Cleaning Mode; Commands Particular To Camera - Canon MVX200 E Service Manual

4-3 Cleaning Mode

When cleaning the head with hard-type cleaning tape (DY9-1384-000), set up the cleaning mode according to the procedure given
below.
Note : After head cleaning, be sure to restore the settings to normal.
ST EP PROCEDURE
1 1) Make setting shown at right.
2) Increases DT by 2.
(Change bit-02 to 1 from 0.)
(Example: 80 82)
3) Perform ST ORE. (Press PAUSE key.
2 1) Change over to the normal mode and turn OFF the power supply.

4-4 Commands Particular to Camera

<Outline>
(1) The commands particular to camera are provided for checking the operation.
(2) Make preparation according to the table below and carry out the desired commands particular to camera.
(3) To restore any setting back to the original status, press the PAUSE key (STORE) for each item again in the "ST" mode.
Turning the power OFF/ON resets all the settings.
ST EP PROCEDURE
CAM SPECIAL COMMAND
WB SET 1) Make setting shown at right.
2) Execute ST ORE. (Press PAUSE.)
WB 1) Make setting shown at right.
LOCK 2) Execute ST ORE. (Press PAUSE.)
WB 1) Make setting shown at right.
T URBO 2) Execute ST ORE. (Press PAUSE.)
WB 1) Make setting shown at right.
OUT DOOR 2) Execute ST ORE. (Press PAUSE.)
WB 1) Make setting shown at right.
INDOOR 2) Execute ST ORE. (Press PAUSE.)
IRIS 1) Make setting shown at right.
OPEN 2) Execute ST ORE. (Press PAUSE.)
IRIS 1) Make setting shown at right.
CLOSE 2) Execute ST ORE. (Press PAUSE.)
ND ON 1) Make setting shown at right.
2) Execute ST ORE. (Press PAUSE.)
ND OFF 1) Make setting shown at right.
2) Execute ST ORE. (Press PAUSE.)
AGC 1) Make setting shown at right.
MAX 2) Execute ST ORE. (Press PAUSE.)
AGC 1) Make setting shown at right.
MIN 2) Execute ST ORE. (Press PAUSE.)
COLOR 1) Make setting shown at right.
BAR 2) Execute ST ORE. (Press PAUSE.)
White 1) Make setting shown at right.
100% 2) Execute ST ORE. (Press PAUSE.)
White 1) Make setting shown at right.
50% 2) Execute ST ORE. (Press PAUSE.)
MONIT OR
CS Function ADDR MODE
0 10 0111 ST
RD
MONIT OR
CS Function ADDR MODE
2 08 3300 ST
RD
2 08 3301 ST
RD
2 08 3302 ST
RD
2 08 3303 ST
RD
2 08 3304 ST
RD
2 08 3305 ST
RD
2 08 3306 ST
RD
2 08 3307 ST
RD
2 08 3308 ST
RD
2 08 3309 ST
RD
2 08 330A ST
RD
2 08 330B ST
RD
2 08 330C ST
RD
2 08 330D ST
RD
10
MVX250i E, MVX200i E, MVX200 E
SERVICE MODE · ADJUSTMENT
Microcomputer operation
DT
--
--
-- Completion of cleaning mode setup
Resetting of cleaning mode
Microcomputer operation
DT
--
-- WB is set.
--
-- WB is locked.
--
-- WB high-speed setting mode
--
-- WB outdoor mode
--
-- WB indoor mode
--
-- T he iris is opened forcibly.
--
-- T he iris is closed forcibly.
--
-- ND inserted
--
-- ND in standby state
--
-- A value of AGC gain is maximized.
--
-- A value of AGC gain is minimized.
--
-- Outputs color bar from DIGIC DV.
--
-- Outputs white 100% from DIGIC DV.
--
-- Outputs white 50% from DIGIC DV.