User level admin Context general Example G350-001(super)# show snmp usertogroup Security Model: v1 Security Name: WriteCommN Group Name: WriteCommG Security Model: v2c Security Name: ReadCommN Group Name: ReadCommG Security Model: v2c Security Name: WriteCommN...
Page 710: Show Snmp View
Related commands - SNMP trap configuration clear snmp trap, set port trap, set snmp trap, show snmp, snmp trap link-status, snmp-server enable notifications, snmp-server host, snmp-server informs Related commands - Dynamic trap manager snmp-server dynamic-trap-manager 710 Avaya G250 and Avaya G350 CLI Reference...
Page 711: Show Spantree
Alphabetical listing of CLI commands show spantree Use the show spantree command to display spanning-tree information. If no port is specified, information for all ports is displayed. Note: This command is not supported by the G250. Note: Syntax show spantree [module[/port]] Parameters...
Page 712 712 Avaya G250 and Avaya G350 CLI Reference...
Page 713: Show Startup-Config
Alphabetical listing of CLI commands show startup-config Use the show startup-config command to show the NVRAM based configuration loaded automatically at startup. Syntax show startup-config User level read-only Context general Example To display the startup configuration: G350-001(super)# show startup-config G350-001(super)# ! version 0.0.13 ds-mode t1 interface Vlan 1...
Page 714: Show Status
To display the status of software downloads for all media modules: G350-001(super)# show download software status TFTP STATUS --------------------------------------------- Module: MGP Source File: mg01_3.com Destination File: BANK B Host: 0.0.0.0 Running State: idle 714 Avaya G250 and Avaya G350 CLI Reference...
Page 715: Show Survivable-Call-Engine
Use the show survivable-call-engine command to display SLS status (enabled or disabled). Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Syntax show survivable-call-engine User level...
Page 716: Show Sync Timing
Related commands clear sync interface, set sync interface, set sync source, set sync switching show system Use the show system command to display information about the device. Syntax show system User level read-only 716 Avaya G250 and Avaya G350 CLI Reference...
Page 717: Show Tcp Syn-Cookies
Alphabetical listing of CLI commands Context general Example To display device information: G350-001(super)# show system System Name System Location System Contact Uptime (d,h:m:s) : 0,7:36:43 MV Time : N/A MAC Address : 00:04:0d:29:c5:11 WAN MAC address : 00:04:0d:29:c5:10 Serial No : 03IS12345678 Model No : G350 Chassis...
Page 718 IN_PROGRESS — connection is in progress ESTABLISHED — connection is established CLOSING — connection is closing Last access The seconds elapsed since the last time a packet was received on the connection from either side 718 Avaya G250 and Avaya G350 CLI Reference...
Page 719 Alphabetical listing of CLI commands Output fields Field Description Connections closed The total number of connections closed in the normal manner, normally using FIN and ACK from both sides Connections closed The total number of connections closed on RST from either on RST side Total discards...
Page 720: Show Temp
Use the show timeout command to display the amount of time in minutes the terminal remains idle before timing out. If the timeout value is 0, there is no timeout limit. The default timeout value is 15 minutes. Syntax show timeout User level read-only 720 Avaya G250 and Avaya G350 CLI Reference...
Page 721: Show Track
Alphabetical listing of CLI commands Context general Example To display the timeout value: G350-001(super)# show timeout CLI timeout is 15 minutes Related commands set utilization cpu, show faults, show mg list_config, show mgc, show show module, show recovery, show restart-log, show status, show...
Page 722 Operational Status Last The time that elapsed since the object tracker last Change changed its operational state Registered Applications A list of the applications registered to receive updates from this object tracker 722 Avaya G250 and Avaya G350 CLI Reference...
Page 723: Show Trunk
Alphabetical listing of CLI commands Related commands rtr, track show trunk Use the show trunk command to display VLAN tagging information for the media gateway. If no port is specified, information for all ports is displayed. Syntax show trunk [module[/port[-port]]] Parameters Parameter Description...
Page 724 Related commands clear port static-vlan, clear vlan, icc-vlan, interface vlan, set port static-vlan, set port vlan, port vlan-binding-mode, trunk, vlan, show cam vlan, show port vlan-binding-mode, show vlan 724 Avaya G250 and Avaya G350 CLI Reference...
