Not Available For Fwd30 And Fwd45 - Trane Sintesis Advantage CGAF Series Installation Operation & Maintenance

Pre-Start Checkout
WARNING! It is imperative that L1, L2, and L3 in the
starter be connected in the A-BC phase sequence to
prevent equipment damage due to reverse rotation.
WARNING!To prevent injury or death due to
FWD
electrocution, take extreme care when performing
Power supply
service procedures with electrical power energized.
Capacities
Cooling capacity on water (1)
Heating capacity on water (2)
CAUTION! Do not interchange any load leads that are
Fan motor
from the unit contactors or the motor terminals. Doing
Fan power input (3)
Current amps (3)
so may damage the equipment.
Start-up amps
Air flow
Water System Flow Rates
minimum
nominal
Establish a balanced chilled-water flow through the
maximum
evaporator. The flow rates should be between the
Main coil
minimum and maximum values given on the pressure
Water entering/leaving connections
drop curves.
Electric heater (accessory for blower only)
Electric power supply
Water System Pressure Drop
Heating capacity
Hot water coil (accessory for blower only)
Measure the water-pressure drop through the evaporator
Heating capacity (4)
on the field installed pressure taps on the system water
G2 filter (filter box accessory)
piping. Use the same gauge for each measurement. Do
Quantity
Dimensions ( LxWxth)
not include valves, strainers, or fittings in the pressure
G4 filter (filter box accessory)
drop readings.
Quantity
Dimensions ( LxWxth)
Integrated Pump Package (Optional)
Condensate pump (accessory)
Water flow - lift height
Before starting up the pump, the pipe system must be

Not available for FWD30 and FWD45

thoroughly cleaned, flushed and filled with clean water. Sound level (L/M/H speed)
Sound pressure level (5)
Do not start the pump until it has been vented. To ensure
Sound power level (5)
correct venting, open the vent screw located on the
Unit dimensions
pump housing on the suction side (see next figure).
Width x Depth
Height
Figure 24 – Pump Package Shipped unit dimensions
Width x Depth
Height
Weight
Colour
Recommended fuse size
Unit alone (aM/gI)
Unit with electric heater (gI)
(1) Conditions: Water entering/leaving temperature: 7/12 °C, Air inlet temperature 27/19°C DB/WB - Nominal air flow
(2) Conditions: Water entering/leaving temperature: 50/45 °C, Air inlet temperature 20°C DB - Nominal air flow
(3) At high speed with nominal air flow.
(4) Water entering/leaving temperature 90/70 °C, air inlet temperature 20 °C DB, Nominal air flow.
(5) A rectangular glass wool duct 1m50 long is placed on the blower.The measurement is taken in the room containing the blower unit.
Heat exchanger operating limits:
FWD:
*water temperature: max 100° C
*absolute service pressure: min 1 bar/max 11 bars
Accessories - Hot water coil:
*water temperature: min. +2° C/max. 100° C
*absolute service pressure: min 1 bar/max 11 bars
CAUTION! When using freeze inhibitor, never fill the
system with pure glycol; this will damage the shaft seal.
Always fill the system with diluted solution. Maximum
concentration of glycol is 40% for unit with pump
package.
CAUTION! Failure to operate pump w/o water or insert
high glycol concentration will lead to premature seal
damage and void the warranty.
4 62
Technical Data
If the chiller is installed in a humid environment or a
location with high air humidity, the bottom drain hole
on the pump motor should be opened. The enclosure
class of the motor is then changed from IP55 to IP44. The
function of the drain holes is to drain off water which has
08
entered the stator housing with air humidity.
(V/Ph/Hz)
Tracer UC800 Set-Up
(kW) 5,2
(kW) 6,3
Using Tracer TU service tool, adjust the settings. Refer to
(type)
(kW) 0,23
Tracer TU manual and UC800 user guide for instruction
(A) 1,1
on settings.
(A) 3,2
(m /h) 490 CAUTION! To prevent compressor damage, do not
3
(m /h) 820
3
operate the unit until all refrigerant valves and oil-line
(m /h) 980
3
service valves are opened.
(type)
(Dia) 3/4"
IMPORTANT! A clear sight glass alone does not mean
that the system is properly charged. Also check system
(V/Ph/Hz) 230/1/50
discharge superheat, approach temperature and unit
(kW) 2/4
operating pressures.
(kW) 6,3
2
(mm) 386x221x8
-
(mm) -
(type)
(l/h - mm)
(dB(A)) 36/40/43
(dB(A)) 46/50/53
(mm) 890 x 600
(mm) 250
(mm) 933 x 644
(mm) 260
(kg) 32
(A) 8/16
(A) 16 (2kW),25 (4kW)
12 20
230/1/50
8,3 15
11,9 18,9
2 x direct drive centrifugal
0,46 0,65
2,2 3,1
5,5 9,3
980 1400
1650 2300
1970 2600
ISO R7 rotating female
3/4" 1 1/2"
230/1/50 or 400/3/50 400/3/50
8 10
12 17,4
2 2
486x271x8 586x321x8
2 2
486x264x48 586x314x48
Centrifugal
24 - 500
38/41/44 46/50/53
48/51/54 56/60/63
1090 x 710 1290 x 820
300 350
1133 x 754 1333 x 864
310 360
46 61
galvanised steel
8/16 8/16
40 (230V),3*16 (400V) 3*20
30 45
18,8 30,1
20,9 38,2
1,04 1,51
4,7 5,5
14,1 16,5
1800 2700
3000 4500
3600 5400
1 1/2" 1 1/2"
400/3/50 400/3/50
12 12
22,4 34,5
2 2
586*421*8 586*621*8
2 2
586*414*48 586*614*48
47/52/57 47/52/58
57/62/67 57/62/68
1290 x 970 1290 x 1090
450 650
1333 x 1008 1333*1133
460 660
76 118
8/25 8/25
3*25 3*25
CG-SVX039B-GB UNT-PRC002-GB