Adjust The Volume - Technics SA-DA10 Operating Instructions Manual

SA-DA10
+
4 5 6
–
7 8 9
DIRECT TUNING/
10/ENTER
DISC ENTER
MUTING
0 -/--
DISC/DECK 1/2 MD SOUND MODE SFC
DVD
SLOW/
DELAY
SEARCH
TOP MENU MENU LEVEL
+
ENTER
–
DISPLAY RETURN
SUB TITLE AUDIO ANGLE TEST
– +
GROUP PAGE DIMMER
– +
TV VOL TV/AV DVD 6CH
6
SA-DA10
SFC
SA-DA8
SFC
8
VOLUME
MIN MAX
8
SA-DA8
TAPE MD CD
TOP MENU DVD
6
DISC/DECK
ENTER
1/2
DISPLAY MENU
STEREO SURROUND SFC TEST
– +
DELAY LEVEL
DELAY
DIRECT TUNING/
1 2 3
DISC ENTER
LEVEL
4 5 6 10/–/– –
–, +
7 8 9 0
TV VOL
TV/AV DVD 6CH
– +
DIMMER MUTING VOL
HALL CLUB LIVE
SIM SURR THEATER
Enjoying the sounds
6
(if you selected SFC in step 5)
by remote control only
Press [SFC] to select the desired SFC
mode.
The mode changes each time you press the button while
the modes are displayed.
7
Start the source.
8

Adjust the volume.

While using the SFC modes
To adjust speaker level
q q q q q Press [LEVEL] to select the speaker channel to adjust.
Each time the button is subsequently pressed, the speaker
whose level is to be set is selected in the listed sequence.
C RS LS SW
Speakers for which "NONE" or "NO" has been set are skipped.
w w w w w Press [+] or [–] to adjust the output level.
Channels C, RS, LS, and SW can be adjusted between –10 dB
and +10 dB.
by remote control only
To adjust delay time
You can adjust surround channel only.
Adjust the delay time of the sound from the surround speakers to
produce the proper effect.
q q q q q Press [DELAY].
When you press the button, the current delay time is displayed.
w w w w w Press [+] or [–] to set the time.
Select a delay time to suit your individual needs.
Delay time can be set at 10 milliseconds (ms) intervals
between 10 and 100 ms.
The factory settings for each mode are 50 ms.
For your reference
Speaker level and delay time can be set for each SFC mode.
When you finish listening
Be sure to reduce the volume and press [
standby.
For your reference
¡ ¡ ¡ ¡ ¡ If you are using a VCR (connected to VCR 1) and you select
TAPE/MD (for the United Kingdom), TAPE (for Australia and
New Zealand), CD, TUNER, or PHONO
The picture will remain on the screen.
¡ ¡ ¡ ¡ ¡ About the DSP sound modes
The DSP sound modes can be set for each source. Once you
have set the mode for a source, the mode is engaged whenever
that source is selected.
These modes are automatically switched to STEREO if
SPEAKERS B is selected or both SPEAKERS A and B or BI-
WIRE are turned off. When SPEAKERS B is turned off or
SPEAKERS A or BI-WIRE is selected, the mode is switched
back to the latest mode.
¡ ¡ ¡ ¡ ¡ Only Dolby Digital, DTS or PCM signals (44.1 kHz or 48 kHz)
can be reproduced through the digital terminal
The digital input signal of sampling frequencies 96 kHz or 192
kHz and other signal formats such as MPEG cannot be
reproduced on this unit.
by remote control only
/l] to switch the unit to
23
RQT5518