Page 725: Show Trunk-Group
Use the show trunk-group command to display trunk group administration in the SLS data on the G250. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350. Syntax...
Page 726: Show Upload Dhcp-Binding-File Status
G350-001(super)# show upload dhcp-binding-file status Module #10 =========== Module : 10 Source file : dhcp-binding Destination file : bbbb Host : 135.64.102.64 Running state : Idle Failure display : (null) Last warning : No-warning 726 Avaya G250 and Avaya G350 CLI Reference...
Page 727: Show Upload Phone-Script-File Status
Alphabetical listing of CLI commands show upload phone-script-file status Use the show upload phone-script-file status command to display the upload phone-script file. Syntax show upload phone-script-file status User level Read only Context general Example If no upload has been performed: G350-001# show upload phone-script-file status Module #10 ===========...
Page 728: Show Upload Status
No source file for upload operation - no upload operation was done. Related commands composite-operation, cookie, copy capture-file ftp, copy capture-file scp, copy capture-file tftp, ip-rule (policy, policy-based routing, packet sniffing), owner, show ip capture-list 728 Avaya G250 and Avaya G350 CLI Reference...
Page 729: Show Username
Alphabetical listing of CLI commands show username Use the show username command to display local user accounts. Syntax show username User level admin Context general Example To display all the defined user accounts: G350-001(super)# show username User account password access-type ----------- -------- ------------...
Page 730: Show Vlan
[vlan_id | name vlan_name] Parameters Parameter Description Possible Default Values Value VLAN number to display 1-3071 vlan_id Keyword indicating to specify the VLAN by name name VLAN name to display vlan_name User level read-only 730 Avaya G250 and Avaya G350 CLI Reference...
Page 731 Alphabetical listing of CLI commands Context general Example To display information for all VLANs: G350-001(super)# show vlan VLAN ID Vlan-name ------- -------------------------------- To display information for VLAN 1: G350-001(super)# show vlan 1 VLAN ID Vlan-name ------- -------------------------------- Switch Ports currently bound to this vlan: In module 10: 3 Switch Ports statically bound to this vlan: None...
Page 732: Show Voip-Parameters
Related commands - VoIP testing busyout voip-dsp, release voip-dsp, test voip-dsp Related commands - QoS interface FastEthernet, interface serial, queue-limit, set qos bearer, set qos control, set qos signal, show ip qos-list, show queue, voip-queue-delay 732 Avaya G250 and Avaya G350 CLI Reference...
Page 733: Show Voltages
Alphabetical listing of CLI commands show voltages Use the show voltages command to view power supply voltages. Syntax show voltages User level read-only Context general Example To display voltage information: G350-001(super)# show voltages Voltage Actual Status Usage ------- ------ ------ ----- -48.0 -48.761 OK...
Page 734: Show Web Aux-Files-Url
Use the show web aux-files-url command to display the URL of the Web server containing online help files and the Java plug-in. Note: This command is not supported by the G250. Note: Syntax show web aux-files-url User level...
Page 735: Shutdown (Interface)
Alphabetical listing of CLI commands Example To enable the test plug: G350-001(cna-testplug 1)# no shutdown Related commands clear counters (CNA test plugs), cna-testplug, cna-testplug-service, control-port, rtp-echo-port, rtp-test-port, scheduler, show cna testplug, test-rate-limit shutdown (interface) Use the shutdown command to set the administrative status of the current interface to down. Use the no form of this command to restore the administrative status for the interface to up.
Page 736: Shutdown (Usb Modem)
Use the no form of this command to enable the USB interface. For security reasons, the USB interface is disabled by default. The USB modem can only be connected after the interface is manually brought up using this command. Note: This command is not supported by the G250. Note: Syntax [no] shutdown...
Page 737: Snmp Trap Link-Status
Alphabetical listing of CLI commands snmp trap link-status Use the snmp trap link-status command to enable Link Up and Link Down traps. Use the no form of this command to restore the default value, interface traps deactivated. Syntax [no] snmp trap link-status User level read-write Context...
Page 738: Snmp-Server Community
Related commands - SNMP trap configuration clear snmp trap, set port trap, set snmp trap, show snmp, snmp trap link-status, snmp-server enable notifications, snmp-server host, snmp-server informs Related commands - Dynamic trap manager snmp-server dynamic-trap-manager 738 Avaya G250 and Avaya G350 CLI Reference...
