Advertisement
6.0
- VEHICLE CODE PROGRAMMING
The system must be configured according to the specific vehicle model on which it is to be installed.
To
help you understand the coding procedure, here below is an example illustrating the configuration
procedure. In this case the code to be entered is 1-0-3.
A separate leaflet, included in the alarm packaging, lists all the available vehicles (codes
are updated at packaging time).
!
Up-to-date information on supported vehicle models can be found in the restricted area
of our website:
The alarm has an indicator LED that signals any wrong vehicle code inserted.
The code must range between 100 and 235 otherwise the LED on the unit blinks
repeatedly and the procedure is interrupted.
The previously inserted code remains stored.
!
The procedure is also invalidated if the LED blinks more than 10 times. In this case
there is no optical warning, the procedure is simply interrupted.
In either case, repeat the whole procedure.
Connect the wiring harness connectors to the corresponding alarm connectors.
Press and hold the button shown below until the LED lights up.
Release the button, the LED
The LED will start flashing after 3 to 4 seconds; count the flashes.
In this case press the button at the 1st flash which corresponds to number "1".
After 4 seconds, the LED will flash for the second time.
Press the button at the 10th flash which corresponds to number "0".
After 4 more seconds, the LED will flash for the third and last time.
Press the button at the 3rd flash which corresponds to number "3".
When the last digit is entered, the alarm system "repeats" the entered code:
• 1 FLASH +
A SHORT PAUSE
• 10 FLASHES +
A SHORT PAUSE
• 3 FLASHES
Press the vehicle remote control lock/unlock buttons to make sure the alarm system works properly.
If needed, disconnect the 8-pin connector and reconnect it after a few seconds.
PAGE 08
www.gemini-alarm.com
.
will switch OFF.
3-4 seconds
1st FLASH
FLASH
10th
3rd FLASH
The table below applies to the system programmed in "standard configuration".
Every time you enter in programming mode, the alarm system resets to the default settings.
A lack of power during electrical system maintenance, will not affect the programming.
SELECTABLE FUNCTIONS
Arming/disarming optical signals
Arming/disarming acoustic signals
This function activates the optical signals (turn indicator flashes) that confirm system
arming/disarming
.
If the vehicle already has optical lock/unlock signals, the turn indicators alarm flashes
!
This function activates the acoustic signals (siren chirps) that confirm system arming/disarming
This function arms the system 60 sec. after ignition is switched OFF and the last door is opened and
closed.
Opening a door during the 60-second passive arming countdown
interrupt; it will resume once the door is closed
This function modifies the alarm input signal (positive or negative) according to the signal generated
by the
door switch.
If this feature is enabled, 2 unlocking pulses will be supplied to unlock all doors at the same time.
Press
This is useful in case separate actions are required to open the driver door and then the other doors.
DOUBLE PULSE UNLOCK QUICK ACTIVATION:
- Disconnect the alarm system power supply and ground the Green/Black wire.
- Connect the alarm power supply; 3 quick high-pitched chirps will confirm operation.
Press
- Remove the Green/Black wire from ground.
NB:
To reset the default setting, repeat the above steps; 1 low-pitched chirp will confirm the operation.
Press Gemini remote control button "
Press
To enter in programming mode proceed as follows:
• With the alarm system disarmed, turn ignition key "ON".
• Wait approx. 2 sec. for the LED to light up.
• While the LED is ON, press remote control button "ON".
7.0 - SYSTEM PROGRAMMING
S
System passive arming
Door input - positive
Double pulse unlock
7.1
- OPTICAL SIGNALS
should be disabled.
7.2
- ACOUSTIC SIGNALS
7.3
- PASSIVE ARMING
.
7.4 -
DOOR SWITCH POLARITY SELECTION
7.5 - D
OUBLE PULSE UNLOCK
8.0 - SYSTEM PROGRAMMING EXAMPLE
ON
" to enable programmable functions and button
"
OFF
" to disable them.
STATUS
LED FLASHES
Enabled
Enabled
Disabled
Disabled
Disabled
.
will cause the procedure to
PAGE 09
Advertisement
