Related Manuals for Kargo Master 4A873
Summary of Contents for Kargo Master 4A873
- Page 1 Instruction Guide 4A873 Kargo Master Rancho Cordova, CA 95742 800-343-7486 CustomerService@KargoMaster.com DATE: ______________...
-
Page 2: Table Of Contents
Instructions – 4A873 *PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING, INSTALLING, AND USING THIS PRODUCT* Warning Always check for wires, fuel tanks and lines, brake lines and other important vehicle functionality items prior to drilling and installing all products. -
Page 3: Parts List
Instructions – 4A873 Parts For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 2... -
Page 4: Assembly Hardware
Instructions – 4A873 Assembly Hardware For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 3... - Page 5 Instructions – 4A873 Assembly Hardware (con’t) For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 4...
-
Page 6: Install Hardware
Instructions – 4A873 Installation Hardware For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 5... -
Page 7: Promaster City
Instructions – 4A873 DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF Promaster City Installation • Locate 6 mounting locations shown on roof of van. • Install “Top Rail” as shown using M6x20mm bolts with lock washers and flat washers. • Be sure to put rubber washer between the “Top Rail”... -
Page 8: Nv200/City Express
Instructions – 4A873 DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF NV200/City Express Installation • Locate 4 mounting locations shown on roof of van. • Install “Top Rail” as shown using M8x25mm bolts with lock washers and flat washers. • Mount rail so there is about 1”... -
Page 9: Transit Connect
Instructions – 4A873 DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF Transit Connect Installation • Locate 4 mounting locations shown on roof of van. • Be sure to put rubber washer between the “Top Rail” and the roof to ensure sealing. -
Page 10: Step 1 - Assembly Of Foot
Instructions – 4A873 Assembly Instructions Step 1 – Assembly of Foot • Measure width between previously installed rails. • On the cross bows, use the slots that correspond to the measured distance between rails. • Bolt feet to bows as shown, DO NOT TIGHTEN at this point. -
Page 11: Step 3 - Mount To Rails
Instructions – 4A873 Step 3 – Mount to Rails • Place both bows on top of installed rails. • Have the ladder hooks on the driver side of vehicle. • Snug Tighten, but allow movement Step 4 – Assemble Side Tube •... -
Page 12: Step 5 - Mount Side Tube
Instructions – 4A873 Step 5 – Mount Side Tube • Place side tube on top of installed bows. • Have the bend towards the front of the vehicle as shown. • Mount rotation bar plate to tube as shown. • Leave one square slot open at the rear. -
Page 13: Step 6 - Clamp Tube
Instructions – 4A873 Step 6 – Clamp Tube • Place clamp and lock L bracket on top of installed bows. • Insert plastic bushings into the clamp and lock L bracket and the rotation bar plate installed in Step 5, with flange towards each other and to the inside as shown. -
Page 14: Step 7 - Handle
Instructions – 4A873 • Bolt clamp and lock L bracket to bows using 3/8 x 1 carriage bolt, 3/8 flat washer and a 3/8 nylock as shown. (This view shown without clamp tube) • TIGHTEN Step 7 – Handle • Bolt handle to clamp tube using a 5/16 x 2.75 hex head, two 5/16” flat washers, 5/16 nylon washer and 5/16 a nylock. -
Page 15: Step 8 - Latch Assembly
Instructions – 4A873 Step 8 – Latch Assembly • Bolt latch to the rear of the mount tube that was installed in Step 5 using 5/16 x 1.75 carriage bolt, 5/16 curved washer and a 5/16 nylock. • TIGHTEN Step 9 – Ladder Hook •... -
Page 16: Step 10 - Ladder Hook To Bracket
Instructions – 4A873 Step 10 – Ladder Hook to Bracket • Bolt ladder hook to the ladder hook bracket in the orientation shown using a 3/8 flat washer and a 3/8 nylock. • Snug Tighten, but allow movement. • Final location will be determined once ladder is placed on rack Step 11 –...