Page 739: Snmp-Server Dynamic-Trap-Manager
Alphabetical listing of CLI commands snmp-server dynamic-trap-manager Use the snmp-server dynamic-trap-manager command to modify the SNMP settings of the dynamic trap manager. Use the no form of the command to restore the dynamic trap manager to its default settings, and remove all notification type filters. Syntax snmp-server dynamic-trap-manager {traps|informs} {v1|v2c community} [udp-port port] [notification_type_list]...
Page 740: Snmp-Server Enable Notifications
G350. Note: This command overrides the enabling of individual notifications using the Note: snmp-server host command. Syntax [no] snmp-server enable notifications User level admin Context general Example G350-001(super)# snmp-server enable notifications 740 Avaya G250 and Avaya G350 CLI Reference...
Page 741: Snmp-Server Engineid
When you change the SNMP Engine ID, all users other than the default user are Note: invalidated and must be redefined. Note: When the IP address of the G250/G350 changes, the SNMP Engine ID is Note: automatically changed. Syntax snmp-server engineID engineID...
Page 742: Snmp-Server Group
If you specify a particular security group, only that group instance is removed. Syntax snmp-server group groupname {v1|v2c|v3 {auth|noauth|priv}} [read readviewname] [write writeviewname] [notify notifyviewname] no snmp-server group groupname [v1|v2c|v3 {noauth|auth|priv}] 742 Avaya G250 and Avaya G350 CLI Reference...
Page 743 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value A character string of at most 32 characters groupname specifying the group name The group is limited to SNMP v1 functionality The group is limited to SNMP v2c functionality The group has full SNMP v3 functionality (this is the default)
Page 744: Snmp-Server Host
Syntax snmp-server host {host_address | hostname} {traps | informs} {{{v1 | v2c} community} | {v3 [auth | noauth | priv] user}} [udp-port port] [notification-type-list] no snmp-server host host_address [{traps|informs} notification-type-list] 744 Avaya G250 and Avaya G350 CLI Reference...
Page 745 Alphabetical listing of CLI commands Parameters Parameter Description Possible Values Default Value The IP address of the SNMP host_address host. A character string no longer hostname than 32 characters, specifying the hostname of the SNMP host. Send traps to this host traps (messages not requiring acknowledgement).
Page 746 — notifications about link aggregation faults and configuration changes policy — notifications about changes in policy (for L3 devices) link-faults — link-down notifications supply — power supply notifications User level admin Context general 746 Avaya G250 and Avaya G350 CLI Reference...
Page 747: Snmp-Server Informs
Alphabetical listing of CLI commands Example G350-001(super)# snmp-server host 10.1.2.4 informs v3 auth John udp-port 789 config generic Related commands - SNMP access configuration snmp-server, set snmp community, set snmp retries, set snmp timeout, show port trap, show snmp, show snmp engineID, show snmp group,...
Page 748: Snmp-Server Remote-User
If no groups are specified, the user is removed from all groups. Syntax snmp-server remote-user username SNMPEngineID groupname {v1|v2c|v3} [auth {md5|sha} auth-password [priv des56 priv-password]] no snmp-server remote-user username [groupname {v1|v2c|v3}] 748 Avaya G250 and Avaya G350 CLI Reference...
Page 749 Alphabetical listing of CLI commands Parameters Parameter Description Possible Default Values Value A character string no longer than 32 username characters, specifying the username of this user The remote device Engine ID for this user SNMPEngineID A character string no longer than 32 groupname characters, specifying the groupname this user is associated with...
Page 750: Snmp-Server User
A character string no longer than 32 groupname characters, specifying the groupname this user is associated with The user is authorized for SNMP v1 functionality in the specified group 750 Avaya G250 and Avaya G350 CLI Reference...
Page 751 Alphabetical listing of CLI commands Parameter Description Possible Default Values Value The user is authorized for SNMP v2c functionality in the specified group The user is authorized for SNMP v3 functionality in the specified group Use the MAC-MD5-96 authentication protocol Use the HMAC-SHA-96 authentication protocol A character string between 8 and 64...
