Setting The Avhd Device Skip Time; Setting The Hdmi™ Audio Mode; Setting The Time And Date - Toshiba TheaterWide 46HM95 Owner's Manual

Setting the AVHD device skip time

When you connect an external AVHD (audio/video hard drive)
device—such as the Toshiba Symbio™ AVHD Recorder—to
one of the TV's IEEE1394 ports, you can use the AVHD device
skip time feature to set the number of minutes the device will
skip forward or backward when you press the SKIP buttons.
Note:
• This TV will work best with the Toshiba
Recorder for recording high definition and standard definition
material from either tuner and for controlling live TV (pause/rewind/
etc.). When the Symbio AVHD Recorder is connected to the TV, the
remote control keys (LIVE, STOP, REW, PAUSE, PLAY, etc.) are
automatically activated to allow pausing of live TV.
• When you connect an AVHD (or D-VHS) device, the TV Guide
On Screen ® system is automatically configured to allow recording. See
page 23 for device connection information. See Chapters 5 and 7 for
details about setting up and using the TV Guide On screen
To set the AVHD device skip time:
1. Press MENU and open
the Setup menu.
2. Highlight AVHD Skip
Time and press •.
3. Press y or z to select
the AVHD skip time (1,
3, 5, or 15 minutes) and
press ENTER.
Setting the HDMI™ audio mode
To set the HDMI audio mode:
1. Press MENU and open
the Setup menu.
2. Highlight HDMI 1 (or
2) Audio and press •.
3. Press z or y to select
the HDMI audio mode
(Auto, Digital, or
Analog) and press
ENTER. (Auto is the
recommended mode). See "Connecting an HDMI or a
DVI device to the HDMI input" on page 19.
50
HM95_R1_044-52_061505 50
Black
Chapter 6: Setting up your TV
TM
AVHD
® system.
Setup
Installation
1 min
Sleep Timer
3 min
On/Off Timer
5 min
HDMI 1 Audio Auto
15 min
HDMI 2 Audio Auto
Slide Show Interval
2 Sec
AVHD Skip Time
15 min
Navigate Select CH RTN Back EXIT Exit
Setup
Installation
Auto
Sleep Timer Digital
On/Off Timer Analog
HDMI 1 Audio Auto
HDMI 2 Audio Auto
Slide Show Interval 2 Sec
AVHD Skip Time 15 min
Navigate Select CH RTN Back EXIT Exit
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.

Setting the time and date

Note: If you already set up the TV Guide On Screen
time and date were set automatically and you can skip this step.
To set the time and date:
1. Press MENU and open the Setup menu.
2. Highlight Installation and press ENTER. (A new set of
Installation menu icons will appear on-screen, as shown in
step 3 below.)
3. Open the Time And Date menu, highlight Start Setup, and
press ENTER.
Time And Date
Start Setup
Navigate Select CH RTN Back EXIT Exit
If you have not set up the TV Guide On Screen
the following screen will appear. To set the time, highlight
TV Guide On Screen ® and press ENTER. The TV Guide
On Screen ® setup sequence will start, and the time and date
will be set automatically.
Time And Date
Your TV Guide On Screen system can provide accurate
time and date information.
It is recommended you set up TV Guide On Screen
first and use it to obtain the time and date.
Manual TV Guide On Screen
If you have already set up the TV Guide On Screen
system, the time and date setting screen will appear and you
will need to manually set the time and date.
Time And Date
Date (MM/DD/YY)
0 6 3 0 / 0 5 /
Time (HH:MM) 1 1 1 1 AM :
Cancel Done
Note:
• If you highlight TV Guide On Screen
and date through the TV Guide On Screen
power outage occurs, the time and date will be updated
automatically when the power is restored.
• If you highlight Manual (above) to set the time and date
manually and a power outage occurs, you will lose the time
and date settings when the power is restored.
• If you manually set the time and date and then perform
TV Guide On Screen ® setup, the manual time and date settings
will be overridden by the TV Guide On Screen
6/24/05, 9:48 PM
® system, the
® system,
Cancel
®
®
(above) to set the time
®
system and a
® settings.