Page 1 Products Solutions Services GP01088D/06/EN/02.17 71376168 Valid as of version 01.01.zz (Device firmware) Description of Device Parameters Proline Cubemass 300 Modbus RS485 Coriolis flowmeter Menu/Variable Proline Device Access status tooling: Operation Setup Diagnostics Expert Locking status: Access status tooling: Enter access code:...
Page 3: Table Of Contents
Proline Cubemass 300 Modbus RS485 Table of contents Table of contents 3.7.3 "Petroleum" submenu ... . 182 About this document ....4 "Diagnostics"...
Page 4: About This Document
About this document Proline Cubemass 300 Modbus RS485 About this document Document function The document is part of the Operating Instructions and serves as a reference for parameters, providing a detailed explanation of each individual parameter of the Expert operating menu.
Page 5 Proline Cubemass 300 Modbus RS485 About this document Operating menu for operators and maintenances Language Language Operatation Parameter 1 Parameter n Submenu 1 Submenu n Setup Device tag Wizard 1 / Parameter 1 Wizard n / Parameter n Advanced setup...
Page 6: Structure Of A Parameter Description
About this document Proline Cubemass 300 Modbus RS485 1.3.2 Structure of a parameter description The individual parts of a parameter description are described in the following section: Complete parameter name Write-protected parameter = Navigation Navigation path to the parameter via the local display (direct access code) or web browser...
Page 7: Symbols In Graphics
Proline Cubemass 300 Modbus RS485 About this document 1.4.2 Symbols in graphics Symbol Meaning Symbol Meaning 1, 2, 3 ... Item numbers A, B, C, ... Views A-A, B-B, C-C, ... Sections Documentation 1.5.1 Standard documentation Operating Instructions Measuring device...
Page 8: Overview Of The Expert Operating
Overview of the Expert operating menu Proline Cubemass 300 Modbus RS485 Overview of the Expert operating menu The following table provides an overview of the menu structure of the expert operating menu and its parameters. The page reference indicates where the associated description of the submenu or parameter can be found.
Page 9 Proline Cubemass 300 Modbus RS485 Overview of the Expert operating menu I/O 1 type (3901–1) →  102 Apply I/O config (3907) →  102 Alteration code (2762) →  103 ‣ Input →  103 ‣ Current input 1 to n →...
Page 10 Overview of the Expert operating menu Proline Cubemass 300 Modbus RS485 Operating time (0652) →  185 ‣ Diagnostic list →  186 ‣ Event logbook →  190 ‣ Device info →  192 ‣ →  196 Mainboard module ‣...
Page 11: Description Of Device Parameters
Proline Cubemass 300 Modbus RS485 Description of device parameters Description of device parameters In the following section, the parameters are listed according to the menu structure of the local display. Specific parameters for the operating tools are included at the appropriate points in the menu structure.
Page 12 Description of device parameters Proline Cubemass 300 Modbus RS485 00914-2 A0029414 Direct access code Note the following when entering the direct access code: • The leading zeros in the direct access code do not have to be entered. Example: Enter "914" instead of "00914"...
Page 13: System" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Access status Navigation  Expert → Access status (0005) Description Displays the access authorization to the parameters via the local display, Web browser or operating tool. User interface • Operator • Maintenance...
Page 14: Display" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 3.1.1 "Display" submenu Navigation  Expert → System → Display ‣ Display Display language (0104) →  15 Format display (0098) →  15 →  18 Value 1 display (0107) 0% bargraph 1 (0123) →...
Page 15 Proline Cubemass 300 Modbus RS485 Description of device parameters Display language Navigation  Expert → System → Display → Display language (0104) Prerequisite A local display is provided. Description Use this function to select the configured language on the local display.
Page 16 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description The display format (size, bar graph etc.) and number of measured values displayed simultaneously (1 to 4) can be configured. This setting only applies to normal operation. • The Value 1 display parameter (→  18) to Value 4 display parameter (→...
Page 17 Proline Cubemass 300 Modbus RS485 Description of device parameters Possible measured values shown on the local display: "1 value, max." option X X X X X X X 900.00 kg/h A0013099 "Bargr. + 1 value" option X X X X X X X 900.00 kg/h...
Page 18 Description of device parameters Proline Cubemass 300 Modbus RS485 Value 1 display  Navigation  Expert → System → Display → Value 1 display (0107) Prerequisite A local display is provided. Description Use this function to select one of the measured values to be shown on the local display.
Page 19 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description If several measured values are displayed at once, the measured value selected here will be the first value to be displayed. The value is only displayed during normal operation.
Page 20 Description of device parameters Proline Cubemass 300 Modbus RS485 100% bargraph 1  Navigation  Expert → System → Display → 100% bargraph 1 (0125) Prerequisite A local display is provided. Description Use this function to enter the 100% bar graph value to be shown on the display for the measured value 1.
Page 21 Proline Cubemass 300 Modbus RS485 Description of device parameters Description Use this function to select one of the measured values to be shown on the local display. Selection • None • Mass flow • Volume flow • Correct.vol.flow • Target mass flow •...
Page 22 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description If several measured values are displayed at once, the measured value selected here will be the second value to be displayed. The value is only displayed during normal operation.
Page 23 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description If several measured values are displayed at once, the measured value selected here will be the third value to be displayed. The value is only displayed during normal operation.
Page 24 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description The Format display parameter (→  15) is used to specify that the measured value is to be displayed as a bar graph. User entry The unit of the displayed measured value is taken from the System units submenu (→...
Page 25 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description If several measured values are displayed at once, the measured value selected here will be the fourth value to be displayed. The value is only displayed during normal operation.
Page 26 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description This type of alternating display only occurs automatically if the number of measured values defined exceeds the number of values the selected display format can display simultaneously. • The Value 1 display parameter (→  18) to Value 4 display parameter (→  24) are used to specify which measured values are shown on the local display.
Page 27 Proline Cubemass 300 Modbus RS485 Description of device parameters XXXXXXXXX A0029422 Position of the header text on the display Selection • Device tag Is defined in the Device tag parameter (→  193). • Free text Is defined in the Header text parameter (→  27).
Page 28: Configuration Backup" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Description Use this function to select the decimal separator. Selection • . (point) • , (comma) Factory setting . (point) Contrast display Navigation  Expert → System → Display → Contrast display (0105) Prerequisite A local display is provided.
Page 29 Proline Cubemass 300 Modbus RS485 Description of device parameters Last backup →  29 Config. managem. →  29 Backup state →  30 Compar. result →  30 Operating time Navigation  Expert → System → Config. backup → Operating time (0652) Description Use this function to display the length of time the device has been in operation.
Page 30 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Selection Options Description Cancel No action is executed and the user exits the parameter. Execute backup A backup copy of the current device configuration is saved from the HistoROM backup to the memory of the device.
Page 31: Diagn. Handling" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters • Backup corrupt • Check not done • Dataset incomp. Factory setting Check not done Additional information Description The comparison is started via the Compare option in the Config. managem. parameter (→  29).
Page 32 Description of device parameters Proline Cubemass 300 Modbus RS485 Alarm delay  Navigation  Expert → System → Diagn. handling → Alarm delay (0651) Description Use this function to enter the time interval until the device generates a diagnostic message.
Page 33 Proline Cubemass 300 Modbus RS485 Description of device parameters Navigation  Expert → System → Diagn. handling → Diagn. behavior ‣ Diagn. behavior Diagnostic no. 046 (0709) →  34 Diagnostic no. 140 (0708) →  34 Diagnostic no. 144 (0731) →...
Page 34 Description of device parameters Proline Cubemass 300 Modbus RS485 Diagnostic no. 046 (Sensor limit)  Navigation  Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 046 (0709) Description Option for changing the diagnostic behavior of the diagnostic message 046 Sensor limit.
Page 35 Proline Cubemass 300 Modbus RS485 Description of device parameters Diagnostic no. 374 (Sensor electron.)  Navigation  Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 374 (0710) Description Option for changing the diagnostic behavior of the diagnostic message 374 Sensor electron..
Page 36 Description of device parameters Proline Cubemass 300 Modbus RS485 Diagnostic no. 442 (Freq. output 1 to n)  Navigation  Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 442 (0658) Prerequisite The measuring device has a pulse/frequency/switch output.
Page 37 Proline Cubemass 300 Modbus RS485 Description of device parameters Selection • Off • Alarm • Warning • Logbook only Factory setting Warning Additional information For a detailed description of the options available, see →  32 Diagnostic no. 543 (Double pulse out) ...
Page 38 Description of device parameters Proline Cubemass 300 Modbus RS485 Diagnostic no. 831 (Sensor temp.)  Navigation  Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 831 (0641) Description Use this function to change the diagnostic behavior of the diagnostic message 831 Sensor temp..
