1. Manuals
  2. Brands
  3. Ultra Start Manuals
  4. Remote Starter
  5. 12 SERIES
  6. Install manual

Ultra Start 12 SERIES Install Manual

Hide thumbs Also See for 12 SERIES:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
INSTALL GUIDE
Covers All 12xx and 13xx Series Remote Starters
REMOTE STARTERS
CAR ALARMS
ü
WWW.ULTRASTARTERS.COM
Technical Support 866-698-5872 ext 0
Support@ultrastarters.com
-The system must be placed into Service Mode before any service work is started on
the vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done.
The manufacturer accepts no liability or responsibility for accidental starting of the
vehicle.
- CARBON MONOXIDE - Never Start in an Enclosed Building (Garage, Carport etc...)

Advertisement

Table of Contents
loading

Related Manuals for Ultra Start 12 SERIES

Summary of Contents for Ultra Start 12 SERIES

  • Page 1 INSTALL GUIDE Covers All 12xx and 13xx Series Remote Starters REMOTE STARTERS CAR ALARMS ü WWW.ULTRASTARTERS.COM Technical Support 866-698-5872 ext 0 Support@ultrastarters.com -The system must be placed into Service Mode before any service work is started on the vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no liability or responsibility for accidental starting of the vehicle.

  • Page 2: Table Of Contents

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 2 Table of Contents Table of Contents Page 2 Pre-Installation Page 3 Components Feature List Pre-Installation Installation Procedures Page 4 Wiring Diagrams Page 5-7 Wire Description Page 8-9 6 Pin Connector Auxiliary Connectors Optional Connectors Jumper Positions Quick Start Installation Page 10...

  • Page 3: Components

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 3 Components - Control module - 4 Button remote transmitter’s - Antenna with built in - 6 pin main harness Program Button - 11 pin harness** - 14 pin harness* - 4 pin harness** - 3 pin keyless entry harness - 2 pin Harness (1350 and LT Models) - Hood pin safety switch...

  • Page 4: Installation Procedures

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 4 Recommended Installation Procedures Proper Connections - Remote Starters can handle loads of up to 30 amps for extended periods of time. It is critical to insure that all high current connections are properly soldered and insulated with quality electrical tape. Failing to insure proper connections will result in warranty being VOID and can result in damage to the vehicle and remote starter module.
  • Page 5 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 5 Wiring Diagram - 11 pin + 4 pin Connectors 30amp Output Starter Output YELLOW Heater/Acc Output 30amp Output GREEN 30amp Input Power Input 30amp Input Power Input Selectable Output 30amp Output WHITE 30amp Output Ignition Output BLUE (-)250ma Output...
  • Page 6 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 6 Wiring Diagram 14 pin connector Starter Output YELLOW 30amp Output GREEN 30amp Output Heater/Acc Output 30amp Input Power Input 30amp Input Power Input Selectable Output 30amp Output WHITE 30amp Output Ignition Output BLUE (-)250ma Output Factory Re-arm Output YELLOW...
  • Page 7 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 7 Wiring Diagram auxiliary connectors * The centre pin of the keyless entry harness is not to be used for anything besides plug-in devices such as the VP-1, DL-3, DL-7 and Data Bus Modules. Overloading this output will damage the remote starter.

  • Page 8: Pin Connector

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 8 6 Pin Power Connector 6-pinDescription Test For Wire 1-Yellow 30amp Starter Output - This wire will test 0volts in off, accessory and in the ignition position.12volts during start only. 2-Green 30amp Heat/Acc Output - This wire will test 0volts in the off position 12- 14volts in the accessory and run positions and 0 volts during start 3-Red 30amp Power Input - 12volts at ignition harness or from battery.

  • Page 9: Auxiliary Connectors

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 9 Auxiliary Connectors continued from previous page 11-Black Ground - System Chassis Ground Input. 12-Blue Glow Plug - Diesel Glow plug input, detects both 12volt and negative glow plug signals. Programmable input. See Menu 3. 13-Blue/White Tach - A/C Tach Signal Input.

  • Page 10: Plug-In The Module

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 10 Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow 30amp Starter Output - 12volts during start position only. Green 30amp Heater Output - 12volts in the accessory position off during start and 12volts during run.

