Table of Contents
Advertisement
!
ASBESTOS FIBER WARNING
The following procedures for servicing brakes are recommended
to reduce exposure to asbestos fiber dust, a cancer and lung
disease hazard. Material Safety Data Sheets are available from
Rockwell.
Hazard Summary
Because some brake linings contain asbestos, workers who service brakes must understand the
potential hazards of asbestos and precautions for reducing risks. Exposure to airborne asbestos
dust can cause serious and possibly fatal diseases, including asbestosis (a chronic lung disease)
and cancer, principally lung cancer and mesothelioma (a cancer
of the lining of the chest or abdominal cavities). Some studies show that the risk of lung cancer
among persons who smoke and who are exposed to asbestos is much greater than the
risk for non-smokers. Symptoms of these diseases may not become apparent for 15, 20 or more
years after the first exposure to asbestos.
Accordingly, workers must use caution to avoid creating and breathing dust when servicing
brakes. Specific recommended work practices for reducing exposure to asbestos dust follow.
Consult your employer for more details.
Recommended Work Practices
1. Separate Work Areas. Whenever feasible, service brakes in a separate area away from
other operations to reduce risks to unprotected persons. OSHA has set a maximum allowable
level of exposure for asbestos of 0.1 f/cc as an 8-hour time-weighted average and 1.0 f/cc
averaged over a 30-minute period. Scientists disagree, however, to what extent adherence to the
maximum allowable exposure levels will eliminate the risk of disease that can result from inhaling
asbestos dust. OSHA requires that the following sign be posted at the entrance to areas where
exposures exceed either of the maximum allowable levels:
DANGER: ASBESTOS
CANCER AND LUNG DISEASE HAZARD
AUTHORIZED PERSONNEL ONLY
RESPIRATORS AND PROTECTIVE CLOTHING
ARE REQUIRED IN THIS AREA
2. Respiratory Protection. Wear a respirator equipped with a high-efficiency (HEPA) filter
approved by NIOSH or MSHA for use with asbestos at all times when servicing brakes,
beginning with the removal of the wheels.
3. Procedures for Servicing Brakes.
a) Enclose the brake assembly within a negative pressure enclosure. The enclosure should be
equipped with a HEPA vacuum and worker arm sleeves. With the enclosure in place, use
the HEPA vacuum to loosen and vacuum residue from the brake parts.
b) As an alternative procedure, use a catch basin with water
and a biodegradable, non-phosphate, water-based detergent to wash the brake drum or
rotor and other brake parts. The solution should be applied with low pressure to prevent dust
from becoming airborne. Allow the solution to flow between the brake drum and the brake
support or the brake rotor and caliper. The wheel hub and brake assembly components
should be thoroughly wetted to suppress dust before the brake shoes or brake pads are
removed. Wipe the brake parts clean with a cloth.
c) If an enclosed vacuum system or brake washing equipment is not available, employers may
adopt their own written procedures for servicing brakes, provided that the exposure levels
associated with the employer's procedures do not exceed the levels associated with the
enclosed vacuum system or brake washing equipment. Consult OSHA regulations for more
details.
d) Wear a respirator equipped with a HEPA filter approved
by NIOSH or MSHA for use with asbestos when grinding or machining brake linings. In
addition, do such work in an area with a local exhaust ventilation system equipped with a
HEPA filter.
e) NEVER use compressed air by itself, dry brushing, or a vacuum not equipped with a HEPA
filter when cleaning brake parts or assemblies. NEVER use carcinogenic solvents,
flammable solvents, or solvents that can damage brake components as wetting agents.
4. Cleaning Work Areas. Clean work areas with a vacuum equipped with a HEPA filter or by wet
wiping. NEVER use compressed air or dry sweeping to clean work areas. When you empty
vacuum cleaners and handle used rags, wear a respirator equipped with a HEPA filter approved
by NIOSH or MSHA for use with asbestos. When you replace a HEPA filter, wet the filter with a
fine mist of water and dispose of the used filter with care.
5. Worker Clean-Up. After servicing brakes, wash your hands before you eat, drink or smoke.
Shower after work. Do not wear work clothes home. Use a vacuum equipped with a HEPA filter
to vacuum work clothes after they are worn. Launder them separately. Do not shake or use
compressed air to remove dust from work clothes.
6. Waste Disposal. Dispose of discarded linings, used rags, cloths and HEPA filters with care,
such as in sealed plastic bags. Consult applicable EPA, state and local regulations on waste
disposal.
Regulatory Guidance
References to OSHA, NIOSH, MSHA, and EPA, which are regulatory agencies in the United
States, are made to provide further guidance to employers and workers employed within the
United States. Employers and workers employed outside of the United States should consult the
regulations that apply to them for further guidance.
Page 2
Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • parts@eprogear.com
NON-ASBESTOS
!
FIBER WARNING
The following procedures for servicing brakes are recommended
to reduce exposure to non-asbestos fiber dust, a potential cancer
and lung disease hazard. Material Safety Data Sheets are available
from Rockwell.
