Related Manuals for Sony NSS-S2
Summary of Contents for Sony NSS-S2
- Page 1 MEDIA STORAGE UNIT NSS-S2 INSTALLATION MANUAL 1st Edition (Revised 1) Serial No. 10001 and Higher...
- Page 2 Beim Einbau des Geräts ist daher im Festkabel ein leicht zugänglicher Unterbrecher einzufügen, oder das Netzkabel mu ß mit einer in der Nähe des Geräts befindlichen, leicht zugänglichen Wandsteckdose verbunden werden, damit sich bei einer Funktionsstörung die Stromversorgung zum Gerät jederzeit unterbrechen lä ß t. NSS-S2...
- Page 3 6. When performing the installation, keep the The use of optical instruments with this product following space away from walls in order to will increase eye hazard. obtain proper exhaust and radiation of heat. Rear: 10 cm (4 inches) or more 1 (P) NSS-S2...
- Page 4 Carrying the unit with less than two persons may cause injury. Mount with more than two persons The total weight of this unit is 32 kg. Mounting the unit with less than two persons may cause injury. 2 (P) NSS-S2...
-
Page 5: Table Of Contents
2-1. Cleaning the Air Filter ..........2-1 (E) 2-2. Functional Descriptions of Board Switches and LEDs ..............2-2 (E) 2-2-1. PU-124 Board ..........2-2 (E) 2-2-2. MPU-136 Board ..........2-8 (E) 2-2-3. DP-405 Board ..........2-10 (E) 1 (E) NSS-S2... -
Page 7: Manual Structure
Related manuals Besides this Installation Manual, the following manuals are available for the NSS-S2..NSS-S2 Operation Manual (supplied with the NSS-S2) This manual describes the application and operation of the NSS-S2. Part number: 3-903-843-XX ..NSS-S2 Maintenance Manual (available on request) -
Page 9: Installation
Cautions when an error appears in a HDD . Treat this unit conform to the above cautions, even when an error appeared. . Keep the unit in the condition in which the error appeared, and record the details of the error. 1-1 (E) NSS-S2... -
Page 10: Installation Procedure
The rear side of this unit should be 10 cm away from Installing the the walls for ventilation. 1-7. Installing the HDD Unit HDD unit Connection 1-8. Signal Input and Output 1-9. Connecting Connectors and Cables 1-10. Connection Checks after connection 1-11. Checks after Connection 1-2 (E) NSS-S2... - Page 11 . If the power is turned on with the cabinet removed, the air-cooling effect of the fan is greatly reduced which can result in damaging the PU-124 board and HDD or its data. Avoid the operation when the cabinet is removed. (440) 263.5 35.4 115.5 MEDIA STORAGE UNIT NSS-S2 POWER SYSTEM BUSY 469.5 Unit : mm 1-3 (E)
-
Page 12: Power Supply
3-613-640-01 AC inlet If the unit is used in the area except above, please contact your local Sony Sales Office/Service Center. . Use the specified power cord only. . Do not damage to the power cord. . Ground the unit safely. -
Page 13: Setting The Switch For The Backup Battery
1. Remove the two screws and pull out the PU-124 board assembly in the direction of the arrow while holding the handle. Handle PU-124 board assembly 3. Install the PU-124 board assembly by reversing step 1. B3 x 6 PU-124 board Handle assembly 1-5 (E) NSS-S2... -
Page 14: Rack Mounting
. Adaptor fixing screws (B4 x 10: 7-682-562-09) : 6 pcs Required other parts To mount the unit in the rack, the following parts are required. (supplied with the NSS-S2) . Screw (RK5 x 16: 7-682-378-04) : 4 pcs B4 x 6 . - Page 15 Rack angle Ornamental washers 31.75 RK5 x 16 B4 x 10 Ornamental washers B4 x 10 31.75 RK5 x 16 Rack angle Unit : mm 6. Fasten the length adjustment screws which are loos- ened in step 4. 1-7 (E) NSS-S2...
