Related Manuals for Genie CE Series
Summary of Contents for Genie CE Series
- Page 1 Operator's Manual Supplement 4m Platform -45 XC ® ™ -45 XC TraX ® ™ ™ -65 XC ® ™ -65 XC TraX ® ™ ™ CE Models Original Instructions First Edition Fifth Printing Part No. 1295772GT...
- Page 2 Copyright © 2020 by Terex Corporation First Edition: Fifth Printing, May 2021 Genie and "S" are registered trademarks of Terex South Dakota, Inc. in the U.S.A. and many other countries. "XC" and "TraX" are trademarks of Terex South Dakota, Inc.
-
Page 3: Failure To Obey The Instructions And Safety Rules In This Manual Will Result In Death Or Serious Injury
Note: These installation instructions only apply to When the 4m platform assembly is attached, this the Genie models listed on the front cover. manual should be considered a permanent part of your machine and should remain with the machine Using the 4m Platform with the at all times. -
Page 4: Pre-Operation Inspection
First Edition • Fifth Printing Operator's Manual Supplement S-45 XC, S-45 XC Trax, S-65 XC, S-65 XC Trax with 4m Platform Pre-operation Inspection Verify the operator’s manual and any necessary supplements are complete, legible and in the storage container located in the platform. - Page 5 First Edition • Fifth Printing Operator's Manual Supplement S-45 XC, S-45 XC Trax, S-65 XC, S-65 XC Trax with 4m Platform Decal Inspection - S-45 XC, S-45 XC Trax Use the inspection to verify that all decals are legible and in place. Decals may vary depending on machine configuration.
- Page 6 First Edition • Fifth Printing Operator's Manual Supplement S-45 XC, S-45 XC Trax, S-65 XC, S-65 XC Trax with 4m Platform Decal Inspection - S-65 XC, S-65 XC Trax Use the inspection to verify that all decals are legible and in place. Decals may vary depending on machine configuration.
- Page 7 First Edition • Fifth Printing Operator's Manual Supplement S-45 XC, S-45 XC Trax, S-65 XC, S-65 XC Trax with 4m Platform Platform Capacity Range Tilt Sensor Activation Settings Range of motion is controlled automatically based Model Tilt/Slope (front Maximum Boom Angle/ on platform load.
- Page 8 Platform dimensions, 4m (length x 400 cm x 91 cm width) Securing the Platform – S-65 XC, Continuous improvement of our products is a Genie policy. Product specifications are subject to change S-65 XC Trax with 4m Platform without notice or obligation.
-
Page 9: Installation Instructions
First Edition • Fifth Printing Operator's Manual Supplement Installation Instructions Installation Instructions Tools required: Assorted SAE wrenches Assorted SAE sockets Ratchet Service and Repair Manual Observe and Obey: Tools for software update This procedure shall be completed by a (if required): person authorized to install the 4m Platform. - Page 10 First Edition • Fifth Printing Operator's Manual Supplement Installation Instructions Note: Perform this procedure on a firm, level Remove the platform control box mounting surface with the machine in the stowed position fasteners. Lower the control box and set it unless otherwise instructed.
-
Page 11: Software Update
First Edition • Fifth Printing Operator's Manual Supplement Software Update Software Update Bootloader Firmware Checking the Application and Bootloader Revisions from the Result: The Bootloader Firmware does not need to be updated. Continue to Selecting the Ground Controls. Platform Option - Revision "F" or higher. Verifying the machine application and Result: The Bootloader Firmware must be bootloader firmware revision levels must... - Page 12 First Edition • Fifth Printing Operator's Manual Supplement Software Update Updating the Machine Software Note: Access to the internet is required to perform this procedure. Click on the Hyperlink below or open an internet browser and copy and paste or type the link into the address bar and press enter.
- Page 13 First Edition • Fifth Printing Operator's Manual Supplement Software Update Selecting the Platform Option. Press Escape / Escape / Escape. Push in the red Emergency Stop button to the The appropriate platform option must be off position. selected when installing or removing the 4m platform.
- Page 14 First Edition • Fifth Printing Operator's Manual Supplement Software Update This page intentionally left blank. 4m Platform Part No. 1295772GT Operator's Manual Supplement First Edition • Fifth Printing 4m Platform Part No. 1295772GT...