Page 752: Snmp-Server View
752 Avaya G250 and Avaya G350 CLI Reference...
Page 753: Source-Address
Alphabetical listing of CLI commands Related commands - SNMP trap configuration clear snmp trap, set port trap, set snmp trap, show snmp, snmp trap link-status, snmp-server enable notifications, snmp-server host, snmp-server informs Related commands - Dynamic trap manager snmp-server dynamic-trap-manager source-address Use the source-address command to set the source IP address for RTR operations.
Page 754: Source-Ip
To specify that rule 22 of QoS policy list 460 applies to any packet coming from IP address 135.64.104.102: G350-110(QoS 460/rule 22)# source-ip host 135.64.104.102 Related commands - Policy-based routing destination-ip, dscp (policy, policy-based routing, packet sniffing), icmp, ip-protocol, show ip capture-list, destination-port, source-port, destination-port, udp source-port 754 Avaya G250 and Avaya G350 CLI Reference...
Page 755: Speed (Ppp)
Alphabetical listing of CLI commands Related commands - Policy composite-operation, destination-ip, dscp (policy, policy-based routing, packet sniffing), icmp, show composite-operation, show dscp-table, show ip-rule, destination-port, established, source-port, destination-port, udp source-port Related commands - VPN description (ip rule), destination-ip, crypto-list, ip-rule (VPN), local-address, protect crypto map,...
Page 756: Speed (Interface)
The interface speed 10MB, 100MB speed_rate User level read-write Context Interface: FastEthernet (L2, L2-L3) Example To set the interface speed to 100MB: G350-001(if:FastEthernet 10/2)# speed 100MB Related commands autoneg, duplex, shutdown (interface), traffic-shape rate 756 Avaya G250 and Avaya G350 CLI Reference...
Page 757: Start-Ip-Addr
Alphabetical listing of CLI commands start-ip-addr Use the start-ip-addr command to set the start IP address of a DHCP pool. For manual/ reservation leasing, set the start IP address to be identical to the end IP address. Use the no form of this command to clear the start IP address of the pool.
Page 758: Subnet-Mask
To set the subnet-mask for DHCP pool 5 to 255.255.255.240 by stating the subnet mask prefix: G350-001(DHCP 5)# subnet-mask 28 Related commands bootfile, client-identifier, default-router, dns-server, domain-name, end-ip-addr, lease, name, next-server, option, server-name, show ip dhcp-pool, start-ip-addr, value, vendor-specific-option 758 Avaya G250 and Avaya G350 CLI Reference...
Page 759: Success-Retries
Alphabetical listing of CLI commands success-retries Use the success-retries command to specify how many consecutive answered probes change the status of an RTR operation device from down to up. Use the no form of this command to restore the value to the default. Syntax [no] sucess-retries retries Parameters...
Page 760: Suggest-Key
G350-001(config-peer:149.49.70.1)# suggest-key The suggest key: GNpi1odGNBrB5z4GJLz156jDmRWAGFES G350-001(config-peer:149.49.70.1)# suggest-key 8 alphanumeric The suggest key: iEvKoQ1e Related commands continuous-channel, description (ISAKMP peer), initiate mode aggressive, isakmp-policy, keepalive (VPN), keepalive-track, pre-shared-key, self-identity, show controllers remote 760 Avaya G250 and Avaya G350 CLI Reference...
Page 761: Survivable-Call-Engine
Use the survivable-call-engine command to enter the survivable-call-engine context. In this context, you can administer the SLS data set from the G250 CLI. Note: This command is supported by the Avaya G250-Analog; it is not supported on the Note: G250-BRI or the G350.
Page 762: Tcp Destination-Port
Keyword indicating that a range of range ports is specified The start of a port range for which start_port to apply the rule The end of a port range for which end_port to apply the rule 762 Avaya G250 and Avaya G350 CLI Reference...
Page 763: Tcp Established
Alphabetical listing of CLI commands User level read-write Context ip pbr-list ip-rule, ip capture-list ip-rule, ip qos-list ip-rule, ip access-control-list ip-rule Example To specify that the current rule applies to all packets whose destination port is 300: G350-001(ACL 330/ip rule 22)# tcp destination-port eq 300 Related commands - Policy-based routing destination-ip, dscp (policy, policy-based routing, packet...