Page 39 Proline Cubemass 300 Modbus RS485 Description of device parameters Diagnostic no. 834 (Process temp.)  Navigation  Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 834 (0700) Description Use this function to change the diagnostic behavior of the diagnostic message 834 Process temp..
Page 40 Description of device parameters Proline Cubemass 300 Modbus RS485 Diagnostic no. 912 (Medium inhomog.)  Navigation  Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 912 (0703) Description Option for changing the diagnostic behavior of the diagnostic message 912 Medium inhomog..
Page 41: Administration" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Diagnostic no. 948 (Oscill. damping)  Navigation  Expert → System → Diagn. handling → Diagn. behavior → Diagnostic no. 948 (0744) Description Option for changing the diagnostic behavior of the diagnostic message 948 Oscill.
Page 42 Once the access code has been defined, write-protected parameters can only be modified if the access code is entered in the Ent. access code parameter (→  13). If you lose the access code, please contact your Endress+Hauser sales organization. User entry A message is displayed if the access code is not in the input range.
Page 43 Character string comprising numbers, letters and special characters Factory setting 0x00 Additional information Description For a reset code, contact your Endress+Hauser service organization. User entry The reset code can only be entered via: • Web browser • DeviceCare, FieldCare (via interface CDI RJ45) •...
Page 44 Additional information Description If a measuring device was ordered with an additional software option, the activation code is programmed in the device at the factory. User entry To activate a software option subsequently, please contact your Endress+Hauser sales organization. NOTE! Endress+Hauser...
Page 45 ▸ Before you enter a new activation code, make a note of the current activation code . ▸ Enter the new activation code provided by Endress+Hauser when the new software option was ordered. ▸ Once the activation code has been entered, check if the new software option is displayed in the SW option overv.
Page 46: Sensor" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description Displays all the options that are available if ordered by the customer. "Extend. HistoROM" option Order code for "Application package", option EA "Extended HistoROM" "HBT Verification" option and "HBT Monitoring" option Order code for "Application package", option EB "Heartbeat Verification + Monitoring"...
Page 47 Proline Cubemass 300 Modbus RS485 Description of device parameters ‣ Input values →  54 ‣ Output values →  55 "Process variab." submenu Navigation  Expert → Sensor → Measured val. → Process variab. ‣ Process variab. Mass flow (1838) →...
Page 48 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Dependency The unit is taken from the Mass flow unit parameter (→  60) Volume flow Navigation  Expert → Sensor → Measured val. → Process variab. → Volume flow (1847) Description Displays the volume flow currently calculated.
Page 49 Proline Cubemass 300 Modbus RS485 Description of device parameters Ref.density Navigation  Expert → Sensor → Measured val. → Process variab. → Ref.density (1852) Description Displays the reference density currently calculated. User interface Signed floating-point number Additional information Dependency The unit is taken from the Ref. dens. unit parameter (→  66)
Page 50 Description of device parameters Proline Cubemass 300 Modbus RS485 Description Displays the concentration currently calculated. User interface Signed floating-point number Additional information Dependency The unit is taken from the Concentr. unit parameter (0613). Target mass flow Navigation  Expert → Sensor → Measured val. → Process variab. → Target mass flow (1864)
Page 51 Proline Cubemass 300 Modbus RS485 Description of device parameters Targ.corr.vol.fl Navigation  Expert → Sensor → Measured val. → Process variab. → Targ.corr.vol.fl (1893) Prerequisite With the following conditions: • Order code for "Application package", option ED "Concentration" • The WT-% option or the User conc. option is selected in the Concentr. unit parameter.
Page 52 Description of device parameters Proline Cubemass 300 Modbus RS485 User interface Signed floating-point number Additional information Dependency The unit is taken from the Volume flow unit parameter (→  61) Carrier vol. fl. Navigation  Expert → Sensor → Measured val. → Process variab. → Carrier vol. fl. (1896)
Page 53 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description As it is only possible to display a maximum of 7 digits in the operating tool, the current counter value is the sum of the totalizer value and the overflow value from the Tot.
Page 54 Description of device parameters Proline Cubemass 300 Modbus RS485 "Input values" submenu Navigation  Expert → Sensor → Measured val. → Input values ‣ Input values ‣ Current input 1 to n →  54 ‣ Val.stat.inp. 1 to n →...
Page 55 Proline Cubemass 300 Modbus RS485 Description of device parameters "Value status input 1 to n" submenu Navigation  Expert → Sensor → Measured val. → Input values → Val.stat.inp. 1 to n ‣ Val.stat.inp. 1 to n Val.stat.inp. (1353–1 to n) →...
Page 56 Description of device parameters Proline Cubemass 300 Modbus RS485 Output curr. 1 to n Navigation  Expert → Sensor → Measured val. → Output values → Value curr.out 1 to n → Output curr. 1 to n (0361–1 to n) Description Displays the current value currently calculated for the current output.
Page 57 Proline Cubemass 300 Modbus RS485 Description of device parameters Pulse output 1 to n Navigation  Expert → Sensor → Measured val. → Output values → PFS output 1 to n → Pulse output 1 to n (0456–1 to n) Prerequisite In the Operating mode parameter (→...
Page 58 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information User interface • Open The switch output is not conductive. • Closed The switch output is conductive. "Relay output 1 to n" submenu Navigation  Expert → Sensor → Measured val. → Output values → Relay output 1 to n ‣...
Page 59: System Units" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Max. cycles no. Navigation  Expert → Sensor → Measured val. → Output values → Relay output 1 to n → Max. cycles no. (0817–1 to n) Description Displays the maximum number of guaranteed switch cycles.
Page 60 Description of device parameters Proline Cubemass 300 Modbus RS485 Volume unit (0563) →  63 Cor.volflow unit (0558) →  64 Corr. vol. unit (0575) →  64 Density unit (0555) →  65 →  66 Ref. dens. unit (0556) Temperature unit (0557) →...
Page 61 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Result The selected unit applies for: • Target mass flow parameter (→  50) • Carrier mass fl. parameter (→  50) • Mass flow parameter (→  47) Selection For an explanation of the abbreviated units: →...
Page 62 Description of device parameters Proline Cubemass 300 Modbus RS485 Selection SI units US units Imperial units • cm³/s • af/s • gal/s (imp) • cm³/min • af/min • gal/min (imp) • cm³/h • af/h • gal/h (imp) • cm³/d • af/d •...
Page 63 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Result The selected unit applies for: Volume flow parameter (→  48) Selection For an explanation of the abbreviated units: →  232 Customer-specific units The unit for the customer-specific volume is specified in the Volume text parameter (→...
Page 64 Description of device parameters Proline Cubemass 300 Modbus RS485 Cor.volflow unit  Navigation  Expert → Sensor → System units → Cor.volflow unit (0558) Description Use this function to select the unit for the corrected volume flow. Selection SI units...
Page 65 Proline Cubemass 300 Modbus RS485 Description of device parameters Density unit  Navigation  Expert → Sensor → System units → Density unit (0555) Description Use this function to select the unit for the density. Selection SI units US units Imperial units •...
Page 66 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Result The selected unit applies for: • Density setpt 1 parameter • Density setpt 2 parameter • Density parameter (→  48) Selection • SD = specific density The specific density is the ratio of the medium density to the water density at a water temperature of +4 °C (+39 °F), +15 °C (+59 °F), +20 °C (+68 °F).
Page 67 Proline Cubemass 300 Modbus RS485 Description of device parameters Temperature unit  Navigation  Expert → Sensor → System units → Temperature unit (0557) Description Use this function to select the unit for the temperature. Selection SI units US units •...
Page 68 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Result The unit is taken from: • Pressure value parameter (→  88) • External press. parameter (→  88) • Pressure value parameter (→  49) Selection For an explanation of the abbreviated units: →  232 Date/time format ...
Page 69: Volume Text (0567)
Proline Cubemass 300 Modbus RS485 Description of device parameters Corr vol. offset (0602) →  72 Cor.vol. factor (0590) →  72 Density text (0570) →  73 Density offset (0571) →  73 Density factor (0572) →  73 Spec.
Page 70: Volume Offset (0569)
Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Result The defined unit is shown as an option in the choose list of the following parameters: • Volume flow unit parameter (→  61) • Volume unit parameter (→  63) Example If the text GLAS is entered, the choose list of the Volume flow unit parameter (→...
Page 71: Mass Offset (0562)
Proline Cubemass 300 Modbus RS485 Description of device parameters User entry Max. 10 characters such as letters, numbers or special characters (@, %, /) Factory setting User mass Additional information Result The defined unit is shown as an option in the choose list of the following parameters: •...
Page 72: Corr. Vol. Text (0592)
Description of device parameters Proline Cubemass 300 Modbus RS485 Corr. vol. text  Navigation  Expert → Sensor → System units → User-spec. units → Corr. vol. text (0592) Description Use this function to enter a text for the user-specific unit of the corrected volume and corrected volume flow.
Page 73 Proline Cubemass 300 Modbus RS485 Description of device parameters Density text  Navigation  Expert → Sensor → System units → User-spec. units → Density text (0570) Description Use this function to enter a text or the user-specific unit of density.
Page 74 Description of device parameters Proline Cubemass 300 Modbus RS485 Factory setting User enth. Additional information Result Example If the text CAL is entered, the choose list of the Cal. value unit parameter shows the following options: • CAL/Nm3 • CAL/m3 •...
Page 75 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Result The defined unit is shown as an option in the choose list of the following parameters: • Energy unit parameter • Energy flow unit parameter Example If the text W is entered, the choose list of the Energy flow unit parameter shows the following options: •...
Page 76: Process Param." Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Result The defined unit is shown as an option in the choose list of the Pressure unit parameter (→  67). Pressure offset  Navigation  Expert → Sensor → System units → User-spec. units → Pressure offset (0580) Description Use this function to enter the offset for adapting the user-specific pressure unit.
Page 77 Proline Cubemass 300 Modbus RS485 Description of device parameters ‣ Low flow cut off →  79 ‣ Partial pipe det →  82 Flow damping  Navigation  Expert → Sensor → Process param. → Flow damping (1802) Description Use this function to enter a time constant for flow damping (PT1 element).
Page 78 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description The damping is performed by a PT1 element User entry • Value = 0: no damping • Value > 0: damping is increased Damping is switched off if 0 is entered (factory setting).
Page 79 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description Flow override is active • The diagnostic message diagnostic message C453 Flow override is displayed. • Output values – Temperature: proceeding output – Totalizers 1-3: Stop being totalized Positive zero return can also be enabled via the Status input: Assign stat.inp.
Page 80 Description of device parameters Proline Cubemass 300 Modbus RS485 Description Use this function to enter a switch-on value for low flow cut off. Low flow cut off is activated if the value entered is not equal to 0 →  80.
Page 81 Proline Cubemass 300 Modbus RS485 Description of device parameters Pres. shock sup.  Navigation  Expert → Sensor → Process param. → Low flow cut off → Pres. shock sup. (1806) Prerequisite One of the following options is selected in the Assign variable parameter (→  79): •...
Page 82 Description of device parameters Proline Cubemass 300 Modbus RS485 A0012888 Flow Time Drip Pressure shock Pressure shock suppression active as specified by the time entered Pressure shock suppression inactive Valve closes Flow falls below the on-value of the low flow cut off: pressure shock suppression is activated...
Page 83 Proline Cubemass 300 Modbus RS485 Description of device parameters Assign variable  Navigation  Expert → Sensor → Process param. → Partial pipe det → Assign variable (1860) Description Use this function to select a process variable to detect empty or partially filled measuring tubes.
Page 84 Description of device parameters Proline Cubemass 300 Modbus RS485 Description Use this function to enter an upper limit value to enable detection of empty or partially filled measuring tubes. If the measured density exceeds this value, detection is enabled. User entry...
Page 85: Measurement Mode" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters diagnostic message S862 Partly filled. In the case of non-homogeneous media or air pockets, the damping of the measuring tubes increases. User entry • Damping is disabled if 0 is entered (factory setting).
Page 86 Description of device parameters Proline Cubemass 300 Modbus RS485 Selection • Liquid • Gas Factory setting Liquid Select gas type  Navigation  Expert → Sensor → Measurement mode → Select gas type (6074) Prerequisite The Gas option is selected in the Select medium parameter (→  85).
Page 87: External Comp." Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters User entry 1 to 99 999.9999 m/s Factory setting 415.0 m/s Temp. coeff. SV  Navigation  Expert → Sensor → Measurement mode → Temp. coeff. SV (6181) Prerequisite The Others option is selected in the Select gas type parameter (→  86).
Page 88 Description of device parameters Proline Cubemass 300 Modbus RS485 Selection • Off • Fixed value • External value • Current input 1 • Current input 2 Factory setting Additional information Selection • Fixed value A fixed pressure value is used for compensation: Pressure value parameter (→  88) •...
Page 89 Proline Cubemass 300 Modbus RS485 Description of device parameters Temp.corr.source  Navigation  Expert → Sensor → External comp. → Temp.corr.source (6184) Description Use this function to select the temperature mode. Selection • Internal value • External value • Current input 1 •...
Page 90: Calculated Value" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Selection • Internal value • External value Factory setting Internal value 3.2.6 "Calculated value" submenu Navigation  Expert → Sensor → Calculated value ‣ Calculated value ‣ →  90 Corr. vol.flow.
Page 91 Proline Cubemass 300 Modbus RS485 Description of device parameters Factory setting Calc ref density Additional information Selection The Ref. dens API 53 option is suitable only for applications involving LPG , where the flow rate is measured on the basis of the corrected volume flow.
Page 92 Description of device parameters Proline Cubemass 300 Modbus RS485 Ref. temperature  Navigation  Expert → Sensor → Calculated value → Corr. vol.flow. → Ref. temperature (1816) Prerequisite The Calc ref density option is selected in the Corr. vol.flow. parameter (→  90).
Page 93: Sensor Adjustment" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Square exp coeff  Navigation  Expert → Sensor → Calculated value → Corr. vol.flow. → Square exp coeff (1818) Prerequisite The Calc ref density option is selected in the Corr. vol.flow. parameter (→  90) parameter.
Page 94 Description of device parameters Proline Cubemass 300 Modbus RS485 "Zero point adj." submenu • It is generally not necessary to perform zero point adjustment. • However, this function may be needed in some applications with low flow and strict accuracy requirements.
Page 95 Proline Cubemass 300 Modbus RS485 Description of device parameters Progress Navigation  Expert → Sensor → Sensor adjustm. → Zero point adj. → Progress (2808) Description The progress of the process is indicated. User interface 0 to 100 % "Variable adjust" submenu Navigation ...
Page 96 Description of device parameters Proline Cubemass 300 Modbus RS485 User entry Signed floating-point number Factory setting 0 kg/s Additional information Description Corrected value = (factor × value) + offset Mass flow factor  Navigation  Expert → Sensor → Sensor adjustm. → Variable adjust → Mass flow factor (1832) Description Use this function to enter a quantity factor (without time) for the mass flow.
Page 97 Proline Cubemass 300 Modbus RS485 Description of device parameters Factory setting Additional information Description Corrected value = (factor × value) + offset Density offset  Navigation  Expert → Sensor → Sensor adjustm. → Variable adjust → Density offset (1848) Description Use this function to enter the zero point shift for the density trim.
Page 98 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description Corrected value = (factor × value) + offset Corr. vol factor  Navigation  Expert → Sensor → Sensor adjustm. → Variable adjust → Corr. vol factor (1867) Description Use this function to enter a quantity factor (without time) for the corrected volume flow.
Page 99: Calibration" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description Corrected value = (factor × value) + offset Temp. offset  Navigation  Expert → Sensor → Sensor adjustm. → Variable adjust → Temp. offset (1870) Description Use this function to enter the zero point shift for the temperature trim. The temperature unit on which the shift is based is K.
Page 100 Description of device parameters Proline Cubemass 300 Modbus RS485 Nominal diameter (2807) →  100 C0 to 5 (6022) →  101 Cal. factor Navigation  Expert → Sensor → Calibration → Cal. factor (6025) Description Displays the current calibration factor for the sensor.
Page 101: I/O Configuration" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters C0 to 5 Navigation  Expert → Sensor → Calibration → C0 to 5 (6022) Description Displays the current density coefficients C0 to 5 of the sensor. User interface Signed floating-point number Factory setting "I/O configuration"...
Page 102 Description of device parameters Proline Cubemass 300 Modbus RS485 User interface • Not plugged • Invalid • Not configurable • Configurable • MODBUS Additional information "Not plugged" option The I/O module is not plugged in. "Invalid" option The I/O module is not plugged correctly.
Page 103: Input" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Selection • No • Yes Factory setting Alteration code  Navigation  Expert → I/O config. → Alteration code (2762) Description Use this function to enter the ordered activation code to activate the I/O configuration change.
Page 104 Description of device parameters Proline Cubemass 300 Modbus RS485 Failure mode (1601–1 to n) →  106 Failure value (1602–1 to n) →  106 Terminal no. Navigation  Expert → Input → Current input 1 to n → Terminal no. (1611–1 to n) Description Displays the terminal numbers used by the current input module.
Page 105 Proline Cubemass 300 Modbus RS485 Description of device parameters Factory setting Country-specific: • 4...20 mA NAMUR • 4...20 mA US Additional information Examples Sample values for the current range: Current span parameter (→  111) 0/4 mA value  Navigation ...
Page 106: Status Input 1 To N" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Failure mode  Navigation  Expert → Input → Current input 1 to n → Failure mode (1601–1 to n) Description Use this function to select the input behavior when measuring a current outside the configured Current span parameter (→...
Page 107 Proline Cubemass 300 Modbus RS485 Description of device parameters Active level (1351–1 to n) →  108 Response time (1354–1 to n) →  108 Terminal no. Navigation  Expert → Input → Status input 1 to n → Terminal no. (1358–1 to n) Description Displays the terminal numbers used by the status input module.
Page 108: Output" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Val.stat.inp. Navigation  Expert → Input → Status input 1 to n → Val.stat.inp. (1353–1 to n) Description Displays the current input signal level. User interface • High • Low Active level ...
Page 109: Current Output 1 To N" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters ‣ Relay output 1 to n →  148 ‣ Double pulse out →  155 3.5.1 "Current output 1 to n" submenu Navigation  Expert → Output → Curr.output 1 to n ‣...
Page 110 Description of device parameters Proline Cubemass 300 Modbus RS485 User interface • Not used • 24-25 (I/O 2) • 22-23 (I/O 3) Additional information "Not used" option The current output module does not use any terminal numbers. Signal mode ...
Page 111 Proline Cubemass 300 Modbus RS485 Description of device parameters • Water mass flow • Oil volume flow • Water vol. flow • Oil corr.vol.fl. • Water corr.v.fl. • Concentration • Temperature • Carr. pipe temp. • Electronic temp. • Osc. freq. 0 •...
Page 112 Description of device parameters Proline Cubemass 300 Modbus RS485 I [mA] A0034351 Current span for process value Lower level for signal on alarm Upper level for signal on alarm Selection Options 4...20 mA NAMUR 3.8 to 20.5 mA < 3.6 mA >...
Page 113 Proline Cubemass 300 Modbus RS485 Description of device parameters Factory setting Country-specific: • 0 kg/h • 0 lb/min Additional information Description Positive and negative values are permitted depending on the process variable assigned in the Assign curr. parameter (→  110). In addition, the value can be greater than or smaller than the value assigned for the 20 mA current in the 20 mA value parameter (→...
Page 114 Description of device parameters Proline Cubemass 300 Modbus RS485 I [mA] A0013758 Current Flow Value assigned to the 0/4 mA current Forward flow Reverse flow The current output signal is independent of the direction of flow (absolute amount of the measured variable).
Page 115 Proline Cubemass 300 Modbus RS485 Description of device parameters smaller than the value assigned for the 0/4 mA current in the 0/4 mA value parameter (→  112). Dependency The unit depends on the process variable selected in the Assign curr. parameter (→...
Page 116 Description of device parameters Proline Cubemass 300 Modbus RS485 Description Use this function to select the measuring mode for the current output. Selection • Forward flow • Forward/Reverse • Rev. flow comp. Factory setting Forward flow Additional information Description The process variable that is assigned to the current output via the Assign curr.
Page 117 Proline Cubemass 300 Modbus RS485 Description of device parameters Flow values can aggregate in the buffer in the event of prolonged and unwanted fluid reverse flow. However, these flows are not taken into consideration by the current output configuration, i.e. the reverse flow is not compensated.
Page 118 Description of device parameters Proline Cubemass 300 Modbus RS485 I [mA] A0028093 Current Time With Rev. flow comp. option Flow components outside the span are buffered, balanced and output after a maximum delay of 60 s. I [mA] S = A...
Page 119 Proline Cubemass 300 Modbus RS485 Description of device parameters A0028098 Flow Time Lower range value (value assigned to 0/4 mA current) Upper range value (value assigned to 20 mA current) With Forward flow option • a (—): The flow components outside the scaled measuring range cannot be taken into account for signal output.
Page 120 Description of device parameters Proline Cubemass 300 Modbus RS485 Damping out. 1 to n  Navigation  Expert → Output → Curr.output 1 to n → Damping out. 1 to n (0363–1 to n) Prerequisite One of the following options is selected in the Assign curr. parameter (→  110): •...
Page 121 Proline Cubemass 300 Modbus RS485 Description of device parameters Response time Navigation  Expert → Output → Curr.output 1 to n → Response time (0378–1 to n) Prerequisite One of the following options is selected in the Assign curr. parameter (→  110): •...
Page 122 Description of device parameters Proline Cubemass 300 Modbus RS485 Failure mode  Navigation  Expert → Output → Curr.output 1 to n → Failure mode (0364–1 to n) Prerequisite One of the following options is selected in the Assign curr. parameter (→  110): •...
Page 123 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description This setting does not affect the failsafe mode of other outputs and totalizers. This is specified in separate parameters. "Min." option The current output adopts the value of the lower level for signal on alarm.
Page 124: Pulse/Frequency/Switch Output
Description of device parameters Proline Cubemass 300 Modbus RS485 Measur. curr. 1 to n Navigation  Expert → Output → Curr.output 1 to n → Measur. curr. 1 to n (0366–1 to n) Description Use this function to display the actual measured value of the output current.
Page 125 Proline Cubemass 300 Modbus RS485 Description of device parameters Response time (0491–1 to n) →  138 Failure mode (0451–1 to n) →  139 Failure freq. (0474–1 to n) →  140 Output freq. 1 to n (0471–1 to n) →...
Page 126 Description of device parameters Proline Cubemass 300 Modbus RS485 Signal mode  Navigation  Expert → Output → PFS output 1 to n → Signal mode (0490–1 to n) Description Use this function to select the signal mode for the pulse/frequency/switch output.
Page 127 Proline Cubemass 300 Modbus RS485 Description of device parameters U[V] B < P A0026883  5 Quantity-proportional pulse (pulse value) with pulse width to be configured Pulse width entered Pauses between the individual pulses "Frequency" option Flow-proportional frequency output with 1:1 on/off ratio...
Page 128 Description of device parameters Proline Cubemass 300 Modbus RS485 U[V] A0026885  8 Alarm, low level Assign pulse 1 to n  Navigation  Expert → Output → PFS output 1 to n → Assign pulse 1 to n (0460–1 to n) Prerequisite The Pulse option is selected in the Operating mode parameter (→...
Page 129 Proline Cubemass 300 Modbus RS485 Description of device parameters Value per pulse  Navigation  Expert → Output → PFS output 1 to n → Value per pulse (0455–1 to n) Prerequisite In the Operating mode parameter (→  126), the Pulse option is selected, and one of the following options is selected in the Assign pulse parameter (→...
Page 130 Description of device parameters Proline Cubemass 300 Modbus RS485 U[V] B < P U[V] B = P A0026882 Pulse width entered Pauses between the individual pulses Example • Pulse value: 0.1 g • Pulse width: 0.1 ms • f : 1 / (2 × 0.1 ms) = 5 kHz •...
Page 131 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Selection • Forward flow Positive flow is output, negative flow is not output. • Forward/Reverse Positive and negative flow are output (absolute value), but a distinction is not made between positive and negative flow.
Page 132 Description of device parameters Proline Cubemass 300 Modbus RS485 Actual value option is only recommended if it can be guaranteed that all possible alarm conditions will not affect the measurement quality. Pulse output 1 to n Navigation  Expert → Output → PFS output 1 to n → Pulse output 1 to n (0456–1 to n) Prerequisite In the Operating mode parameter (→...
Page 133 Proline Cubemass 300 Modbus RS485 Description of device parameters • Target mass flow • Carrier mass fl. • Target vol. flow • Carrier vol. fl. • Targ.corr.vol.fl • Carr.corr.vol.fl • Density • Ref.density • Ref.dens.altern. • GSV flow • GSVa •...
Page 134 Description of device parameters Proline Cubemass 300 Modbus RS485 • Temperature • Carr. pipe temp. • Electronic temp. • Osc. freq. 0 • Freq. fluct. 0 • Osc. ampl. 0 • Osc. damping 0 • Osc.damp.fluct 0 • Signal asymmetry •...
Page 135 Proline Cubemass 300 Modbus RS485 Description of device parameters Val. at min.freq  Navigation  Expert → Output → PFS output 1 to n → Val. at min.freq (0476–1 to n) Prerequisite In the Operating mode parameter (→  126), the Frequency option is selected, and one of the following options is selected in the Assign freq.
Page 136 Description of device parameters Proline Cubemass 300 Modbus RS485 • Concentration • Temperature • Carr. pipe temp. • Electronic temp. • Osc. freq. 0 • Freq. fluct. 0 • Osc. ampl. 0 • Osc. damping 0 • Osc.damp.fluct 0 • Signal asymmetry •...
Page 137 Proline Cubemass 300 Modbus RS485 Description of device parameters • Osc.damp.fluct 0 • Signal asymmetry • Exc. current 0 Detailed description of the options Oscil. frequency, Oscil. amplitude, Oscil. damping and Signal asymmetry: Value 1 display parameter (→  18) Description Use this function to select the measuring mode for the frequency output.
Page 138 Description of device parameters Proline Cubemass 300 Modbus RS485 Description Use this function to enter a time constant for the reaction time of the output signal to fluctuations in the measured value. User entry 0 to 999.9 s Factory setting 0.0 s...
Page 139 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description The response time is made up of the time specified for the following dampings: • Damping of pulse/frequency/switch output →  120 • Depending on the measured variable assigned to the output.
Page 140 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Selection • Actual value In the event of a device alarm, the frequency output continues on the basis of the current flow measurement. The device alarm is ignored. • Defined value In the event of a device alarm, the frequency output continues on the basis of a predefined value.
Page 141 Proline Cubemass 300 Modbus RS485 Description of device parameters Output freq. 1 to n Navigation  Expert → Output → PFS output 1 to n → Output freq. 1 to n (0471–1 to n) Prerequisite In the Operating mode parameter (→  126), the Frequency option is selected.
Page 142 Description of device parameters Proline Cubemass 300 Modbus RS485 Assign diag. beh  Navigation  Expert → Output → PFS output 1 to n → Assign diag. beh (0482–1 to n) Prerequisite • In the Operating mode parameter (→  126), the Switch option is selected.
Page 143 Proline Cubemass 300 Modbus RS485 Description of device parameters • GSVa • NSV flow • NSVa • S&W volume flow • Water cut • Oil density • Water density • Oil mass flow • Water mass flow • Oil volume flow •...
Page 144 Description of device parameters Proline Cubemass 300 Modbus RS485 A0026892 Switch-off value Switch-on value Conductive Non-conductive Process variable Status output Behavior of status output when Switch-on value = Switch-off value: • Process variable > Switch-on value: transistor is conductive • Process variable < Switch-off value: transistor is non-conductive...
