Adjusting Settings Via The Operating Menu; The Main Menu "Menu - Sennheiser EK 300 IEM G3 Instruction Manual

Adjusting settings via the operating menu

Adjusting settings via the operating
menu

The main menu "Menu"

Adjusting the squelch threshold – "Squelch"
SET
Squelch
Menu
Squelch
5dB
Call up "Squelch" Select the desired
setting
"Stored"
Adjustment range: 5 to 25 dBμV, adjustable in 2-dB steps, can be switched
off
The squelch eliminates annoying noise when the transmitter is switched
off or when there is no longer sufficient transmitter power received by the
receiver.
CAUTION! Danger of hearing damage!
If you switch the squelch off or adjust the squelch
threshold to a very low value, loud hissing noise can occur
in the receiver. The hissing noise can be loud enough to
cause hearing damage!
Always make sure that the squelch is switched on.
Before adjusting the squelch threshold, set the
volume of the headphone output
minimum (see page 9).
Never change the squelch threshold during a live
transmission.
Adjust the squelch threshold – with the transmitter switched off – to
the lowest possible setting that suppresses hissing noise.
A high squelch threshold reduces the transmission range.
The squelch should only be switched off for servicing purposes. With the
squelch threshold set to "5 dB", you switch the squelch off by keeping the
DOWN button pressed for 3 seconds.
Display Squelch is ...
... switched on.
519.150 MHz
The dotted line
ew300 IEM
threshold.
MUTE
P
RF AF
... switched off.
MHz
519.150
The dotted line
ew300 IEM
level display "AF" shows full deflection
P
RF AF
(hissing noise).
If you have accidentally switched off the squelch:
Press the UP button to switch the squelch on.
Scanning for, releasing and selecting frequency presets –
"Easy Setup"
Menu item Function of the menu item
Reset List Releases all locked frequency presets
Current List Selects an unused frequency preset
Scan New List Automatically scans for unused receiving frequencies
(frequency preset scan). If receiving frequencies are used,
they will be locked; if receiving frequencies are unused,
they will be released. After the frequency preset scan,
you can select an unused frequency preset.
14
Squelch
5 dB 15 dB
Store the setting
SET
PHONES to the
displays the squelch
goes off and the audio
Setting the frequency bank and the channel – "Frequency Preset"
SET
Frequency Preset
Menu
Frequency Preset B.Ch:
B.Ch: 1. 1
Call up "Frequency Select the
Preset" frequency bank
and confirm
"Stored"
When setting up multi-channel systems, please observe the
following:
Only the factory-preset receiving frequencies within one
frequency bank ("1" to "20") are intermodulation-free. It is vital
to observe the notes on frequency selection on page 21.
Overview of the frequency banks and channels:
Frequency bank Channels
"1" to "20" up to 16 per
frequency bank
"U1" to "U6" up to 16 per
frequency bank
Entering a name – "Name"
Name
Menu
Name L i c h a e l
L i c h a e l
Call up "Name" Enter a character
and confirm
"Stored"
Via the "Name" menu item, you can enter a freely selectable name (e.g. the
name of the performer) for the receiver. The name is displayed on the
"Frequency/Name" standard display (see page 10). The name can consist
of up to 8 characters such as:
• letters (without pronounciation marks),
• numbers from 0 to 9,
• special characters and spaces.
To enter a name, proceed as follows:
Press the UP/DOWN button
Press the SET button to change to the next segment/character
SET
or to store the complete entry.
Adjusting the balance – "Balance"
SET
Balance
Menu
Balance
0
Call up "Balance" Select the desired
setting
"Stored"
You can adjust the balance in 31 steps. In Focus mode (see next section)
and when one of the standard displays is shown, you can also use the UP/
DOWN button / to adjust the balance. The mode of operation of the
balance setting depends on the selected audio mode (see next section).
Adjusting settings via the operating menu
SET
Frequency Preset
1. 1 B.Ch: 6. 3
863.100MHz 824.500MHz
Select the channel;
store the setting
SET
Type
System bank:
frequencies are factory-preset
User bank:
frequencies are freely selectable
Name
Michael
Enter a character;
store the setting
/ to select a character.
Balance
0 5
Store the setting
SET
15