Page 764: Tcp Source-Port
Keyword that specifies to apply the rule to a port whose name or number is greater than the specified name or number 764 Avaya G250 and Avaya G350 CLI Reference...
Page 765 Alphabetical listing of CLI commands Parameter Description Possible Default Values Value The name of the port for which to apply the rule port_name The number of the port for which to apply the rule port_number Keyword indicating that a range of ports is range specified The start of a port range for which to apply the rule...
Page 766: Tcp Syn-Cookies
To disable SYN cookies: G350-001(config)# no tcp syn-cookies To disable tcp syn-cookies copy the running configuration to the start-upconfiguration file, and reset the device. Related commands clear tcp syn-cookies counters, show tcp syn-cookies 766 Avaya G250 and Avaya G350 CLI Reference...
Page 767: Tech
Alphabetical listing of CLI commands tech Use the tech command to enter tech mode, where additional tech-related commands are available. Note: This command is reserved for service personnel use only. Note: Syntax tech User level tech Context general Example To enter tech mode: G350-001(super)# tech Password: G350-001(tech)#...
Page 768: Terminal Length
3-200 - Sets the new screen length to the value. User level read-only Context general Example To set the screen to display 24 lines: G350-001(super)# terminal length 24 768 Avaya G250 and Avaya G350 CLI Reference...
Page 769: Terminal Width
Alphabetical listing of CLI commands Related commands banner login, banner post-login, clear screen, hostname, line, show banner login, show banner post-login, terminal width terminal width Use the terminal width command to set the width of the terminal display in characters. Syntax terminal width [characters] Parameters...
Page 770: Test Led
Note: Status changes during the test create SNMP traps. Note: Note: To view the results of the most recent BTR test, refer to show mm on page 653. Note: 770 Avaya G250 and Avaya G350 CLI Reference...
Page 771: Test-Rate-Limit
Use the test-rate-limit command to configure the CNA test rate limiter. The CNA test rate limiter sets the maximum rate of tests that can be run by the CNA test plug embedded in the G250/G350. Use the no form of the command to return the CNA test rate limiter to its default configuration.
Page 772: Threshold Count
The upper threshold for the threshold count 1-50 up_number in the track list command The lower threshold for the threshold count 1-50 down_number in the track list command User level read-write Context track list 772 Avaya G250 and Avaya G350 CLI Reference...
Page 773: Timeout Absolute
Alphabetical listing of CLI commands Examples To specify that for list 5, the state will change from down to up if 4 or more hosts are up: G350-001(config-track list 5)# threshold count up 4 To specify that for list 5, the state will change from up to down if 2 or less hosts are up: G350-001(config-track list 5)# threshold count down 2 Related commands description (object...
Page 774: Timers Basic
Router: rip Example To set the update timer to 30 seconds, and the invalid route timer to 180 seconds: G350-001(router:rip)# timers basic 30 180 Related commands default-metric (RIP), distribution-list, network (RIP), redistribute (RIP) 774 Avaya G250 and Avaya G350 CLI Reference...
Page 775: Timers Spf
Alphabetical listing of CLI commands timers spf Use the timers spf command to configure the delay between SPF calculations when using OSPF. Use the no form of this command to restore the default value. Syntax timers spf spf_holdtime no timers spf Parameters Parameter Description...
Page 776: Traceroute
Press any key to stop traceroute ... 172.16.1.47 10 ms (ttl = 1) Related commands clear ip route, default-gateway, route, show ip route, show ip route best-match, show ip route static, show ip route summary 776 Avaya G250 and Avaya G350 CLI Reference...
Page 777: Track
Alphabetical listing of CLI commands track Use the track command to configure an object tracker. Use the no form of this command to delete the object tracker. You can configure two types of object trackers: An object tracker which tracks the state of a single RTR object. A track list which is composed of multiple previously-defined object trackers.
Page 778 To create Track List 3 and specify that its state should be calculated using a threshold calculation: G350-001(config)# track 3 list threshold count G350-001(config-track list 3)# Related commands description (object tracking), object, rtr, threshold count, show track 778 Avaya G250 and Avaya G350 CLI Reference...
