Depth Stop - Ryobi ECO-2335 User Manual

GB
F D
ADJUSTMENTS
WARNING
Bevel cutting angle is not suitable for the above 2
suggested distances.
To increase the width of cut of your cut-off machine,
■
loosen and remove the fence quick lock and washer.
The use the wrench supplied to loosen and remove
the fence bolt and washers to secure fence to
machine base.
Reposition the curved slot of the fence with the
■
threaded hole (b) at the back of the machine base.
Install a fence quick lock through a flat washer into
■
machine base. Do not tighten fence quick lock
securely.
Align remaining fence bolt hole with the middle
■
threaded hole (a) of the machine base.
Install fence bolt through lock washer and flat washer
■
into machine base.
Check and adjust fence to 0° cutting angle.
■
Securely tighten fence quick lock and fence bolts.
■
This position is good for cutting thin and wide pieces
■
of stock, such as flat or angled stock.
To increase the height of cut of your cut-off machine,
■
follow the above procedure except place the rear
fence bolt in the middle threaded hole (a) and the
front fence bolt in the front threaded hole.
Check and adjust fence to desired cutting angle.
■
Using the wrench provided, securely tighten fence
■
quick lock en fence bolts. Return hex key to its
storage area in base.
This position is good for cutting tall and thick pieces
■
of stock, such as square or tube stock.
LOCK LEVER (Fig. 7-8)
The lock lever engages the vice clamp to be used along
with the fence to provide a vice for securing the workpiece
to be cut. It also allows you to open and close the vice
quickly without repetitive turning of the vice crank handle.
USING THE QUICK LOCK-RELEASE LEVER AND
VICE CLAMP (Fig. 7-8)
To loosen:
Unplug your cut-off machine.
■
WARNING
Failure to unplug cut-off machine could result in
accidental starting causing possible serious
personal injury.
E I P NL S DK N FIN
English
Release tension on the vice clamp by rotating the
■
vice crank handle 1/2 to 1 turn counterclockwise.
Lift up the quick lock-release lever and pull back on
■
vice crank handle to slide open the vice.
To tighten:
Unplug your cut-off machine.
■
WARNING
Failure to unplug cut-off machine could result in
accidental starting causing possible serious
personal injury.
Push the vice crank handle forward to slide the vice
■
clamp against the workpiece.
Rotate the lock lever forward and push down to
■
engage its threads with the vice screw.
Rotate the vice crank handle clockwise to tighten the
■
vice clamp against the workpiece.

DEPTH STOP

The depth stop limits the wheel's downward travel.
It allows the wheel to go below the machine base in order
to maintain full cutting capacities.
The adjustable depth stop is a bolt threaded into the
bracket of the machine at the rear. To adjust the depth
stop, use the wrench to raise or lower the depth stop bolt.
The depth stop has been set already to provide the
maximum cutting capacity for the 355mm (14") abrasive
wheel.
When the diameter of the wheel has been reduced due to
wear, it may be necessary to adjust the depth stop to
provide maximum cutting capacity. When a new abrasive
wheel is installed, it is necessary to check the clearance
of the wheel to the machine base support.
DEPTH STOP ADJUSTMENTS (Fig. 9)
Unplug your cut-off machine.
■
WARNING
Failure to unplug cut-off machine could result in
accidental starting causing possible serious
personal injury.
Loosen the lock nut of the depth stop bolt that is
■
against the machine bracket.
The depth stop is lowered by turning the depth stop
■
bolt clockwise and raised by turning the bolt
counterclockwise.
17
GR H CZ RUS RO PL