Windsor RRB 360 T Manual page 13

1 Fastening screw of the under-pressure
can
2 Fastening nut of the bulk waste flap
3 Screw of the roller brush crank
 Unscrew the fastening screws of the
vacuum socket and release the lever.
 Turn the fastening nut of the bulk waste
flap and unhook the bulk waste flap.
 Unscrew and withdraw bolt on the roller
brush swinging arm.
1 Cover
2 Roller brush
 Push the roller brush cover backwards
and remove it.
 Pull out roller brush.
 Push new roller brush into the roller
brush housing and onto the drive pin.
Note: When installing the new roller
brush, ensure correct positioning of the
bristle assembly.
Installation position of roller brush in direction of
travel
 Position roller brush cover.
 Fit the fastening screws and nuts.
 Hook the draw spring in.
 Screw on side panel.
 Push in the waste containers on both
the sides and lock them.
Adjusting and replacing sealing strips
 Park the sweeper on an even surface.
 Set programme switch to step 1 (driv-
ing). Roller brush is raised.
 Turn main key to "0" and remove it.
 Press emergency-stop button.
 Secure the machine with wheel
chock(s) to prevent it from rolling away.
 Raise slightly the waste containers on
both sides and pull them out.
 Open the fastening screws of the side
panels on both sides.
 Remove side panels.
 Front sealing flap
 Loosen retaining nuts for the front seal-
ing strip (1) slightly (to replace, un-
screw).
 Screw on new sealing strip without fully
tightening the nuts.
 Adjust side skirt.
 Set the distance between the sealing
strip and the floor so that the bottom
edge trails behind at a distance of be-
tween 0.4-0.6 in (10-15 mm).
 Tighten nuts.
 Rubber strip
 If worn, replace.
 Unscrew retaining nuts for the rubber
strip (2).
 Screw on new rubber strip.
 Rear flap
 Set the distance between the sealing
strip and the floor so that the bottom
edge trails behind at a distance of be-
tween 0.2 and 0.4 in (5 and 10 mm).
 If worn, replace.
 Unscrew retaining nuts for rear sealing
strip (3).
 Screw on new sealing strip.
 Side skirts
 Slightly loosen retaining nuts for the
side sealing strip (to replace, unscrew).
 Screw on new sealing strip without fully
tightening the nuts.
 To set the floor clearance, insert a
sheet with a thickness of between 0.04
and 0.12 in (1 and 3 mm) under the
sealing strip.
 Adjust side skirt.
 Tighten nuts.
 Screw on side panels.
 Push in the waste containers on both
the sides and lock them.
Check/replace dust filter
WARNING
Wear a dust mask when working around
the dust filter. Observe safety regulations
on the handling of fine particles.
Note: Wait at least 1 minute before remov-
ing the dust filter so that the dust can settle.
 Open the device hood.
12
-
US
1 Screws (2x)
2 Lid with cleaning device
3 Support
4 Dust filter (flat-fold filter)
 Loosen the screws.
 Fold the lid up and secure it by means
of the support.
 Take out the dust filter.
 Check dust filter, clean or replace
 Insert cleaned or new dust filter.
 Close the lid.
 Tighten the screws.
Check suction blower
 Check hose at the suction blower for
tightness.
Checking drive belt
 Turn main key to "0" and remove it.
 Press emergency-stop button.
 Open the device hood.
 Check tension of circular belt of the
side-brush; also check for wear or dam-
age.
 Check tension, wear and damages on
the V-belt of the sweep roller drive.
13