Page 779: Traffic-Shape Rate
Alphabetical listing of CLI commands traffic-shape rate Use the traffic-shape rate command to configure traffic shaping for outbound traffic on the current interface. Syntax traffic-shape rate bit_rate Parameters Parameter Description Possible Default Values Value The bit-rate that traffic is shaped to, in bits 64000-2048000 bit_rate per second...
Page 780: Tree
CLI hierarchy. All commands are listed alphabetically. Syntax tree depth Parameters Parameter Description Possible Default Values Value The level of depth at which to display the list depth of CLI commands User level read-only 780 Avaya G250 and Avaya G350 CLI Reference...
Page 781: Tunnel Checksum
Alphabetical listing of CLI commands Context general Example To display the list of available commands to two levels: G350-001(super)# tree 2 > arp > arp timeout > banner login banner login > line > banner post-login banner post-login > line --type q to quit or space key to continue-- tunnel checksum Use the tunnel checksum command to specify that the router adds a checksum bit to the...
Page 782: Tunnel Destination
The destination IP address for the GRE tunnel ip-address User level read-write Context Interface: Tunnel (L2, L2-L3) Example G350-001(super)# tunnel destination 168.30.10.2 Related commands keepalive (GRE tunnel), tunnel checksum, tunnel key, tunnel path-mtu-discovery, tunnel source, tunnel ttl 782 Avaya G250 and Avaya G350 CLI Reference...
Page 783: Tunnel Dscp
Alphabetical listing of CLI commands tunnel dscp By default, the GRE header copies the DSCP value from the header of the original packet. Use the tunnel dscp command to override the original packet’s DSCP with the specified DSCP value. Use the no form of the command to use the DSCP value of the original packet. Syntax tunnel dscp dscp no tunnel dscp...
Page 784: Tunnel Key
GRE packets User level read-write Context Interface: Tunnel (L2, L2-L3) Example G350-001(super)# tunnel key 7 Related commands keepalive (GRE tunnel), tunnel checksum, tunnel destination, tunnel path-mtu-discovery, tunnel source, tunnel ttl 784 Avaya G250 and Avaya G350 CLI Reference...
Page 785: Tunnel Mode
Alphabetical listing of CLI commands tunnel mode Use the tunnel mode command to specify the encapsulation method of the tunnel. This command is only included for future development, and for conformity with other systems. Currently, the tunnel can only perform GRE encapsulation. Syntax tunnel mode encapsulation no tunnel mode...
Page 786 User level read-write Context Interface: Tunnel (L2, L2-L3) Example G350-001(super)# tunnel path-mtu-discovery age-timer 20 Related commands keepalive (GRE tunnel), tunnel checksum, tunnel destination, tunnel key, tunnel source, tunnel 786 Avaya G250 and Avaya G350 CLI Reference...
Page 787: Tunnel Source
Alphabetical listing of CLI commands tunnel source Use the tunnel source command to specify the IP address of the source interface for the GRE tunnel. The source interface is the interface used to direct all traffic into the tunnel. Note: The CLI does not verify that the specified IP address actually exists.
Page 788: Tunnel Ttl
255 User level read-write Context Interface: Tunnel (L2, L2-L3) Example G350-001(super)# tunnel ttl 16 Related commands keepalive (GRE tunnel), tunnel checksum, tunnel destination, tunnel key, tunnel path-mtu-discovery, tunnel source 788 Avaya G250 and Avaya G350 CLI Reference...
Page 789: Type
Alphabetical listing of CLI commands type Use the type command to specify which type of operation an RTR should employ in its probes, and to specify the address of the remote device to be probed. Note: The type command is available only for newly-created RTRs. You cannot use it Note: for existing RTRs.
Page 790: Udp Destination-Port
The name of the port for which to apply the rule port_name The number of the port for which to apply the port_number rule Keyword indicating that a range of ports is range specified 790 Avaya G250 and Avaya G350 CLI Reference...
Page 791: Udp Source-Port
Alphabetical listing of CLI commands Parameter Description Possible Default Values Value The start of a port range for which to apply the start_port rule The end of a port range for which to apply the end_port rule User level read-write Context ip pbr-list ip-rule, ip qos-list ip-rule, ip capture-list ip-rule, ip access-control-list ip-rule Example...
