Specific Safety Rules For Trimmer Use; Specification - Homelite HLT26CD User Manual

GB
F D E I
GENERAL SAFETY RULES
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician
about these symptoms.
Keep the tool well maintained, fasteners tightened
■
and worn parts replaced.
Mix and store fuel in a container approved for fuel.
■
Mix fuel outdoors where there are no sparks or flames.
■
Wipe up any fuel spillage. Move 9 m away from
refueling site before starting engine.
Stop the engine and allow to cool before refueling or
■
storing the unit.
Allow the engine to cool; empty the fuel tank and
■
secure the unit from moving before transporting in a
vehicle.
Weight
- Without fuel, without string head, without guard
- Without fuel with string head
Fuel tank volume
Cutting swath
Engine displacement
Line diameter
Maximum engine performance
(in accordance with ISO 8893)
Maximum rotational frequency
of the the spindle
Engine speed (rotational frequency)
at recommended max. spindle
rotational frequency
Engine speed (rotational frequency)
at idle
Fuel consumption (in accordance
with ISO 8893) at max.
engine performance
Specific fuel consumption
(in accordance with ISO 8893)
at max. engine performance
Vibration level idling
- Front handle
- Rear handle
Vibration level racing
- Front handle
- Rear handle
Sound pressure level
(in accordance with EN 27917)
Measured sound pressure level
Sound power level (in accordance
with ISO 10884)
P NL S DK N FIN GR HU

SPECIFICATION

[cm
(cm
[kg/h or (L/h)]
[g/kW.h or (L/kW.h)]
[LpA (dB A)]
[LwA (dB A)]
CZ RU RO PL SLO HR TR EST LT
English

SPECIFIC SAFETY RULES FOR TRIMMER USE

Replace bump head if cracked, chipped, or damaged
■
in anyway. Be sure the bump head is properly
installed and securely fastened. Failure to do so can
cause serious injury.
Make sure all guards, straps, deflectors and handles
■
are properly and securely attached.
Use only the manufacturer's replacement line in the
■
cutting head. Do not use any other cutting attachment.
Never operate unit without the safety guard in place
■
and in good condition.
Maintain a firm grip on both handles while trimming.
■
Keep bump head below waist level. Never cut with
the bump head located over 76 cm or more above the
ground.
HLT26CD
(kg)
3.61
3.95
3 or (L)] 300 or (0.3)
(mm) 432
3
/ cc) 26
(mm) 2.0
(kW) 0.65
(min- 1 ) 12,000
1
(min- ) 12,000
1
(min- ) 3,200-4,200
0.33 or (0.45)
508 or (0.7)
2
(m/s )
0.7
1.4
(m/s 2 )
2.0
3.0
100
(dB A) 106.3
108
11 11
LV
HLT26CDY HLT26CDSY
3.61 3.98
4.00 4.35
300 or (0.3) 300 or (0.3)
432 432
26 26
2.0 2.0
0.65 0.65
12,000 12,000
12,000 12,000
3,200-4,200 3,200-3,800
0.33 or (0.45) 0.33 or (0.45)
508 or (0.7) 508 or (0.7)
0.8 7.7
1.8 4.5
2.3 11.1
3.2 12.9
100 100
107 108
108 109
SK BG