Page 145 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description Use this function to enter the limit value for the switch-on value (process variable > switch-on value = closed, conductive). When using a hysteresis: Switch-on value > Switch-off value.
Page 146 Description of device parameters Proline Cubemass 300 Modbus RS485 Factory setting Mass flow Assign status  Navigation  Expert → Output → PFS output 1 to n → Assign status (0485–1 to n) Prerequisite • The Switch option is selected in the Operating mode parameter (→  126).
Page 147 Proline Cubemass 300 Modbus RS485 Description of device parameters Failure mode  Navigation  Expert → Output → PFS output 1 to n → Failure mode (0486–1 to n) Description Use this function to select a failsafe mode for the switch output in the event of a device alarm.
Page 148: Relay Output 1 To N" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Factory setting Additional information Selection No option (passive - negative) A0026693 Yes option (passive - positive) A0026692 3.5.3 "Relay output 1 to n" submenu Navigation  Expert → Output → Relay output 1 to n ‣...
Page 149 Proline Cubemass 300 Modbus RS485 Description of device parameters Switch status →  154 Powerless relay →  154 Terminal no. Navigation  Expert → Output → Relay output 1 to n → Terminal no. (0812–1 to n) Description Displays the terminal numbers used by the relay output module.
Page 150 Description of device parameters Proline Cubemass 300 Modbus RS485 • Limit Indicates if a specified limit value has been reached for the process variable. Is used to output diagnostic information relating to the process and to react to it appropriately at the system level.
Page 151 Proline Cubemass 300 Modbus RS485 Description of device parameters • NSVa • S&W volume flow • Water cut • Oil density • Water density • Oil mass flow • Water mass flow • Oil volume flow • Water vol. flow •...
Page 152 Description of device parameters Proline Cubemass 300 Modbus RS485 Assign status  Navigation  Expert → Output → Relay output 1 to n → Assign status (0805–1 to n) Prerequisite In the Relay outp.func. parameter (→  149), the Digital Output option is selected.
Page 153 Proline Cubemass 300 Modbus RS485 Description of device parameters Switch-on value  Navigation  Expert → Output → Relay output 1 to n → Switch-on value (0810–1 to n) Prerequisite In the Relay outp.func. parameter (→  149), the Limit option is selected.
Page 154 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Selection • Actual status In the event of a device alarm, faults are ignored and the current behavior of the input value is output by the relay output. The Actual status option behaves in the same way as the current input value.
Page 155: Double Pulse Output" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters 3.5.4 "Double pulse output" submenu Navigation  Expert → Output → Double pulse out ‣ Double pulse out Master term. no. (0981) →  155 Slave term. no. (0990) →  155 Signal mode (0991) →...
Page 156 Description of device parameters Proline Cubemass 300 Modbus RS485 User interface • Not used • 24-25 (I/O 2) • 22-23 (I/O 3) Additional information "Not used" option The double pulse output does not use any terminal numbers. Signal mode ...
Page 157 Proline Cubemass 300 Modbus RS485 Description of device parameters Value per pulse  Navigation  Expert → Output → Double pulse out → Value per pulse (0983) Description Use this function to enter the value for the measured value that a pulse is equivalent to.
Page 158 Description of device parameters Proline Cubemass 300 Modbus RS485 Measuring mode  Navigation  Expert → Output → Double pulse out → Measuring mode (0984) Description Use this function to select the measuring mode for the double pulse output. Selection •...
Page 159 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description The dictates of safety render it advisable to ensure that the double pulse output shows a predefined behavior in the event of a device alarm. Selection • Actual value In the event of a device alarm, the double pulse output continues on the basis of the current flow measurement.
Page 160: Communication" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 A0026692 "Communication" submenu Navigation  Expert → Communication ‣ Communication ‣ Modbus config. →  160 ‣ Modbus info →  165 ‣ Modbus data map →  166 ‣ Web server →...
Page 161: Bus Address
Proline Cubemass 300 Modbus RS485 Description of device parameters Bus address  Navigation  Expert → Communication → Modbus config. → Bus address (7112) Description For entering the device address. User entry 1 to 247 Factory setting Baudrate  Navigation ...
Page 162: Byte Order
Changing the byte sequence in the host system often requires a extensive knowledge and significant programming efforts. Endress+Hauser introduced the Byte order parameter (→  162) for this reason. This makes it possible to use the standard settings of the host system and change the byte sequence on the measuring device by trial and error.
Page 163 Proline Cubemass 300 Modbus RS485 Description of device parameters achieved by changing the byte sequence, the settings for the byte sequence of the host system must be adapted accordingly. Byte transmission sequence Byte addressing, i.e. the transmission sequence of the bytes, is not specified in the Modbus specification.
Page 164: Telegram Delay
Description of device parameters Proline Cubemass 300 Modbus RS485 Telegram delay  Navigation  Expert → Communication → Modbus config. → Telegram delay (7146) Description Use this function to enter a delay time after which the measuring device replies to the request telegram of the Modbus master.
Page 165: Modbus Info" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Selection • Off The terminating resistor is disabled. • On The terminating resistor is enabled. For detailed information about enabling the terminating resistor, see the Operating Instructions for the device, "Enabling the terminating resistor" section→  7 Fieldb.writ.acc.
Page 166: Modbus Data Map" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Device ID Navigation  Expert → Communication → Modbus info → Device ID (7153) Description Displays the device ID for identifying the measuring device. User interface 4-digit hexadecimal number Device revision Navigation ...
Page 167: Web Server" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters 3.6.4 "Web server" submenu Navigation  Expert → Communication → Web server ‣ Web server Webserv.language (7221) →  167 MAC Address (7214) →  168 DHCP client (7212) →  168 →...
Page 168 Description of device parameters Proline Cubemass 300 Modbus RS485 MAC Address Navigation  Expert → Communication → Web server → MAC Address (7214) Description Displays the MAC address of the measuring device. User interface Unique 12-digit character string comprising letters and numbers Factory setting Each measuring device is given an individual address.
Page 169 Proline Cubemass 300 Modbus RS485 Description of device parameters Subnet mask  Navigation  Expert → Communication → Web server → Subnet mask (7211) Description Displays the subnet mask. User entry 4 octet: 0 to 255 (in the particular octet) Factory setting 255.255.255.0...
Page 170: Wlan Settings" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Login page  Navigation  Expert → Communication → Web server → Login page (7273) Description Use this function to select the format of the login page. Selection • Without header •...
Page 171 Proline Cubemass 300 Modbus RS485 Description of device parameters Select antenna (2713) →  175 Connection state (2722) →  175 Rec.sig.strength (2721) →  175 WLAN IP address (2711) →  173 Gateway IP addr. (2719) →  176 IP address DNS (2720) →...
Page 172 Description of device parameters Proline Cubemass 300 Modbus RS485 Factory setting – Network security  Navigation  Expert → Communication → WLAN settings → Network security (2705) Description Use this function to select the type of security for the WLAN interface.
Page 173 Proline Cubemass 300 Modbus RS485 Description of device parameters WLAN password  Navigation  Expert → Communication → WLAN settings → WLAN password (2716) Description Use this function to enter the WLAN password. User entry – Factory setting – WLAN IP address ...
Page 174 Description of device parameters Proline Cubemass 300 Modbus RS485 Factory setting 255.255.255.0 WLAN passphrase  Navigation  Expert → Communication → WLAN settings → WLAN passphrase (2706) Prerequisite The WPA2-PSK option is selected in the Security type parameter (→  172).
Page 175 Proline Cubemass 300 Modbus RS485 Description of device parameters WLAN channel  Navigation  Expert → Communication → WLAN settings → WLAN channel (2704) Description Use this function to enter the WLAN channel. User entry 1 to 11 Factory setting...
Page 176: Application" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Factory setting High Gateway IP addr. Navigation  Expert → Communication → WLAN settings → Gateway IP addr. (2719) Description Use this function to enter the IP address of the gateway.
Page 177: Totalizer 1 To N" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Selection • Cancel • Reset + totalize Factory setting Cancel Additional information Selection Options Description Cancel No action is executed and the user exits the parameter. Reset + totalize Resets all totalizers to 0 and restarts the totaling process. This deletes all the flow values previously totalized.
Page 178 Description of device parameters Proline Cubemass 300 Modbus RS485 • Targ.corr.vol.fl • Carr.corr.vol.fl • GSV flow • GSVa • NSV flow • NSVa • S&W volume flow • Oil mass flow • Water mass flow • Oil volume flow • Water vol. flow •...
Page 179 Proline Cubemass 300 Modbus RS485 Description of device parameters SI units US units Imperial units • cm³ • af • gal (imp) • dm³ • ft³ • Mgal (imp) • m³ • fl oz (us) • bbl (imp;oil) • ml •...
Page 180 Description of device parameters Proline Cubemass 300 Modbus RS485 Operation mode  Navigation  Expert → Application → Totalizer 1 to n → Operation mode (0908–1 to n) Prerequisite One of the following options is selected in the Assign variable parameter (→  177) of the Totalizer 1 to n submenu: •...
Page 181 Proline Cubemass 300 Modbus RS485 Description of device parameters Factory setting Totalize Additional information Selection Options Description Totalize The totalizer is started or continues running. Reset + hold The totaling process is stopped and the totalizer is reset to 0.