Hazard Summary
Most recently manufactured brake linings do not contain asbestos fibers. These brake linings
may contain one or more of a variety of ingredients, including glass fibers, mineral wool,
aramid fibers, ceramic fibers and silica that can present health risks if inhaled. Scientists
disagree on the extent of the risks from exposure to these substances. Nonetheless,
exposure to silica dust can cause silicosis, a non-cancerous lung disease. Silicosis gradually
reduces lung capacity and efficiency and can result in serious breathing difficulty. Some
medical experts believe other types of non-asbestos fibers, when inhaled, can cause similar
diseases of the lung. In addition, silica dust and ceramic fiber dust are known to the State of
California to cause lung cancer. U.S. and international agencies have also determined that
dust from mineral wool, ceramic fibers and silica are potential causes of cancer.
Accordingly, workers must use caution to avoid creating and breathing dust when servicing
brakes. Specific recommended work practices for reducing exposure to non-asbestos dust
follow. Consult your employer for more details.
Recommended Work Practices
1. Separate Work Areas. Whenever feasible, service brakes in a separate area away from
other operations to reduce risks to unprotected persons.
2. Respiratory Protection. OSHA has set a maximum allowable level of exposure for silica of
0.1 mg/m
3
as an
8-hour time-weighted average. Some manufacturers of non-asbestos brake linings
recommend that exposures to other ingredients found in non-asbestos brake linings be kept
below 1.0 f/cc as an 8-hour time-weighted average. Scientists disagree, however, to what
extent adherence to these maximum allowable exposure levels will eliminate the risk of
disease that can result from inhaling non-asbestos dust.
Therefore, wear respiratory protection at all times during brake servicing, beginning with the
removal of the wheels. Wear a respirator equipped with a high-efficiency (HEPA) filter
approved by NIOSH or MSHA, if the exposures levels may exceed OSHA or manufacturer's
recommended maximum levels. Even when exposures are expected to be within the
maximum allowable levels, wearing such a respirator at all times during brake servicing will
help minimize exposure.
3. Procedures for Servicing Brakes.
a) Enclose the brake assembly within a negative pressure enclosure. The enclosure should
be equipped with a HEPA vacuum and worker arm sleeves. With the enclosure in place,
use the HEPA vacuum to loosen and vacuum residue from the brake parts.
b) As an alternative procedure, use a catch basin with water and a biodegradable, non-
phosphate, water-based detergent to wash the brake drum or rotor and other brake parts.
The solution should be applied with low pressure to prevent dust from becoming airborne.
Allow the solution to flow between the brake drum and the brake support or the brake rotor
and caliper. The wheel hub and brake assembly components should be thoroughly wetted
to suppress dust before the brake shoes or brake pads are removed. Wipe the brake parts
clean with a cloth.
c) If an enclosed vacuum system or brake washing equipment is not available, carefully clean
the brake parts in the open air. Wet the parts with a solution applied with a pump-spray
bottle that creates a fine mist. Use a solution containing water, and, if available, a
biodegradable, non-phosphate, water-based detergent. The wheel hub and brake
assembly components should be thoroughly wetted to suppress dust before the brake
shoes or brake pads are removed. Wipe the brake parts clean with a cloth.
d) Wear a respirator equipped with a HEPA filter approved by NIOSH of MSHA when
grinding or machining brake linings. In addition, do such work in an area with a local
exhaust ventilation system equipped with a HEPA filter.
e) NEVER use compressed air by itself, dry brushing, or a vacuum not equipped with a
HEPA filter when cleaning brake parts or assemblies. NEVER use carcinogenic solvents,
flammable solvents, or solvents that can damage brake components as wetting agents.
4. Cleaning Work Areas. Clean work areas with a vacuum equipped with a HEPA filter or by
wet wiping. NEVER use compressed air or dry sweeping to clean work areas. When you
empty vacuum cleaners and handle used rags, wear a respirator equipped with a HEPA filter
approved by NIOSH or MSHA, if the exposure levels may exceed OSHA or manufacturers'
recommended maximum levels. When you replace a HEPA filter, wet the filter with a fine mist
of water and dispose of the used filter with care.
5. Worker Clean-Up. After servicing brakes, wash your hands before you eat, drink or
smoke. Shower after work. Do not wear work clothes home. Use a vacuum equipped with a
HEPA filter to vacuum work clothes after they are worn. Launder them separately. Do not
shake or use compressed air to remove dust from work clothes.
6. Waste Disposal. Dispose of discarded linings, used rags, cloths and HEPA filters with
care, such as in sealed plastic bags. Consult applicable EPA, state and local regulations on
waste disposal.
Regulatory Guidance
References to OSHA, NIOSH, MSHA, and EPA, which are regulatory agencies in the United
States, are made to provide further guidance to employers and workers employed within the
United States. Employers and workers employed outside of the United States should consult
the regulations that apply to them for further guidance.
Advertisement
Table of Contents