-
Page 16: Installing The Hdd Unit
Board facing up Cushion 1. Fully loosen the two screws (with drop-safe) and remove the front panel. HDD unit 2. Open the control panel. HDD No. label Control panel Levers Screws (with drop-safe) Screws Front panel (with drop-safe) 1-8 (E) NSS-S2... -
Page 17: Signal Input And Output
When connecting cables to various connectors on the rear panel at the time of installing or servicing, connect the following connectors/cable or their equivalents. NSS-S2 Matching Connector/Cable Panel Indication Connector Connector/Cable Sony Part No. 100BASE-TX Modular jack RJ45 UTP (Unshielded twisted-pair) cable FIBRE CHANNEL... -
Page 18: Connection
1-10. Connection The connection of the 12 I/O configuration is as follows. Connect two units of NSS-V2 and two units of NSS-S2 via the fiber channel. Connect the LOCAL Ethernet and the GLOBAL Ethernet as shown in the following figure. -
Page 19: Checks After Connection
1-11. Checks after Connection Followings are check items after connection. Confirm that the unit operates normally by checking each item. FRONT MEDIA STORAGE UNIT NSS-S2 POWER SYSTEM BUSY 1 2 3 REAR No. Check Item Check Countermeasure/Status Check the lighting color of the POWER Green The two power units are running normally. - Page 20 An abnormality ocurred in the corresponding (Lights on) . Or HDD is not installed. FRONT * 1) : When replacing the power unit, refer to the Maintenance Manual. * 2) : Refer to the Maintenance Manual for the HDD unit removal procedure. 1-12 (E) NSS-S2...
-
Page 21: Menu Settings
3. Press [ENTER] key to open the CONFIGURATION menu screen. SERIAL 10001 Returning to MAIN menu screen 1. On the CONFIGURATION menu screen, display the “EXIT” using [UP] or [DOWN] key. EXIT: ENT 2. Press [ENTER] key to return to the CONSOL MENU screen. 1-13 (E) NSS-S2... -
Page 22: Setting Of Device Name
5. After selecting the last character, press [ENTER] key. 6. The check screen is displayed. CHANGE Set the cursor to OK using [RIGHT] or [LEFT] key and press [ENTER] key. 7. The device name is set and the display returns to the CONFIGURATION menu screen. 1-14 (E) NSS-S2... -
Page 23: Setting Of Network
7. Set a subnet mask in the same procedure as steps 3 and 4. 8. Display the “DEFAULT GATEWAY” using [UP] or [DOWN] key. DEFAULT GATEWAY 192.168.000.254 9. Set a gateway in the same procedure as steps 3 and 4. 1-15 (E) NSS-S2... -
Page 24: Executing Of Logical Formatting
4. Press [ENTER] key without changing the screen. 5. The check screen is displayed. EXECUTE ABORT Set the cursor to OK using [RIGHT] or [LEFT] key and press [ENTER] key. EXECUTE SUCCESS 6. Press [ENTER] key to return to the CONFIGURATION menu screen. 1-16 (E) NSS-S2... -
Page 25: Snmp
TRAP IP Settings: Default setting is “0.0.0.0”. ; Set up using the control panel menu. For each MIB structure, get information and description of trap sent from NSS-S2 to SNMP Manager, refer to the maintenance manual of NSS-S2. 1-13-1. Setting of Community Name 1. -
Page 26: Setting Of Trap Ip
3. Press [ENTER] key. When the cursor appeared, change to ON from OFF using [UP] or [DOWN] key and press [ENTER] key. FAN SILENT 4. The check screen is displayed. CHANGE Set the cursor to OK using [RIGHT] or [LEFT] key and press [ENTER] key. 1-18 (E) NSS-S2... -
Page 27: Service Overview
Clean the filter periodically. Cleaning 1. Turn off the main power of the NSS-S2. 2. Remove the front panel. (Refer to Section 1-7.) 3. Remove the filter in the direction of the arrow. -
Page 28: Functional Descriptions Of Board Switches And Leds
(A-4) FPGA(IC1601) setting For hard-debug (do not change except for factory switch setting) S1502-1, 2, 8 ON : For normal use 1 2 3 4 5 6 7 8 S1502-3 to 7 OFF : For normal use 2-2 (E) NSS-S2... - Page 29 *4 : JTAG : RAID_FPGA (using download tool) S4501 (E-7) FPGA (IC4501) For hard-debug (do not change except for factory All OFF setting switch setting) S4501-1 to 8 all OFF : For normal use 1 2 3 4 5 6 7 8 2-3 (E) NSS-S2...
