Table of Contents
Advertisement
Original instructions
Never use cutting means or attachments, which are not
specified by HOMELITE in this manual. This includes
the use of metal multi-piece pivoting chains and flail-
blades. These items are known to break up during use
and present a high risk of serious injury to the operator
or bystanders.
Inspection after dropping or other impacts: Thoroughly
inspect the product and identify any problems or damage
to it. Any part that is damaged should be properly
repaired or replaced by an authorised service centre.
GRASS TRIMMER SAFETY WARNINGS
■
Replace the string head if cracked, chipped, or
damaged in any way. Be sure the string head is
properly installed and securely fastened. Failure to do
so can cause serious injury.
■
Avoid using on wet grass.
■
Do not walk backwards when using the product.
■
Walk, never run.
■
The small blade fitted to the cutting attachment guard
is designed to trim the new extended line to the correct
length for safe and optimum performance. It is very
sharp; do not touch it, particularly when cleaning the
product.
■
Always ensure that ventilation openings are kept clear
of debris.
■
Before use and after any impact, check that there are
no damaged parts. Examine the cutting means for signs
of cracking or other damage. A defective switch or any
part that is damaged should be properly repaired or
replaced by an authorised service facility.
■
Make sure the head attachment is properly installed
and securely fastened.
■
Make sure all guards, deflectors, handles, bolts, and
fasteners are properly and securely attached.
■
Do not modify the product in any way. This may
increase the risk of injury to yourself or others.
■
Use only the manufacturer's replacement line in the
cutting head. Do not use any other cutting attachment.
■
Do not operate the product without the cutting
attachment guard in place. Ensure the cutting
attachment is in good condition.
■
Maintain a firm grip on both handles while trimming.
Keep string head below waist level. Never cut with the
string head located more than 76 cm above the ground.
TRANSPORTATION AND STORAGE
■
Stop the engine and allow it to cool down before storing
or transporting.
■
Clean all foreign materials from the product.
■
Drain all fuel from tank into a container approved for
2
| English
WARNING
WARNING
petrol. Remember to properly replace and tighten the
fuel cap.
■
Run the engine until it stops, this will remove all fuel
that could become stale and leave varnish and gum in
the fuel system.
■
Drain all lubricant from tank into a container approved
for lubricant. Remember to properly replace the
lubricant cap.
■
Store the product in a cool, dry, and well-ventilated
place that is inaccessible to children. Keep away from
corrosive agents, such as garden chemicals and de-
icing salts. Do not store outdoors.
■
When transporting the product in a vehicle, secure it
against movement or falling to prevent injury to persons
or damage to the product.
■
Never carry or transport the product while the engine
is running.
■
Abide by all government and local regulations for the
safety storage and handling of petrol.
Short term
■
Stop the engine, and allow it to cool down before
storing.
■
Clean all foreign material from the product.
■
Store the product in a cool, dry, and well-ventilated
place that is inaccessible to children.
■
Keep away from corrosive agents such as garden
chemicals and de-icing salts.
■
Do not store outdoors.
MAINTENANCE
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
■
Always stop the engine and allow it to cool down before
making any maintenance.
■
You may make adjustments and repairs described in
this manual. For other repairs, contact an authorised
service centre.
■
Consequences of improper maintenance may include
additional safety hazards, excess carbon deposits
resulting in loss of performance, and discharge of black
lubricant residue dripping from the silencer.
■
For the replacement line, use only nylon filament line
of the diameter described in the specification table of
this manual.
■
After extending the new cutter line, always return the
product to its normal operating position before starting.
■
After each use, clean the product with a soft, dry cloth.
■
Any part that is damaged should be properly repaired or
replaced by an authorised service centre.
■
Check all nuts, bolts, and screws at frequent intervals
WARNING
Hide quick links:
Advertisement
Table of Contents