Page 182: Concentration" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Failure mode  Navigation  Expert → Application → Totalizer 1 to n → Failure mode (0901–1 to n) Prerequisite One of the following options is selected in the Assign variable parameter (→  177) of the Totalizer 1 to n submenu: •...
Page 183: Diagnostics" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Navigation  Expert → Application → Petroleum ‣ Petroleum "Diagnostics" submenu Navigation  Expert → Diagnostics ‣ Diagnostics Actual diagnos. (0691) →  184 Prev.diagnostics (0690) →  184 Time fr. restart (0653) →...
Page 184 Description of device parameters Proline Cubemass 300 Modbus RS485 Actual diagnos. Navigation  Expert → Diagnostics → Actual diagnos. (0691) Prerequisite A diagnostic event has occurred. Description Displays the current diagnostic message. If two or more messages occur simultaneously, the message with the highest priority is shown on the display.
Page 185 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Display Via the local display: the time stamp and corrective measures referring to the cause of the diagnostic message can be accessed via the  key. Example For the display format: F271 Main electronics...
Page 186: Diagnostic List" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information User interface The maximum number of days is 9999, which is equivalent to 27 years. 3.8.1 "Diagnostic list" submenu Navigation  Expert → Diagnostics → Diagnostic list ‣ Diagnostic list Diagnostics 1 (0692) →...
Page 187 Proline Cubemass 300 Modbus RS485 Description of device parameters User interface Days (d), hours (h), minutes (m) and seconds (s) Additional information Display The diagnostic message can be viewed via the Diagnostics 1 parameter (→  186). Example For the display format:...
Page 188 Description of device parameters Proline Cubemass 300 Modbus RS485 Diagnostics 3 Navigation  Expert → Diagnostics → Diagnostic list → Diagnostics 3 (0694) Description Displays the current diagnostics message with the third-highest priority. User interface Symbol for diagnostic behavior, diagnostic code and short message.
Page 189 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Display Via the local display: the time stamp and corrective measures referring to the cause of the diagnostic message can be accessed via the  key. Examples For the display format: •...
Page 190: Event Logbook" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Timestamp Navigation  Expert → Diagnostics → Diagnostic list → Timestamp Description Displays the operating time when the diagnostic message with the fifth-highest priority occurred. User interface Days (d), hours (h), minutes (m) and seconds (s)
Page 191 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description The status signals are categorized in accordance with VDI/VDE 2650 and NAMUR Recommendation NE 107: • F = Failure • C = Function Check • S = Out of Specification •...
Page 192: Device Information" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Event list Navigation  Expert → Diagnostics → Event logbook → Event list Description Displays the history of event messages of the category selected in the Filter options parameter (→  190).
Page 193 A maximum of 11-digit character string comprising letters and numbers. Additional information Description Uses of the serial number • To identify the measuring device quickly, e.g. when contacting Endress+Hauser. • To obtain specific information on the measuring device using the Device Viewer: www.endress.com/deviceviewer Endress+Hauser...
Page 194 The device features are not directly readable from the order code. Uses of the order code • To order an identical spare device. • To identify the device quickly and easily, e.g. when contacting Endress+Hauser. Endress+Hauser...
Page 195 Proline Cubemass 300 Modbus RS485 Description of device parameters Ext. order cd. 1  Navigation  Expert → Diagnostics → Device info → Ext. order cd. 1 (0023) Description Displays the first part of the extended order code. On account of length restrictions, the extended order code is split into a maximum of 3 parameters.
Page 196: Mainboard Module" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Factory setting 2.02.00 Additional information Description This electronic nameplate stores a data record for device identification that includes more data than the nameplates attached to the outside of the device. 3.8.4 "Mainboard module"...
Page 197: Sens. Electronic" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters User interface Positive integer 3.8.5 "Sens. electronic" submenu Navigation  Expert → Diagnostics → Sens. electronic ‣ Sens. electronic Software rev. (0072) →  197 Build no. softw. (0079) →  197 →...
Page 198: I/O Module 1" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 3.8.6 "I/O module 1" submenu Navigation  Expert → Diagnostics → I/O module 1 ‣ I/O module Software rev. (0072) →  198 I/O 1 terminals Navigation  Expert → Diagnostics → I/O module 1 → I/O 1 terminals (3902–1) Description Displays the terminal numbers used by the I/O module.
Page 199 Proline Cubemass 300 Modbus RS485 Description of device parameters I/O 1 terminals Navigation  Expert → Diagnostics → I/O module 1 → I/O 1 terminals (3902–1) Description Displays the terminal numbers used by the I/O module. User interface • Not used •...
Page 200: I/O Module 3" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 3.8.8 "I/O module 3" submenu Navigation  Expert → Diagnostics → I/O module 3 ‣ I/O module 3 I/O 3 terminals →  200 Software rev. →  200 →  200 Build no.
Page 201: Display Module" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Bootloader rev. Navigation  Expert → Diagnostics → I/O module 3 → Bootloader rev. (0073) Description Displays the bootloader revision of the software. User interface Positive integer 3.8.9 "Display module" submenu Navigation ...
Page 202: Data Logging" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 Bootloader rev. Navigation  Expert → Diagnostics → Display module → Bootloader rev. (0073) Description Displays the bootloader revision of the software. User interface Positive integer 3.8.10 "Data logging" submenu Navigation ...
Page 203 Proline Cubemass 300 Modbus RS485 Description of device parameters Assign chan. 1  Navigation  Expert → Diagnostics → Data logging → Assign chan. 1 (0851) Prerequisite The Extended HistoROM application package is available. The software options currently enabled are displayed in the SW option overv.
Page 204 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description A total of 1000 measured values can be logged. This means: • 1000 data points if 1 logging channel is used • 500 data points if 2 logging channels are used •...
Page 205 Proline Cubemass 300 Modbus RS485 Description of device parameters Assign chan. 4  Navigation  Expert → Diagnostics → Data logging → Assign chan. 4 (0854) Prerequisite The Extended HistoROM application package is available. The software options currently enabled are displayed in the SW option overv.
Page 206 Description of device parameters Proline Cubemass 300 Modbus RS485 Clear logging  Navigation  Expert → Diagnostics → Data logging → Clear logging (0855) Prerequisite The Extended HistoROM application package is available. The software options currently enabled are displayed in the SW option overv.
Page 207 Proline Cubemass 300 Modbus RS485 Description of device parameters Factory setting Additional information Description Once measured value logging has been started with the Data log.control parameter (→  207), the device does not save any data for the duration of the time delay entered.
Page 208 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Selection • Done Measured value logging has been performed and completed successfully. • Delay active Measured value logging has been started but the logging interval has not yet elapsed.
Page 209 Proline Cubemass 300 Modbus RS485 Description of device parameters • Carrier mass fl. • Density • Ref.density • Concentration • Carr. pipe temp. • Electronic temp. • Curr.output 1 • Osc. freq. 0 • Freq. fluct. 0 • Oscil. amplitude •...
Page 210 Description of device parameters Proline Cubemass 300 Modbus RS485 Description See the Display channel 1 parameter →  208 "Displ.channel 3" submenu Navigation  Expert → Diagnostics → Data logging → Displ.channel 3 ▸ Displ.channel 3 Display channel 3 →  210...
Page 211: Min/Max Val." Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters 3.8.11 "Min/max val." submenu Navigation  Expert → Diagnostics → Min/max val. ‣ Min/max val. Reset min/max (6151) →  211 ‣ Electronic temp. →  212 ‣ Medium temp. →  213 ‣...
Page 212 Description of device parameters Proline Cubemass 300 Modbus RS485 "Electronic temp." submenu Navigation  Expert → Diagnostics → Min/max val. → Electronic temp. ‣ Electronic temp. Minimum value →  212 Maximum value →  212 Maximum value Navigation  Expert → Diagnostics → Min/max val. → Electronic temp. → Maximum value (6051)
Page 213 Proline Cubemass 300 Modbus RS485 Description of device parameters "Medium temp." submenu Navigation  Expert → Diagnostics → Min/max val. → Medium temp. ‣ Medium temp. Minimum value (6109) →  213 Maximum value (6108) →  213 Minimum value Navigation ...
Page 214 Description of device parameters Proline Cubemass 300 Modbus RS485 Minimum value Navigation  Expert → Diagnostics → Min/max val. → Carr. pipe temp. → Minimum value (6030) Prerequisite For the following order code "Application package", option EB "Heartbeat Verification + Monitoring"...
Page 215 Proline Cubemass 300 Modbus RS485 Description of device parameters Minimum value Navigation  Expert → Diagnostics → Min/max val. → Oscil. frequency → Minimum value (6071) Description Displays the lowest previously measured oscillation frequency. User interface Signed floating-point number Maximum value Navigation ...
Page 216 Description of device parameters Proline Cubemass 300 Modbus RS485 User interface Signed floating-point number "Oscil. damping" submenu Navigation  Expert → Diagnostics → Min/max val. → Oscil. damping ‣ Oscil. damping Minimum value (6122) →  216 →  216...
Page 217: Heartbeat" Submenu
Proline Cubemass 300 Modbus RS485 Description of device parameters Minimum value Navigation  Expert → Diagnostics → Min/max val. → Signal asymmetry → Minimum value (6015) Description Displays the lowest previously measured signal asymmetry. User interface Signed floating-point number Maximum value Navigation ...
