Hedge Trimmer Safety Warnings; Additional Warnings - Homelite HLT33MTB Original Instructions Manual

Table of Contents

Advertisement

cut. This contact may cause the blade to stop for an
instant, and suddenly "thrust" the product away from the
object that was hit. This reaction can be violent enough
to cause the operator to lose control of the product.
Blade thrust may occur without warning if the blade
snags, stalls, or binds. This is more likely to occur in
areas where it is difficult to see the material being cut.
For cutting ease and safety, approach the weeds being
cut from the right to the left. In the event an unexpected
object or woody stock is encountered, this practice
could minimise the blade thrust reaction. Both hands
must be used at all times to control the product.

HEDGE TRIMMER SAFETY WARNINGS

Only start the engine when the hedge trimmer is in a
safe working position. The manufacturer recommends
that the product is placed on the ground where the
blades cannot contact anything before you start the
engine.
While operating the hedge trimmer, do not overreach
or stand on unstable support. Keep proper footing
and balance at all times. The manufacturer does not
recommend the use of steps or ladders.
To protect yourself from electrocution, do not operate
within 10 m of overhead electrical lines.
Do not operate the product with a damaged or
excessively-worn cutting device.
To reduce fire hazard, keep the engine and the silencer
free of debris, leaves, or excessive lubricant.
Always ensure that all handles and guards are fitted
when using the hedge trimmer. Never attempt to use
an incomplete hedge trimmer or one fitted with an
unauthorised modification.
Always use two hands to operate the hedge trimmer,
which is fitted with two handles.
Ensure before each use that all controls and safety
devices function correctly. Do not use the product if the
"O" (off) switch does not stop the engine. The defective
switch must be replaced by an authorised service
centre.
Inspect the hedge trimmer before each use. Check for
fuel leaks or loose fasteners, etc. Do not operate if fuel
is leaking or handles and guards are not secure and
fully functional.
If the cutting mechanism strikes any foreign object or
the hedge trimmer starts making any unusual noise or
vibration, shut off the power source and allow the hedge
trimmer to stop before taking the following steps:
inspect for damage
check for, and replace, any loose parts.
Damaged parts should be replaced or repaired
immediately with parts having equivalent specifications.
To stop the hedge trimmer in an emergency. Press the
on/off switch to the "O" (off) position.
Original instructions
Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect. Carbon
monoxide is a colourless, odourless, and an extremely
dangerous gas which can cause unconsciousness or
death.
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre before use.

ADDITIONAL WARNINGS

Do not touch the area around the silencer or engine of
the product, these parts get very hot during operation.
Do not modify the product in any way
Do not force the hedge trimmer through heavy
shrubbery. This can cause the blades to bind and slow
down. If the blades slow down, reduce the pace.
Do not attempt to cut stems or twigs that are larger
than 24 mm thick, or those obviously too large to feed
into the cutting blade. Use a non-powered hand saw or
pruning saw to trim large stems.
Ensure to keep a running or hot engine and silencer
well away from combustible materials to reduce the risk
of fire.
POLE PRUNER SAFETY WARNINGS
Do not use the product when there is a possibility of
thunderstorm or lightning. Store the product safely
indoors.
Ensure all guards, handles are properly fitted and are
in good condition.
Do not start using the product until you have a clear
work area, secure footing, and a planned retreat path
away from the falling branches or limbs.
Beware of the emission of lubricant mist and saw dust.
Wear mask or respirator if required.
During operation, hold the product with both hands. Use
one hand to firmly grasp the front hand grip. Use the
other hand to grasp the rear handle and operate the
trigger release and engine switch.
Cut only when visibility and light are adequate for you
to see clearly.
Do not use on a ladder or unstable support. Always cut
with both feet on solid ground to prevent being pulled
off balance.
To protect yourself from electrocution, do not operate
within 10 m of overhead electrical lines.
Before starting the engine, make sure the chain is not
contacting any object.
Always cut with the engine running at full speed. Fully
squeeze the throttle trigger and maintain a steady
| English
3

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents