Firmware Updates - Extron electronics IN1804 Series Setup Manual
Hide thumbs
Also See for IN1804 Series:
- Setup manual (4 pages) ,
- User manual (110 pages) ,
- User manual (113 pages)
Advertisement
E
MENU and ENTER buttons — Press these buttons to access and navigate the on-screen display menu system.
F
Navigation buttons — Press these arrow buttons to navigate through the on-screen menu system or change settings.
Configuring the IN1804 Series
On-screen Display (OSD) Menu System
To configure IN1804 scalers using the OSD menu, connect a display device
and press the MENU button to open the OSD menu. The OSD menu consists
of eight submenus accessed using the front panel MENU or ENTER button.
Extron Product Configuration Software
To configure IN1804 scalers using PCS, install the software (available on
the Extron website, www.extron.com) to a PC connected to the scaler
via Ethernet or front panel USB Config port. After the installation, start the
program. For full instructions, press <F1> on the keyboard or click the ?
button in the software and select Help File.
Basic SIS Commands
To configure IN1804 scalers with specific SIS commands via an
RS-232, USB, or Ethernet connection, use the Extron DataViewer utility
or a control system to send and receive SIS commands. The table
below lists a selection of SIS commands. For a full list of SIS commands and variables, see the IN1804 Series User Guide at
www.extron.com.
Command
Select video input
View current input
Mute video (global)
Mute video and sync (global)
Unmute video and sync (global)
NOTE:
By default, video is unmuted after a power cycle.
Enable global output audio mute
Disable global audio mute
Enable front panel lock mode 1
Enable front panel lock mode 2
Enable front panel lock mode 3
Disable front panel lock mode
Set Auto-Switch mode
View Auto-Switch mode
Set user Auto-Switch priority
View user Auto-Switch priority
KEY:
X!
=
Input selection (1-4)
X3)
Auto-Switch mode: 0 = disabled (default), 1 = user defined priority, 2 = input memory priority (most recently detected input)
=
X3!
Input numbers for Auto-Switch priority: 1 = input 1, 2 = input 2, 3 = input 3, 4 = input 4
=
Firmware Updates
Download firmware updates from the Extron website and upload them via the internal web pages, PCS, or the Extron Firmware
Loader program.
4
©
2019 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners.
ASCII Command
Response
X!
!
In
X! •
!
X!]
1B
Vmt1
]
2B
Vmt2
]
0B
Vmt0
]
1Z
Amt1
]
0Z
]
Amt0
1X
Exe1
]
2X
Exe2
]
3X
Exe3
]
0X
]
Exe0
E X3)
AUSW
}
Ausw
X3)]
E
AUSW
}
X3)]
E
P
X3!
X3!
AUSW
}
Ausw P
...
1
4
E
P AUSW
}
X3!
1
...
Additional Description
All
]
Select video and audio from input
View currently selected source
Mute the video on all outputs.
Mute the video and sync on all outputs.
Unmute the video and sync on all outputs.
Mute the audio on all outputs.
Unmute the audio on all outputs.
Lock the entire front panel.
Lock the front panel except input switching, Auto-Image,
and output resolution reset (via down arrow button only).
Lock the front panel except input switching.
Allow all front panel adjustments and selections.
Select Auto-Switch mode
View the current Auto-Switch mode.
X3!
X3!
]
X3!
...
Set priority
1
4
order of priority, from highest to lowest.
View user Auto-Switch priority. Lists inputs in order of
X3!
]
4
priority, from highest to lowest.
X!
.
X!
.
X3)
.
for auto-input switching. Lists inputs in
68-3274-50 Rev. B
www.extron.com
10 19
Advertisement
