Carrier 48LC Series Controls, Start-Up, Operation And Troubleshooting page 96

Display Text
OUTPUTS
GENERAL OUTPUTS
IDF SPEED OUTPUT
ECON CMD POSITION
RHT DISCH VALVE A
COOLING LV A
CCH RELAY
PE1 RELAY
PE2 RELAY
ALARM RELAY
DD IDF HI SPD RLY
DD IDF MD SPD RLY
DD IDF LO SPD RLY
COOLING OUTPUTS
COMPRESSOR A1
COMPRESSOR A2
COMMANDED ODF SPD
ODF SPEED OUT 1
ODF SPEED OUT 2
ODF SPEED OUT 3
HEATING OUTPUTS
HEAT 1 RELAY
HEAT 2 RELAY
Display Text
USB
DATA ACQUISITION
TREND STATUS
TREND DURATION
TREND RATE
TREND POINTS FROM
TREND FROM USB FILE?
TREND FROM PRELIST?
EQUIP PERFORMANCE
GEN. INPUT/OUTPUT
COOL PERFORMANCE
HEAT PERFORMANCE
COOL DIAGNOSTIC
IDF DIAGNOSTIC
VENT DIAGNOSTIC
TREND GO?
SAVE CONFIGS TO FILE
SAVE CONFIGS
SAVE CONFIG STATUS
SAVE CONFIGS FROM FILE
FIND CONFIG FILE
FILE TRANSFER
BACKUP SERVICE FILES
UPGRADE SOFTWARE
FIND APPLICATION FILE
APPENDIX A: SystemVut Controller Display
Outputs Main Menu Layout
Expanded Text
Outputs Menu
General Outputs Menu
Commanded IDF Speed
Econo Commanded Position
Reheat Dischg Valve CirA
Cooling Liq Valve CirA
CCH Relay 1 State
Power Exhaust 1 Relay
Power Exhaust 2 Relay
Alarm Output Relay State
DD IDF high speed relay
DD IDF med. Speed relay
DD IDF low speed relay
Cooling Outputs Menu
Circuit A Compressor 1
Circuit A Compressor 2
Commanded ODF Speed
ODF Speed Signal Output1
ODF Speed Signal Output2
ODF Speed Signal Output3
Heating Outputs Menu
Heat Stage 1 Relay
Heat Stage 2 Relay
USB Main Menu Layout
Expanded Text
USB Menu
Data Acquisition Menu
USB TREND STATUS
USB TREND DURATION
USB TREND RATE
USB TREND POINTS FROM
TREND FROM USB FILE MENU
TREND FROM PRELIST MENU
TREND EQUIP PERFORMANCE
TREND GEN INPUTS/OUTPUTS
TREND COOL PERFORMANCE
TREND HEAT PERFORMANCE
TREND COOLING DIAGNOSTIC
TREND IDF DIAGNOSTIC
TREND VENTILATION
Start USB Trending
Save Configuration to file
Make Config Backup File
Backup File is ready
Save Configuration from file
USB Find Restore File
File Transfer Menu
BACKUP SERVICE FILES
Upgrade Software Menu
USB search for app file
Values Units
0 to 100 %
0 to 100 %
Enable/Disable
Enable/Disable
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
xxxx rpm
xxxx rpm
xxxx rpm
xxxx rpm
On/Off
On/Off
Values Units
0=IDLE,
1=TRENDING,
2=NO POINTS,
3=USB FULL
0=1 MINUTE,
1=5 MINUTES,
2=15 MINUTES,
3=30 MINUTES,
4=1 HOUR,
5=3 HOURS,
6=8 HOURS,
7=12 HOURS,
8=1 DAYS,
9=1.5 DAYS,
10=2 DAYS,
11=3 DAYS,
12=5 DAYS,
13=1 WEEK,
14=2 WEEK,
15=4 WEEK,
16=USB FULL
1 to 300
0=FILE,
1=LIST
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
Yes/No
Start/Stop
0=IDLE,
1=SUCCESS,
2=FAILURE
Yes/No
Yes/No
96
Write Status Point
FANSPEED
Forcible DAMPCMD
RDV_A
CLV_A
CCHR1
Forcible PE1
Forcible PE2
Forcible ALMOUT
FSPDHRLY
FSPDMRLY
FSPDLRLY
COMP_A1
COMP_A2
ODFSPD
ODF1SPD
ODF2SPD
ODF3SPD
HEAT_1
HEAT_2
Write Status Point
TRNDSTAT
Command TRNDDUR
Command TRNDRATE
Command TRNDPNTS
Command TRNDEQPR
Command TRNDIO
Command TRNDCLPR
Command TRNDHTPR
Command TRNDCLDG
Command TRNDIDF
Command TRNDVENT
Command TREND_EN
Command DDBCKUP
BACKUP_R
Command BACKFILE
Command APPFILE