  • Page 11: Clutch Bypass

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 11 Manual Transmission “M” Models Never install an automatic transmission remote starter into a manual transmission vehicle!!! Doing so may result in serious injury or death. Do not install remote starters in convertible vehicles! The following wires must be connected In addition to the basic remote starter installation.
  • Page 12 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 12 Auto Tach Learn 1) Turn the ignition key to the “ON” position. (The park lights will turn on*). 2) Start the vehicle with the key, The LEDs on the antenna will turn on if a proper tach signal is detected**, then after 30-35 seconds the park lights will flash and the horn (Optional) will honk twice to confirm Tach Learn.

  • Page 13: Important Tach Notes

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 13 Important Tach Notes Tach Learning the remote starter is one of the most important steps in the installation process. Do not tach learn vehicle while the engine is in high idle. To ensure the best possible tach setting, ensure that the vehicle is at low idle/ normal operating RPM.

  • Page 14: Entering Program Mode

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 14 Entering Program Mode 1) With the ignition in the OFF position, turn the ignition key from “Off” to “On” 3 times, ON-OFF-ON-OFF-ON within three seconds. (Leave the key in the ON position) 2) Press and release the Program Button located on the antenna. The park lights will flash and the horn (optional) will honk to confirm entering program mode.

  • Page 15: Quick View Programming

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 15 Quick View Programming * See the following pages for more detailed programming instructions. Menu 1 - Press Lock 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Horn Honk Type 1 Type 2 All Honks...
  • Page 16 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 16 Menu 1- User Settings Press and Ignition 3x Press and Press and Press and Release the On/Off Release the Release the Hold the Ignition ON-OFF-ON-OFF-ON Program Switch On/Off On Program lock button for Program Switch Press &...
  • Page 17 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 17 Menu 2- Additional Settings Press and Ignition ON-OFF-ON-OFF-ON Press and Release the Hold the Press & Release Program Button Ignition 3x Press and Press and Program Switch Program Switch On/Off Release the Release the Press Unlock 1x =Setting 1 1x = Option 1...
  • Page 18 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 18 Menu 3- Starter Settings Ignition ON-OFF-ON-OFF-ON Press and Ignition 3x Press and Press and Press and Press & Release Program Button Release the On/Off Release the Release the Hold the Program Switch On/Off On Program Start button Program Switch...
  • Page 19 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 19 Menu 3- Starter Settings - Continued From Previous Page Setting 4 Run Time 1) 4 Minutes 1 Flash/Honk Runs for approximately 4 minutes when activated. 2) 45 Minutes 2 Flashes/Honks Runs for approximately 45 minutes when activated. *3) 15 Minutes 3 Flashes/Honks Runs for approximately 15 minutes when activated.
  • Page 20 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 20 Menu 4- Tach Settings Press and Ignition 3x Press and Press and Press and Release the On/Off Release the Release the Hold the Program Switch On/Off On Program # button Program Switch 1x =Setting 1 Auto Tach Learn.

  • Page 21: Transmitter Programming

    Lock Button Lock Button On/Off On Program Button Dual Car, Control 2 Ultra Start Single Car Operation, Program up to 4 remote’s vehicles with the same remote Battery Replacement The transmitter battery should be changed at least once every year to maintain proper operating range.
  • Page 22 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 22 Negative Type Door Locks 250ma Vehicle Lock To Control Lock/Unlock Relay or Switch Actuators lock Green Blue Negative Door Locks (More Than 250ma) Fused +12V Vehicle Ground Lock/Unlock Lock lock Switch Green Blue To Control Relay or Actuator Positive Type Door Locks...
  • Page 23 INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 23 5 Wire / Reverse Polarity Type Door Locks Fused +12V Green Blue Vehicle Lock To Actuator Lock/Unlock Switch lock Aftermarket Doorlock Actuators Ground Vacuum Type Door Locks DIAGNOSTICS Ground Fused +12V Green Blue Lock To Vacuum Pump...

  • Page 24: Diagnostics

    INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 24 DIAGNOSTICS If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example when the start button is pressed the park lights flash 3 times slowly. Looking at the chart below this would indicate that the system is in Service Mode, simply follow the instructions listed in the owners manual on exiting Service Mode and the remote starter will begin to function as normal.

This manual is also suitable for:

13 series

Table of Contents