Genie S-65 XC CE Operator's Manual Supplement
4m platform
Hide thumbs
Also See for S-65 XC CE:
- Service and repair manual (169 pages) ,
- Maintenance manual (182 pages) ,
- Operator's manual (68 pages)
Related Manuals for Genie S-65 XC CE
Summary of Contents for Genie S-65 XC CE
- Page 1 Operator's Manual Supplement 4m Platform -65 XC ® ™ CE Models Original Instructions First Edition Third Printing Part No. 1295772GT...
- Page 2 E-mail: awp.techpub@terex.com Copyright © 2020 by Terex Corporation First Edition: Third Printing, January 2020 Genie and "S" are registered trademarks of Terex South Dakota, Inc. in the U.S.A. and many other countries. "XC" is a trademark of Terex South Dakota, Inc.
-
Page 3: Symbol And Hazard Pictorials Definitions
When the 4m platform assembly is attached, this Note: These installation instructions only apply to manual should be considered a permanent part of the Genie model listed on the front cover. your machine and should remain with the machine DANGER Using the 4m Platform with the at all times. -
Page 4: Pre-Operation Inspection
Operator's Manual Supplement First Edition • Third Printing S-65 XC with 4m Platform Pre-operation Inspection Verify the operator’s manual and any necessary supplements are complete, legible and in the storage container located in the platform. Verify all decals are legible and in place. Check the 4m Platform for damage, improperly installed or missing parts and unauthorized modifications. - Page 5 First Edition • Third Printing Operator's Manual Supplement S-65 XC with 4m Platform Decal Inspection Use the inspection to verify that all decals are legible and in place. Decals may vary depending on machine configuration. Part No. Decal Description 1290025* Decal, Warning, Crush Hazard 1290026* Decal, Lock Transport...
- Page 6 Operator's Manual Supplement First Edition • Third Printing S-65 XC with 4m Platform Platform Capacity Range Tilt Sensor Activation Settings Range of motion is controlled automatically based Model Tilt/Slope (front Maximum Boom Angle/ on platform load. to back) Platform Load 272 kg S-65 XC with 4m Platform, Range of Motion S-65 XC...
- Page 7 Transporting a machine with a 4M Platform on a width) standard width trailer requires the turntable to be Continuous improvement of our products is a Genie rotated 3.5 degrees. Lock the rotated turntable policy. Product specifications are subject to change using the Off-center Transport Lock (p/n without notice or obligation.
-
Page 8: Installation Instructions
Repair any machine damage or malfunction USB flash drive before operating the machine. Contents of Kit 1295770GT Before Starting Installation: Description Genie part number Qty. Read, understand and obey the safety rules (1) Assembly, 4m Platform 1295776GT and operating instructions in the appropriate... - Page 9 First Edition • Third Printing Operator's Manual Supplement Installation Instructions Note: Perform this procedure on a firm, level Remove the platform control box mounting surface with the machine in the stowed position fasteners. Lower the control box and set it unless otherwise instructed.
-
Page 10: Software Update
Operator's Manual Supplement First Edition • Third Printing Software Update Software Update Bootloader Firmware Checking the Application and Bootloader Revisions from the Result: Revision "F" or higher, the Bootloader Firmware does not need to be updated. Continue Ground Controls. to Selecting the Platform Option. Verifying the machine application and Result: Revision "E"... - Page 11 First Edition • Third Printing Operator's Manual Supplement Software Update Updating the Machine Software. Selecting the Platform Option. Note: Access to the internet is required to The appropriate platform option must be perform this procedure. selected when installing or removing the 4m platform.
- Page 12 Operator's Manual Supplement First Edition • Third Printing Software Update Press Escape / Escape / Escape. Push in the red Emergency Stop button to the off position. Perform a zero load platform calibration. Refer to Repair Procedure, How to Perform a Zero Load Platform Calibration in the Service and Repair manual that is appropriate for your machine.
- Page 13 First Edition • Third Printing Operator's Manual Supplement Software Update This page intentionally left blank. 4m Platform Part No. 1295772GT Operator's Manual Supplement First Edition • Third Printing Part No. 1295772GT 4m Platform...