Homelite HLT25SDS Original Instructions Manual page 9

CUTTING TIPS
When cutting, make sure the cutter head is at a slight angle
while still approximately parallel to the ground surface. In
tall grass, cut from the top down to ensure the moving parts
do not get tangled with the long grass.
If grass becomes wrapped around the trimmer head, stop
the engine, wait for all moving parts to stop and remove
the grass.
ADVANCING THE LINE (HLT25SDS)
If the line becomes short, tap the bump head on the ground
as shown at full throttle. More line will extend. Take care
not to bump the head on a hard surface such as concrete
or pavers as this may cause damage to the bump head.
WARNING
When servicing, use only original manufacturer's
replacement parts. Use of any other parts may create a
hazard or cause product damage.
WARNING
Always wear safety goggles or safety glasses with side
shields during product operation. If operation is dusty,
also wear a dust mask.
WARNING
Before inspecting, cleaning, or servicing the product,
shut off the engine, wait for all moving parts to stop.
Failure to follow these instructions can result in serious
personal injury or property damage.
WARNING
Neglected or poorly conducted maintenance may create
additional hazards. Do not attempt to repair or maintain
the product if you are not qualified to do so. If in doubt,
return to a service centre for professional assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, lubricant, and grease.
WARNING
Do not at any time let brake fluids, petrol, petroleum-
based products, penetrating lubricants, etc., come in
contact with plastic parts. Chemicals can damage,
weaken or destroy plastic, which may result in serious
personal injury.
You can often make adjustments and repairs described in
this manual. For other repairs, have the trimmer serviced
Original instructions
by a service agent.
REPLACING THE LINE (HLT25SDS)
■ Ensure the product is in "STOP" (OFF) position.
■ Unlock the retainer clockwise and then remove the
retainer and spool.
■ Remove all old cutter line, and replace with the correct
replacement line (diameter- 2.4 mm, length-1.8 m x 2
pcs.).
■ Once you have reloaded the line on the spool, locate it
in the correct channels.
■ Replace the spool back into the head making sure all
the lines are located correctly.
■ Have 15 cm of line protruding from each of the eyelets
of the string head housing.
■ Press the head into the drive shaft of lower boom to
hold it steady.
■ Replace the retainer
counterclockwise.
■ Pull excess line out to ensure no tangles in the head.
REPLACING THE PRO CUT I STRING HEAD AND LINE
(HLT25CDS)
■ Stop the engine and wait for all moving parts to stop
completely.
■ Loosen the spool retainer by turning it counterclockwise
and then remove the string head.
■ Take a new PRO-CUT I string head and a 500 mm
length of 2.4 mm diameter monofilament pre-cut line.
■ Place the middle of the line under the hook/notch inside
the spool.
■ Feed the ends of the line through the eyelets on the
side of the PRO-CUT I fixed line head.
■ Pull the line outwards so it is tight and even on both
sides of the spool.
■ Install the PRO-CUT I head assembly on the drive shaft
and then secure with spool retainer
CLEANING THE EXHAUST PORT AND SILENCER
Depending on the type of fuel used, the type and amount
of lubricant used, and/or your operating conditions, the
exhaust port and silencer may become blocked with
carbon deposits. If you notice a power loss with your petrol
powered product, a qualified service technician will need to
remove these deposits to restore performance.
SPARK ARRESTOR
The spark arrestor must be cleaned or replaced every
25 hours of operation or yearly to ensure proper
performance of the product. Spark arrestors may be found
in different locations depending on the model purchased.
Please contact your nearest service centre for the location
of the spark arrestor for your model.
| English
and then tighten it
7