Page 792 Example To specify that rule 22 applies to all packets whose source port is greater than 95: G350-001(ACL 330/ip rule 22)# udp source-port gt 95 792 Avaya G250 and Avaya G350 CLI Reference...
Page 793: Username
Alphabetical listing of CLI commands Related commands - Policy-based routing destination-ip, dscp (policy, policy-based routing, packet sniffing), icmp, ip-protocol, show ip capture-list, source-ip, destination-port, source-port, udp destination-port Related commands - Policy composite-operation, destination-ip, dscp (policy, policy-based routing, packet sniffing), icmp, show composite-operation, show...
Page 794: Value
Default Value Non-encapsulated value Type of sub-option ascii — ASCII type hex string — hexadecimal ip-address — IP address word — 16 bit number integer — 32 bit number The sub-option value value 794 Avaya G250 and Avaya G350 CLI Reference...
Page 795: Vendor-Specific-Option
Alphabetical listing of CLI commands User level read-write Context dhcp pool vendor specific, dhcp pool option Example To specify IP addresses for World Wide Web servers (DHCP option 72): G350-001(dhcp 5/option 72)# value raw ip-address "135.64.102.1, 135.64.102.2" To enable IP forwarding (DHCP option 19 specifies whether the client should configure its IP layer for packet forwarding): G350-001(dhcp 5/option 19)# value raw hex 01 To set a non-encapsulated value in ASCII format for vendor-specific option 1:...
Page 796: Voip-Queue
Interface: Serial (DS1 PPP L2-L3, DS1 PPP L2, DS1 FR L2, USP FR L2, USP PPP L2, USP PPP L2-L3), FastEthernet (L2, L2-L3) Note: This command is also used in FastEthernet context when traffic shaping is Note: configured. Example To enable VoIP queuing: G350-001(if:Serial 2/1:1)# voip-queue 796 Avaya G250 and Avaya G350 CLI Reference...
Page 797: Voip-Queue-Delay
Alphabetical listing of CLI commands Related commands fair-queue-limit, fair-voip-queue, voip-queue, voip-queue-delay voip-queue-delay Use the voip-queue-delay command to set the maximum query delay for which to estimate. Syntax voip-queue-delay queue_delay_ms Parameters Parameter Description Possible Default Values Value The maximum amount of time that voice 1-1000 queue_delay_ms traffic is allowed to wait in the queue...
Page 798: Wait-Interval
User level read-write Context rtr type Example G350-001(config-rtr icmp 1)# wait-interval 3 seconds Related commands dscp (object tracking), fail-retries, frequency, next-hop (object tracking), rtr, source-address, success-retries, type 798 Avaya G250 and Avaya G350 CLI Reference...
Page 799: Zeroize
Alphabetical listing of CLI commands zeroize Use the zeroize command to clear all secret parameters and initialize the NVRAM to its factory defaults. CAUTION: This command restores factory defaults and disconnects the current session. CAUTION: Syntax zeroize User level admin Context general Example...
Page 800 CLI Commands 800 Avaya G250 and Avaya G350 CLI Reference...
Page 801: Topical Index Of Commands
Topical Index of Commands Topical Index of Commands Numerical 802.1x protocol CAC, see Dynamic CAC ....clear dot1x config Call admission control, see Dynamic CAC .
Page 803 Topical Index of Commands DNS resolver ....... . clear ip domain statistics set etr .
Page 805 Topical Index of Commands LLDP Modem configuration ....... set lldp re-init-delay interface Console .
Page 807 Topical Index of Commands Policy, Port status ip qos-list, (continued) ....show port ....ip-rule .
Page 809 Topical Index of Commands SLS survivability, Status of the device, see Device status survivable-call-engine, (continued) Switch Ethernet ports, see Ethernet port configuration ..show survivable-call-engine Synchronization ....show trunk-group .
Page 811 Topical Index of Commands WAN Ethernet port configuration ....autoneg ... . . interface FastEthernet .
Page 812 Topical Index of Commands 812 Avaya G250 and Avaya G350 CLI Reference...

This manual is also suitable for:

G350

Avaya G250 Reference

About this Book

Chapter 1: User Levels and Contexts

Chapter 2: CLI Commands

Quick Links

Related Manuals for Avaya G250

Summary of Contents for Avaya G250