Table of Contents
Advertisement
H9924RD_EN_0316 3/17/05 10:11 AM Page 6
Setting Up your DVD/ VCR
Basic Connections
• Please refer to the instruction books of your TV,VCR, Stereo
System or other devices as necessary to make the best
connections.
• Make one of the following connections, depending on the
capabilities of your existing equipment.
The following guidelines are options for the best picture and
sound quality available on your DVD/VCR.
Picture
1 Use SCART RGB Output (DVD/VCR(AV1 TV)) for best
picture quality (for DVD and VCR features).
2 Use S-VIDEO Output for the better picture quality (for DVD
features only).
3 If your TV only has a RF-style (Antenna IN or 75 ohm) input,
use the RF OUT for connection and set your TV to channel
22 ~ 69 with the same channel for DVD/VCR is set (for DVD
and VCR features).
Sound
1 Digital audio connections provide the clearest sound. Connect
the DVD/VCR DIGITAL AUDIO OUT (either COAXIAL or
OPTICAL) to your amplifier or receiver (for DVD features only).
2 Use SCART Output (DVD/VCR(AV1 TV)) for better sound
quality (for DVD and VCR features).
If digital connections are not possible, connect the DVD/VCR
ANALOG AUDIO OUT(Left and Right) to your amplifier,
receiver, stereo or TV (for DVD features only).
Warning!
– Never make or change connections with the power
switched on.
– Connect the DVD/VCR directly to your TV, instead of eg.
a VCR, to avoid distortion because DVD video discs are
copy protected.
– Do not connect the ANALOG AUDIO OUT of DVD/VCR
to PHONO IN of your amplifier or receiver.
– If you use the Euro audio/video cable, it is not necessary
to connect the analog audio cable.
Connecting to a TV
1 Connect the antenna or cable to the AERIAL of your DVD/
VCR.
2 Connect the DVD/VCR (AV1 TV) on the DVD/VCR to the
corresponding connector on the TV.
Note:
– Ensure that the "TV" indication on SCART cable is
connected to the TV set and "DVD" indication on SCART
cable is connected to the DVD/VCR.
If your TV has RCA jack, connect the DVD/VCR (AV1 TV)
on the DVD/VCR with RCA Connector Plug to RCA jack on
your TV.
If your TV is not equipped with a SCART input, you can select
the following connection:
If your TV has a S-Video input connector,
1 Connect the antenna or cable to the AERIAL of your DVD/VCR.
2 Connect the S-VIDEO OUT on the DVD/VCR to the S-Video
in on the TV.
3 Connect the ANALOG AUDIO OUT on the DVD/VCR to the
Left and Right audio in on the TV.
(Yellow)(White)
(Red)
RCA JACK
RCA JACK
RCA cable
OR
(Yellow)(White)
(Red)
DVD
DIGITAL
ANALOG
S-VIDEO
AUDIO OUT
AUDIOOUT
OUT
VCR
L
DVD/VCR
OPTICAL
COAXIAL
R
Note:
– You will still need the SCART cable or RF Coaxial cable
for VCR features.
6
TV
OR
Scart Cable
RCA Connector
Plug (supplied)
AERIAL
AV2(DECODER)
AV1(TV)
RF OUT
Simplest connection using only supplied
black RF Coaxial cable
1 Disconnect the antenna or cable from your TV.
2 Connect the antenna or cable to the AERIAL of your DVD/VCR.
3 Connect black RF Coaxial cable to the RF OUT on the rear
panel of the DVD/VCR and to the ANTENNA IN on the TV.
4 Plug in the power cords of the TV and DVD/VCR.
Back of DVD/VCR
Antenna
Indoor/Outdoor
(300 ohm)
AUDIO OUT
OPTICAL
OR
Cable
(75 ohm)
Connecting to an Audio System
(for DVD features)
1 You can also listen to the sound of audio CDs and DVD video
discs by connecting to an optional stereo system.
2 Connect DVD/VCR ANALOG AUDIO OUT (Left and Right)
to the audio in on the stereo system.
STEREO
AUDIO (LEFT) IN
AUDIO (RIGHT) IN
DVD
DIGITAL
ANALOG
S-VIDEO
AUDIO OUT
AUDIOOUT
OUT
VCR
AV2(DECODER)
L
DVD/VCR
AV1(TV)
OPTICAL
COAXIAL
R
Connecting to Optional Equipment
(for DVD features)
• A digital component with a built-in MPEG 2 or Dolby Digital
decoder allows you to enjoy the surround sound while
producing the effect of being in a movie theater or a concert
hall.
• The player outputs the surround sound signals from the
COAXIAL or OPTICAL DIGITAL AUDIO OUT.
If your receiver has a MPEG 2 or Dolby Digital decoder,
Connect the COAXIAL or OPTICAL DIGITAL AUDIO OUT
of the DVD/VCR to the COAXIAL or OPTICAL DIGITAL
AUDIO IN on your receiver.
Notes:
– If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
– You will still need the video cable or RF Coaxial cable
for VCR features.
OPTICAL DIGITAL
AUDIO IN
COAXIAL DIGITAL
AUDIO IN
DVD
DIGITAL
ANALOG
S-VIDEO
AUDIO OUT
AUDIOOUT
OUT
VCR
AV2(DECODER)
L
DVD/VCR
AV1(TV)
OPTICAL
COAXIAL
R
Antenna In
(on back of TV)
example only
DVD
DIGITAL
ANALOG
S-VIDEO
AERIAL
AUDIOOUT
OUT
VCR
AV2(DECODER)
L
COAXIAL
DVD/VCR
AV1(TV)
RF OUT
R
AERIAL
L/MONO
1
AUDIO
R
VIDEO
in
RF OUT
75
ANT
CABLE
Black RF
Coaxial cable
(Supplied)
AERIAL
RF OUT
AUDIO RECEIVER
AERIAL
RF OUT
Advertisement
Table of Contents