Page 218: Simulation" Submenu
Description of device parameters Proline Cubemass 300 Modbus RS485 3.8.13 "Simulation" submenu Navigation  Expert → Diagnostics → Simulation ‣ Simulation Assign proc.var. (1810) →  219 Proc. var. value (1811) →  220 →  220 Status inp. sim. (1355) Signal level (1356) →...
Page 219 Proline Cubemass 300 Modbus RS485 Description of device parameters Assign proc.var.  Navigation  Expert → Diagnostics → Simulation → Assign proc.var. (1810) Description Use this function to select a process variable for the simulation process that is activated. The display alternates between the measured value and a diagnostic message of the "Function check"...
Page 220 Description of device parameters Proline Cubemass 300 Modbus RS485 Proc. var. value  Navigation  Expert → Diagnostics → Simulation → Proc. var. value (1811) Description Use this function to enter a simulation value for the selected process variable. Subsequent measured value processing and the signal output use this simulation value.
Page 221 Proline Cubemass 300 Modbus RS485 Description of device parameters Description Use this function to select the signal level for the simulation of the status input. In this way, users can verify the correct configuration of the status input and the correct function of upstream feed-in units.
Page 222 Description of device parameters Proline Cubemass 300 Modbus RS485 Curr.out. 1 to n sim.  Navigation  Expert → Diagnostics → Simulation → Curr.out. 1 to n sim. (0354–1 to n) Description Use this function to switch simulation of the current output on and off. The display alternates between the measured value and a diagnostic message of the "Function check"...
Page 223 Proline Cubemass 300 Modbus RS485 Description of device parameters Description Use this function to switch simulation of the frequency output on and off. The display alternates between the measured value and a diagnostic message of the "Function check" category (C) while simulation is in progress.
Page 224 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description The desired simulation value is defined in the Pulse value 1 to n parameter. Selection • Off Pulse simulation is switched off. The device is in normal measuring mode or another process variable is being simulated.
Page 225 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description The desired simulation value is defined in the Switch status 1 to n parameter. Selection • Off Switch simulation is switched off. The device is in normal measuring mode or another process variable is being simulated.
Page 226 Description of device parameters Proline Cubemass 300 Modbus RS485 Additional information Description The desired simulation value is defined in the Switch status 1 to n parameter. Selection • Off Relay simulation is switched off. The device is in normal measuring mode or another process variable is being simulated.
Page 227 Proline Cubemass 300 Modbus RS485 Description of device parameters Additional information Description The desired simulation value is defined in the Pulse value parameter (→  227). Selection • Off Simulation of the double pulse output is switched off. The device is in normal measuring mode or another process variable is being simulated.
Page 228 Description of device parameters Proline Cubemass 300 Modbus RS485 Event category  Navigation  Expert → Diagnostics → Simulation → Event category (0738) Description Use this function to select the category of the diagnostic events that are displayed for the simulation in the Diag.
Page 229: Country-Specific Factory Settings
Proline Cubemass 300 Modbus RS485 Country-specific factory settings Country-specific factory settings SI units Not valid for USA and Canada. 4.1.1 System units Mass Mass flow kg/h Volume Volume flow Corrected volume Corrected volume flow Nl/h Density kg/l Reference density kg/Nl Temperature °C...
Page 230: On Value Low Flow Cut Off
Country-specific factory settings Proline Cubemass 300 Modbus RS485 Nominal diameter [mm] [kg/p] 0.01 4.1.5 On value low flow cut off The switch-on point depends on the type of medium and the nominal diameter. Nominal diameter On-value for liquid [mm] [kg/h] 0.08...
Page 231: Output Current Span
Proline Cubemass 300 Modbus RS485 Country-specific factory settings Nominal diameter [in] [lb/min] ¹/₂₄ 0.15 ¹/₁₂ 0.75 ¹/₈ ¹/₄ 4.2.3 Output current span Current output 1 to n 4 to 20 mA US 4.2.4 Pulse value For detailed information about the pulse value for measuring devices for custody transfer, see the Special Documentation for the device →...
Page 232: Explanation Of Abbreviated Units
Explanation of abbreviated units Proline Cubemass 300 Modbus RS485 Explanation of abbreviated units SI units Process variable Units Explanation Density g/cm³, g/m³ Gram/volume unit kg/dm³, kg/l, kg/m³ Kilogram/volume unit SD4°C, SD15°C, SD20°C Specific density: The specific density is the ratio of the density of the fluid to the density of water at a water temperature of 4 °C (39 °F), 15 °C (59 °F), 20 °C (68 °F).
Page 233 Proline Cubemass 300 Modbus RS485 Explanation of abbreviated units Process variable Units Explanation Pressure psi a Pounds per square inch (absolute) psi g Pounds per square inch (gauge) Mass oz, lb, STon Ounce, pound, standard ton Mass flow oz/s, oz/min, oz/h, oz/d...
Page 234: Imperial Units
Explanation of abbreviated units Proline Cubemass 300 Modbus RS485 Imperial units Process variable Units Explanation Density lb/gal (imp), lb/bbl (imp;beer), Pound/volume unit lb/bbl (imp;oil) Corrected Sgal (imp) Standard gallon volume Correct.vol.flow Sgal/s (imp), Sgal/min (imp), Standard gallon/time unit Sgal/h (imp), Sgal/d (imp)
Page 235: Modbus Rs485 Register
Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Modbus RS485 Register Information Notes 6.1.1 Structure of the register information The individual parts of a parameter description are described in the following section: Navigation: navigation path to the parameter Parameter...
Page 236: Overview Of The Expert Operating Menu
Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Function code Access type Register in accordance with "Modbus Register in accordance with Applications Protocol Specification" "Modicon Modbus Protocol Reference Guide" Read XXXX 3XXXX Example: mass flow = 2007 Example: mass flow = 32007...
Page 237 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Decimal places 3 (0118) →  251 Value 4 display (0109) →  251 Decimal places 4 (0119) →  252 Display interval (0096) →  252 Display damping (0094) →  252 Header (0097) →...
Page 238 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 ‣ Sensor →  255 ‣ Measured val. →  255 ‣ Process variab. →  255 ‣ Totalizer →  255 ‣ →  256 Input values ‣ Output values →...
Page 239 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information ‣ Low flow cut off →  261 ‣ Partial pipe det →  262 ‣ Measurement mode →  262 Select medium (6062) →  262 Select gas type (6074) →...
Page 240 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 ‣ I/O config. →  264 I/O 1 to n terminals (3902–1 to n) →  264 I/O 1 to n info (3906–1 to n) →  264 I/O 1 to n type (3901–1 to n) →...
Page 241 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Assign curr. 1 to n (0359–1 to n) →  266 Current span (0353–1 to n) →  266 Fixed current (0365–1 to n) →  266 0/4 mA value (0367–1 to n) →...
Page 242 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Val. at min.freq (0476–1 to n) →  269 Val. at max.freq (0475–1 to n) →  269 Measuring mode (0479–1 to n) →  269 Damping out. 1 to n (0477–1 to n) →...
Page 243 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Assign diag. beh (0806–1 to n) →  272 Assign status (0805–1 to n) →  272 Switch-off value (0809–1 to n) →  272 Switch-off delay (0813–1 to n) →  272 Switch-on value (0810–1 to n)
Page 244 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Data trans. mode (7115) →  274 Parity (7122) →  274 Byte order (7113) →  274 Telegram delay (7146) →  274 →  274 Failure mode (7116) Bus termination (7155) →...
Page 245 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Security type (2705) →  276 WLAN passphrase (2706) →  276 Assign SSID name (2708) →  276 SSID name (2707) →  276 Select antenna (2713) →  276 WLAN channel (2704) →...
Page 246 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Diagnostics 4 (0695) →  278 Diagnostics 5 (0696) →  278 ‣ Event logbook →  279 Filter options (0705) →  279 ‣ →  279 Device info Device tag (0011) →...
Page 247 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information ‣ I/O module 3 →  280 I/O 3 terminals (3902–3) →  280 Software rev. (0072) →  280 ‣ Display module →  280 Software rev. (0072) →  280 ‣...
Page 248 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Data log. status (0858) →  283 Logging duration (0861) →  283 ‣ Simulation →  283 Assign proc.var. (1810) →  283 →  283 Proc. var. value (1811) Status inp.
Page 249: Register Information
Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Register information Navigation: Expert Parameter Register Data type Access Selection / User entry / User interface →  Direct access (0106) 3878 Integer Read / Write 0 to 65 535 Locking status (0004) 4918 Integer Read 256 = Hardware locked 512 = Temp.
Page 250 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → System → Display Parameter Register Data type Access Selection / User entry / User interface →  Value 1 display (0107) 3963 Integer Read / Write 1 = Mass flow 2 = Volume flow 3 = Correct.vol.flow...
Page 251 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Navigation: Expert → System → Display Parameter Register Data type Access Selection / User entry / User interface →  Value 2 display (0108) 3964 Integer Read / Write 1 = Mass flow 2 = Volume flow 3 = Correct.vol.flow...
Page 252 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → System → Display Parameter Register Data type Access Selection / User entry / User interface →  Decimal places 4 (0119) 4051 Integer Read / Write 0 = x 1 = x.x 2 = x.xx 3 = x.xxx...
Page 253 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information "Diagn. behavior" submenu Navigation: Expert → System → Diagn. handling → Diagn. behavior Parameter Register Data type Access Selection / User entry / User interface →  Diagnostic no. 046 (0709) 2756 Integer Read / Write 0 = Off...
