4-3 Cleaning Mode
When cleaning the head with hard-type cleaning tape (DY9-1384-000), set up the cleaning mode according to the procedure given
below.
Note :
After head cleaning, be sure to restore the settings to normal.
ST EP
PROCEDURE
1
1) Make setting shown at right.
2) Increases DT by 2.
(Change bit-02 to 1 from 0.)
(Example: 80 → 82)
3) Perform ST ORE. (Press PAUSE key. ↑
2
1) Change over to the normal mode and turn OFF the power supply.
4-4 Commands Particular to Camera
<Outline>
(1) The commands particular to camera are provided for checking the operation.
(2) Make preparation according to the table below and carry out the desired commands particular to camera.
(3) To restore any setting back to the original status, press the PAUSE key (STORE) for each item again in the "ST" mode.
Turning the power OFF/ON resets all the settings.
ST EP
PROCEDURE
CAM SPECIAL COMMAND
WB SET
1) Make setting shown at right.
2) Execute ST ORE. (Press PAUSE.)
WB
1) Make setting shown at right.
LOCK
2) Execute ST ORE. (Press PAUSE.)
WB
1) Make setting shown at right.
T URBO
2) Execute ST ORE. (Press PAUSE.)
WB
1) Make setting shown at right.
OUT DOOR 2) Execute ST ORE. (Press PAUSE.)
WB
1) Make setting shown at right.
INDOOR
2) Execute ST ORE. (Press PAUSE.)
IRIS
1) Make setting shown at right.
OPEN
2) Execute ST ORE. (Press PAUSE.)
IRIS
1) Make setting shown at right.
CLOSE
2) Execute ST ORE. (Press PAUSE.)
AGC
1) Make setting shown at right.
MAX
2) Execute ST ORE. (Press PAUSE.)
AGC
1) Make setting shown at right.
MIN
2) Execute ST ORE. (Press PAUSE.)
COLOR
1) Make setting shown at right.
BAR
2) Execute ST ORE. (Press PAUSE.)
White
1) Make setting shown at right.
100%
2) Execute ST ORE. (Press PAUSE.)
White
1) Make setting shown at right.
50%
2) Execute ST ORE. (Press PAUSE.)
MV750i E, MV730i E, MV700i E, MV700 E, MV690 E
MONIT OR
CS
Function ADDR MODE
0
10
0111
ST
↑
↑
↑
↑
↑
↑
RD
MONIT OR
CS
Function ADDR MODE
2
08
3300
ST
↑
↑
↑
RD
2
08
3301
ST
↑
↑
↑
RD
2
08
3302
ST
↑
↑
↑
RD
2
08
3303
ST
↑
↑
↑
RD
2
08
3304
ST
↑
↑
↑
RD
2
08
3305
ST
↑
↑
↑
RD
2
08
3306
ST
↑
↑
↑
RD
2
08
3309
ST
↑
↑
↑
RD
2
08
330A
ST
↑
↑
↑
RD
2
08
330B
ST
↑
↑
↑
RD
2
08
330C
ST
↑
↑
↑
RD
2
08
330D
ST
↑
↑
↑
RD
9
SERVICE MODE · ADJUSTMENT
Microcomputer operation
DT
--
--
--
Completion of cleaning mode setup
Resetting of cleaning mode
Microcomputer operation
DT
--
--
WB is set.
--
--
WB is locked.
--
--
WB high-speed setting mode
--
--
WB outdoor mode
--
--
WB indoor mode
--
--
T he iris is opened forcibly.
--
--
T he iris is closed forcibly.
--
--
A value of AGC gain is maximized.
--
--
A value of AGC gain is minimized.
--
--
Outputs color bar from DIGIC DV.
--
--
Outputs white 100% from DIGIC DV.
--
--
Outputs white 50% from DIGIC DV.