- Page 30 Lights on (G-8) output is complete. D4501 (G-9) Green RAID_FPGA__STATUS0 Circuit board operation status. When the two PU- Lights on or off 124 boards are installed, the operation side lights up and the backup side lights out. 2-4 (E) NSS-S2...
- Page 31 Lights off D8006 (H-3) SASX12_LSI1_FAULT6 Lights off D8007 (H-3) SASX12_LSI1_FAULT5 Lights off D8008 (H-3) SASX12_LSI1_FAULT4 Lights off D8009 (H-3) SASX12_LSI1_FAULT3 Lights off D8010 (H-3) SASX12_LSI1_FAULT2 Lights off D8011 (J-3) SASX12_LSI1_FAULT1 Lights off D8012 (J-3) SASX12_LSI1_FAULT0 Lights on 2-5 (E) NSS-S2...
- Page 32 Lights off D8506 (G-3) SASX12_LSI2_FAULT6 Lights off D8507 (G-3) SASX12_LSI2_FAULT5 Lights off D8508 (G-3) SASX12_LSI2_FAULT4 Lights off D8509 (G-3) SASX12_LSI2_FAULT3 Lights off D8510 (G-3) SASX12_LSI2_FAULT2 Lights off D8511 (G-3) SASX12_LSI2_FAULT1 Lights off D8512 (G-3) SASX12_LSI2_FAULT0 Lights off 2-6 (E) NSS-S2...
- Page 33 Green SASX12_LSI2_STATUS2 Lights off D8535 (G-3) Green SASX12_LSI2_STATUS1 Lights off D8536 (G-3) Green SASX12_LSI2_STATUS0 Lights off D8537 (G-3) Green SASX12_LSI2_GPIO3 For design purpose Lights off D8538 (G-3) Green SASX12_LSI2_GPIO2 D8539 (G-3) Green SASX12_LSI2_GPIO1 D8540 (G-3) Green SASX12_LSI2_GPIO0 2-7 (E) NSS-S2...
-
Page 34: Mpu-136 Board
S701-6 ON : RIO-ID OFF : RIO-ID S701-7 ON : PCI (-X) Wide 32 bit OFF : PCI (-X) Wide 62 bit S701-8 ON : PCI Mode OFF : PCI-X Mode (B-5) Reset switch Initializes the MPU-136 board. 2-8 (E) NSS-S2... - Page 35 Lights off D702 (G-1) Green Lights off D703 (G-1) Green Lights off D704 (G-1) Green Lights off D705 (G-1) Green Lights off D706 (G-1) Green Lights off D707 (G-1) Green Lights on D708 (G-1) Green Lights on 2-9 (E) NSS-S2...
-
Page 36: Dp-405 Board
1 2 3 4 S107-3, 4 : Not used S108 (E-1) RS-232C#1 “2” side (the side without ): For hard-debug “2” side selection switch (do not change except for factory setting) “3” side (the side with ): EXP 2-10 (E) NSS-S2... - Page 37 +5 V Lights when the DD converter output voltage Lights on (+5.0 V) is generated. D114 (E-1) Blue +12V_IN Lights when the voltage immediately after Lights on the fuse of +12V is input from the power supply. 2-11 (E) NSS-S2...
- Page 39 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
-
Page 40: Sony Corporation
Printed in Japan Sony Corporation NSS-S2 (SY) J, E 2006. 12 16 3-903-855-02 ©2005...