Page 254 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → System → Diagn. handling → Diagn. behavior Parameter Register Data type Access Selection / User entry / User interface →  Diagnostic no. 835 (0702) 2760 Integer Read / Write 0 = Off 1 = Logbook only...
Page 255: Sensor" Submenu
Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information "Def. access code" wizard Navigation: Expert → System → Administration → Def. access code Parameter Register Data type Access Selection / User entry / User interface →  Def. access code 8677 to 8684 String Read / Write...
Page 256 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 "Input values" submenu "Current input 1 to n" submenu Navigation: Expert → Sensor → Measured val. → Input values → Current input 1 to n Parameter Register Data type Access Selection / User entry / User interface →...
Page 257 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information "Relay output 1 to n" submenu Navigation: Expert → Sensor → Measured val. → Output values → Relay output 1 to n Parameter Register Data type Access Selection / User entry / User interface → ...
Page 258 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → Sensor → System units Parameter Register Data type Access Selection / User entry / User interface →  Volume flow unit (0553) 2103 Integer Read / Write 0 = cm³/s 1 = cm³/min 2 = cm³/h 3 = cm³/d...
Page 259 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Navigation: Expert → Sensor → System units Parameter Register Data type Access Selection / User entry / User interface →  71 = gal/d (imp) 72 = Mgal/s (imp) 73 = Mgal/min (imp) 74 = Mgal/h (imp) 75 = Mgal/d (imp) 76 = bbl/s (imp;beer)
Page 260 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → Sensor → System units Parameter Register Data type Access Selection / User entry / User interface →  Corr. vol. unit (0575) 2106 Integer Read / Write 100 = Nl 101 = Nm³ 102 = Sm³...
Page 261 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information "User-spec. units" submenu Navigation: Expert → Sensor → System units → User-spec. units Parameter Register Data type Access Selection / User entry / User interface →  Mass text (0560) String Read / Write Max. 10 characters such as letters,...
Page 262 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 "Partial pipe det" submenu Navigation: Expert → Sensor → Process param. → Partial pipe det Parameter Register Data type Access Selection / User entry / User interface →  Assign variable (1860) 5106 Integer Read / Write...
Page 263 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Navigation: Expert → Sensor → External comp. Parameter Register Data type Access Selection / User entry / User interface →  Temperature mode (6184) 5515 Integer Read / Write 0 = Internal value 1 = External value...
Page 264: I/O Config." Submenu
Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → Sensor → Sensor adjustm. → Variable adjust Parameter Register Data type Access Selection / User entry / User interface →  Vol. flow offset (1841) 5525 to 5526 Float Read / Write Signed floating-point number Vol.
Page 265: Input" Submenu
Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information 6.3.4 "Input" submenu "Current input 1 to n" submenu Navigation: Expert → Input → Current input 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Terminal no. (1611–1 to n)
Page 266: Output" Submenu
Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 6.3.5 "Output" submenu "Curr.output 1 to n" submenu Navigation: Expert → Output → Curr.output 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Terminal no. (0379–1 to n)
Page 267 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Navigation: Expert → Output → Curr.output 1 to n Parameter Register Data type Access Selection / User entry / User interface →  20 mA value (0372–1 to n) 1: 5915 to 5916 Float Read / Write...
Page 268 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → Output → PFS output 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Assign pulse 1 to n (0460–1 to n) 1: 2461 Integer Read / Write...
Page 269 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Navigation: Expert → Output → PFS output 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Assign freq. (0478–1 to n) 1: 2614 Integer Read / Write 0 = Off...
Page 270 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → Output → PFS output 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Failure mode (0451–1 to n) 1: 2367 Integer Read / Write 0 = Actual value...
Page 271 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Navigation: Expert → Output → PFS output 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Assign status (0485–1 to n) 1: 3374 Integer Read / Write 0 = Low flow cut off...
Page 272 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → Output → Relay output 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Assign limit (0807–1 to n) 1: 8248 Integer Read / Write 1 = Mass flow...
Page 273 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Navigation: Expert → Output → Relay output 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Switch status (0801–1 to n) 1: 3518 Integer Read 1 = Open...
Page 274: Communication" Submenu
Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → Output → Double pulse out Parameter Register Data type Access Selection / User entry / User interface →  Pulse output (0987) 7041 to 7042 Float Read Positive floating-point number Invert outp.sig. (0993)
Page 275 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information "Modbus data map" submenu Navigation: Expert → Communication → Modbus data map Parameter Register Data type Access Selection / User entry / User interface →  Scan list reg.0 to 15 (7114) 0: 5001 Integer Read / Write...
Page 276: Application" Submenu
Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 "WLAN settings" submenu Navigation: Expert → Communication → WLAN settings Parameter Register Data type Access Selection / User entry / User interface →  WLAN (2702) 6178 Integer Read / Write 0 = Disable 1 = Enable WLAN IP address (2711) 8643 to 8649.5...
Page 277 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information "Totalizer 1 to n" submenu Navigation: Expert → Application → Totalizer 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Assign variable (0914–1 to n) 1: 2601 Integer Read / Write...
Page 278: Diagnostics" Submenu
Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → Application → Totalizer 1 to n Parameter Register Data type Access Selection / User entry / User interface →  Control Tot. 1 to n (0912–1 to n) 1: 2608 Integer Read / Write...
Page 279 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information "Event logbook" submenu Navigation: Expert → Diagnostics → Event logbook Parameter Register Data type Access Selection / User entry / User interface →  Filter options (0705) 4596 Integer Read / Write 0 = Failure (F) 4 = Mainten. req.(M) 8 = Funct.
Page 280 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 "I/O module 2" submenu Navigation: Expert → Diagnostics → I/O module 2 Parameter Register Data type Access Selection / User entry / User interface →  I/O 2 terminals (3902–2) 6542 Integer Read 0 = Not used...
Page 281 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information "Carr. pipe temp." submenu Navigation: Expert → Diagnostics → Min/max val. → Carr. pipe temp. Parameter Register Data type Access Selection / User entry / User interface →  Minimum value (6030) 7533 to 7534...
Page 282 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 "Data logging" submenu Navigation: Expert → Diagnostics → Data logging Parameter Register Data type Access Selection / User entry / User interface →  Assign chan. 1 (0851) 2445 Integer Read / Write 0 = Off 1 = Mass flow 2 = Volume flow 3 = Correct.vol.flow...
Page 283 Proline Cubemass 300 Modbus RS485 Modbus RS485 Register Information Navigation: Expert → Diagnostics → Data logging Parameter Register Data type Access Selection / User entry / User interface →  Data log. status (0858) 5937 Integer Read 0 = Done 1 = Stopped 2 = Active...
Page 284 Modbus RS485 Register Information Proline Cubemass 300 Modbus RS485 Navigation: Expert → Diagnostics → Simulation Parameter Register Data type Access Selection / User entry / User interface →  Value curr.out 1 to n (0355–1 to n) 1: 5995 to 5996 Float Read / Write 3.59 to 22.5 mA...
Page 285: Index
Proline Cubemass 300 Modbus RS485 Index Index 0 … 9 0/4 mA value (Parameter) ....105, 112 Backlight (Parameter) ......28 0% bargraph value 1 (Parameter) .
Page 286 Index Proline Cubemass 300 Modbus RS485 Default gateway (Parameter) ....169 Assign behavior of diagnostic no. 832 (0681) ..38 Define access code (Parameter) .
Page 287 Proline Cubemass 300 Modbus RS485 Index C0 to 5 (6022) ......101 Enter access code (0003) ....13 Calibration factor (6025) .
Page 288 Index Proline Cubemass 300 Modbus RS485 Last backup (2757) ..... . . 29 Operating mode Linear expansion coefficient (1817) ... 92 Pulse/frequency/switch output 1 to n (0469–...
Page 289 Proline Cubemass 300 Modbus RS485 Index Signal mode Current output 1 to n (0379–1 to n) ..109 Current input 1 to n (1610–1 to n) ..104 Pulse/frequency/switch output 1 to n (0492–...
Page 290 Index Proline Cubemass 300 Modbus RS485 WLAN subnet mask (2709) ....173 Function Zero point (6195) ......100 see Parameter Zero point adjustment control (6196) .
Page 291 Proline Cubemass 300 Modbus RS485 Index Measuring value at maximum frequency (Parameter) Pulse/frequency/switch output 1 to n (Submenu) 56, ........135 Measuring value at minimum frequency (Parameter) .
Page 292 Index Proline Cubemass 300 Modbus RS485 Diagnostic handling ..... . . 31 Subnet mask (Parameter) ....169 Diagnostic list .
Page 293 Proline Cubemass 300 Modbus RS485 Index User volume text (Parameter) ....69 User-specific units (Submenu) ....68 Value 1 display (Parameter) .
Page 294 www.addresses.endress.com...

Endress+Hauser Proline Cubemass 300 Description Of Device Parameters

Table of Contents

1 About this Document

2 Overview of the Expert Operating

Menu

3 Description of Device Parameters

Table of Contents

3.6 "Communication" Submenu

4 Country-Specific Factory Settings

5 Explanation of Abbreviated Units

Information

6 Modbus RS485 Register

Index

Quick Links

Chapters

Related Manuals for Endress+Hauser Proline Cubemass 300

Summary of Contents for Endress+Hauser Proline Cubemass 300

Table of Contents