Advertisement
Quick Links
25-Apr-2016
Installing a CPU in Airtop-C0
Required tools
1. LGA1150 compatible CPU (Haswell or Broadwell)
2. Phillips screwdriver
3. Allen 2.5mm screwdriver
4. 5.5mm nut driver
5. 4.5mm nut driver
6. Soft cloth
7. Thermal paste (recommended Arctic Silver 5)
Preparation
1. Disconnect Airtop from power
2. Disconnect all cables
3. Open Airtop clamshell by pressing the top-bar
Dissassembly
1. Take out disk cartridge
Hayetsira St. 17, Yokneam, Israel
Tel:
+972-48-290-100
Fax:
+972-48-325-251
www.compulab.co.il
Advertisement
Related Manuals for CompuLab Airtop-C0
Summary of Contents for CompuLab Airtop-C0
- Page 1 Hayetsira St. 17, Yokneam, Israel Tel: +972-48-290-100 Fax: +972-48-325-251 www.compulab.co.il 25-Apr-2016 Installing a CPU in Airtop-C0 Required tools 1. LGA1150 compatible CPU (Haswell or Broadwell) 2. Phillips screwdriver 3. Allen 2.5mm screwdriver 4. 5.5mm nut driver 5. 4.5mm nut driver 6.
- Page 2 Hayetsira St. 17, Yokneam, Israel Tel: +972-48-290-100 Fax: +972-48-325-251 www.compulab.co.il 2. Remove WiFi module 3. Remove FACE Module 4. Disconnect I3M flat cable 5. Disconnect PCIe flex cable...
- Page 3 Hayetsira St. 17, Yokneam, Israel Tel: +972-48-290-100 Fax: +972-48-325-251 www.compulab.co.il 6. Unscrew motherboard (6 screws) 7. Unscrew CPU counter plate (4 nuts). Pay extra attention to washer stacking 8. Remove the two washers from each stand-off (8 overall)
- Page 4 Hayetsira St. 17, Yokneam, Israel Tel: +972-48-290-100 Fax: +972-48-325-251 www.compulab.co.il 9. Pull out motherboard. Slide it to the right to take out from within Airtop...
-
Page 5: Installing Cpu
Hayetsira St. 17, Yokneam, Israel Tel: +972-48-290-100 Fax: +972-48-325-251 www.compulab.co.il Installing CPU 1. Open ILM 2. Install CPU and close ILM... - Page 6 Hayetsira St. 17, Yokneam, Israel Tel: +972-48-290-100 Fax: +972-48-325-251 www.compulab.co.il 3. Clean thouroughly surface of IHS (CPU metal cover) and surface of heatplate 4. Apply thermal grease on CPU. Compulab recommends Arctic Silver 5...
- Page 7 Hayetsira St. 17, Yokneam, Israel Tel: +972-48-290-100 Fax: +972-48-325-251 www.compulab.co.il Reassembly 1. Note that each standoff should have a washer. 2. Place motherboard.
- Page 8 Tel: +972-48-290-100 Fax: +972-48-325-251 www.compulab.co.il 3. Place washers on standoffs. 4. Place counter plate and while pressing the center of the counter plate for alignment, screw the 4 nuts and washers on counter plate without tightening 5. Screw two motherboard screws without tightening...
- Page 9 +972-48-290-100 Fax: +972-48-325-251 www.compulab.co.il 6. Carefully tighten nuts of counter-plate in opposite diagonals, slight tightening (quarter a rotation) every time. Final tightening moment should be approx. 0.3Nm (or about the force you would manually use with a screwdriver without a lever) 7.