Sony HDCU1000 Installation Manual page 98

Page Menu / Menu Image
C06 INCOM/PGM
<INCOM/PGM>
FP-INCOM
(MIC ON) (PRIVATE)
PGM-MODE : OFF
PGM-SEL : MIX
PGM1 : 0
PGM2 : 0
SIDE TONE: 0
INCOM-CH : 2CH
C07 PROMPT/TRUNK
<PROMPT/TRUNK> ?C07 TOP
PROMPTER: 1CH
TRUNK SETTING
CH : 2CH
IF : 232C
C08 VIDEO SETUP
<VIDEO SETUP> ?C08 TOP
SETUP : OFF
Q FILTER : WD
G/Y SYNC : OFF
VCS RELAY : ON
C08 VIDEO SETUP *
<VIDEO SETUP> ?C08 TOP
SETUP : OFF
SD BLK CLP: OFF
Q FILTER : WD
G/Y SYNC : OFF
VCS RELAY : ON
C09 VIDEO ADJUST
(When using EN-159 board)
<VIDEO ADJUST 1> C09 TOP
VBS LEVEL :
CHROMA:
PIX LEVEL :
CHROMA:
WFM LEVEL :
CHROMA:
: The settings in the box are default values.
3-24 (E)
Item
FP-INCOM
C06 TOP
PGM-MODE
PGM-SEL
PGM1
PGM2
SIDE TONE
INCOM-CH
PROMPTER
TRUNK SETTING
CH
IF
SETUP
Q FILTER
G/Y SYNC
VCS RELAY
SETUP
SD BLK CLP
Q FILTER
G/Y SYNC
VCS RELAY
VBS
LEVEL
CHROMA
0
PIX
0
0
LEVEL
0
0
CHROMA
0
WFM
LEVEL
CHROMA
* : This function has been added to software V1.20 and the later versions.
Setting Description
(MIC ON/OFF/PGM ON) Displays the FRONT INCOM MIC SW
settings.
(PROD/ENG/PRIVATE) Displays the FRONT INCOM line
settings.
SEP/MIX/ OFF Sets the PGM-MODE output.
MIX/ PGM1 /PGM2 Selects the PGM-MODE.
_99 to 0 to +99 Sets PGM1 level.
_99 to 0 to +99 Sets PGM2 level.
_99 to 0 to +99 Sets SIDE TONE level.
1CH/ 2CH Selects INCOME CHANNEL.
1CH /2CH Sets line number for Prompter (Fixed to
1 channel for HDCU1500.)
Sets line for TRUNK.
Sets the channel number used.
Sets the communication line mode.
1CH/ 2CH
232C /422A
OFF /ON Turns ON/OFF the SETUP.
WD /NA Sets width of Q-Filter. (Only when the
EN board is attached)
OFF/ ON Turns ON/OFF Gch-SYNC for the R/G/B
component signal.
(Only when the EN board is attached)
OFF/ ON Sets PIX/WFM terminal output mode.
(Only when the EN board is attached)
OFF /ON Turns ON/OFF the SETUP.
OFF /ON Clips the Y signal of lower than 0% to be
supplied from the SD SDI output
connector, at 0%
WD /NA Sets width of Q-Filter. (Only when the
EN board is attached)
OFF/ ON Turns ON/OFF Gch-SYNC for the R/G/B
component signal.
(Only when the EN board is attached)
OFF/ ON Sets PIX/WFM terminal output mode.
(Only when the EN board is attached)
Adjusts the VBS output video level.
_99 to 0 to +99
_99 to 0 to +99
Adjusts the PIX output video level.
_99 to 0 to +99
_99 to 0 to +99
Adjusts the WFM output video level.
_99 to 0 to +99
_99 to 0 to +99
. IM/HDCU1000 Series