Kenwood TS-940S Instruction Manual page 10

FRONT PANEL
CD
VOX switch ¢ page 24
®
POWER switch
®
CW break-in selector switch ¢ page 23
®
MONI (monitor) switch¢ pages 8,1 0, 14, 16
®TIMER switch¢ page 38
®
DIM (Dimmer) switch¢ page 19
(J) A TT switch ¢ page 24
®
AGC switch¢ page 25
®
Meter¢ page 20
®METER switch¢ page 20
([]) Main display
©
F. LOCK indicator¢ page 19
@ON AIR indicator¢ page 19
(j]l VFO A indicator¢ page 19
@.@ ANT TUNE indicator¢ page 19
@ VFO B indicator¢ page 19
@MEMO (Memory) channel indicator¢ page 19
@
SPLIT indicator¢ page 19
®
RIT indicator¢ page 19
®
XIT indicator¢ page 19
Q~
NOTCH indicator¢ page 19
®
MS (Memory scan) switch¢ page 33
®
CLOCK switch¢ page 35
®
Sub-display¢ page 35
®
PG. S (Program scan) switch¢ page 33
®
GRAPH switch¢ pages 35, 36
@ HOLD switch¢ page 33
®
SCROLL switch¢ pages 34, 35
®
SET switch¢ page 35
@ M. CE switch¢ page 34
@ RIT switch¢ page 26
@ RIT /X IT control¢ page 26
~NOTCH
control¢ page 22
@
XIT switch¢ page 26
®
SOL control¢ pages 9, 13, 15, 17
®
CLEAR switch¢ page 26
@ RF (gain) control¢ page 25
@ PITCH control¢ page 26
®
NOTCH switch¢ page 22
@]) AF TUNE control¢ page 26
@
AF TUNE switch¢ page 26
@
REC/SEND stand-by switch¢ pages 9, 11, 15, 17
@ MIC (Microphone) connector¢ pages 7, 29
@ PHONES jack¢ pages 7, 29
@ AUTO-THRU selector switch¢ page 18
@ NAR/WIDE switch¢ pages 10, 12
@ NB 1 switch¢ page 22
@
NB control¢ page 22
®
NB 2 switch¢ page 22
®
PROC switch ¢ page 24
~p
PROCESSOR-IN control¢ page 24
$]) PROCESSOR-OUT control¢ page 24
~
MIC (microphone gain) control¢ pages 9, 15
~·~
PWR (RF power) control¢ pages 8, 10, 14, 16
@ MODE switch¢ pages 8 ~ 17
®
Main tuning control¢ pages 8
~
17
®
T-F SET switch¢ page 20
®
A/B switch¢ page 19
®
VOICE switch¢ page 19
®
F. LOCK switch¢ page 19
®
A= B switch ¢ page 19
®
SPLIT switch ¢ page 19
I@ VFO/M switch¢ page 31
®
1 MHz step switch¢ pages 8
~
17
®
M
~
VFO switch¢ page 33
®
M. IN switch¢ page 31
@
BAND KEY (1 - 1 0) switch¢ pages 8
~
17
(@)
AT. T switch ¢ page 18
®
ENT (Enter) switch¢ page 34
®
VBTcontrol ¢page 21
©
AF (audio gain) control¢ page 26
@ SSB SLOPE TUNE HIGH CUT control¢ page 21
@ SSB SLOPE TUNE LOW CUT control¢ page 21
REAR PANNEL
CD
Antenna connector
Connect an antenna with an impedance of 50
Q,
with
an SWR of 1.5 or less.
®
GND (ground) terminal
Used to make TS-9405 ground. Connect using as thick
and short a wire as possible.
®
RX ANT terminal selector switch
Used to disconnect the TS-9405 receiver. Supplies an
antenna connection to an external receiver.
®
Transverter connector
For details, see page 29.
®
Remote connector
This connector is used when a linear amplifier is used.
@IF OUT jack
IF 1 is for connection to the SM-220 for Pan Display.
(8.83 MHz)
IF 2 is for connection to the SM-220 for RX Modulation
Display. ( 1 00 kHz)
(])PHONE PATCH jacks
The IN terminal is used for transmit audio from the
phone patch (600
Q ).
The OUT terminal is used for received audio from the
transceiver to the phone patch (600
Q ).
These jacks
can also be used for input to and from SSTV, or RTTY
terminals.
@ RTTY jack
For connection to an RTTY interface unit. (direct keying)
@
EXT SP (external speaker)
This terminal is for an external speaker.
@) CW KEY jack
Used to connect the key during use of CW.
®
Accessory terminals
@ Fuse Holder
@
AC power connector
Connect the supplied power cord.
@VOLTAGE SELECTOR switch
Used to select the correct line voltage.