Fisher & Paykel OB60 Series Installation Manual
Hide thumbs
Also See for OB60 Series:
- User manual (72 pages) ,
- Installation instructions and user manual (60 pages) ,
- Care and cleaning (15 pages)
Related Manuals for Fisher & Paykel OB60 Series
Summary of Contents for Fisher & Paykel OB60 Series
- Page 1 BUILT IN OVEN OB60 models INSTALLATION GUIDE NZ AU GB IE 591785A / 1105822-ß0 02.19...
-
Page 2: Safety And Warnings
SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS WARNING ! Electrical shock hazard To avoid hazard, follow these instructions carefully Always disconnect the appliance from the before installing or using this appliance: mains power supply before carrying out any Make this information available to the person maintenance or repairs. -
Page 3: Prior To Installation
PRIOR TO INSTALLATION IMPORTANT! Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture-proofing the oven cavity. Before you install the oven, make sure: the benchtop and oven cavity are square and level, and are the required dimensions. - Page 4 PRODUCT DIMENSIONS (OB60S, OB60N MODELS) FRONT SIDE OB60S MODELS OB60N MODELS PRODUCT DIMENSIONS (MM) (MM) Overall height* of product 450** Overall width of product Overall depth of product (excluding handle and knobs) Height of chassis Width of chassis Depth of chassis Depth of oven frame and control panel (distance between front of chassis and front of oven door, excluding knobs) Depth of oven door when fully open...
- Page 5 CABINETRY DIMENSIONS (OB60S, OB60N MODELS) Electrical supply 16–20 mm 20 mm min. 1.5 mm SIDE OB60S MODELS OB60N MODELS CABINETRY DIMENSIONS (MM) (MM) Minimum inside width of cavity Overall width of cavity Inside height of cavity 440* Overall height of cavity 455* Minimum inside depth of cavity Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer’s instructions.
- Page 6 PRODUCT DIMENSIONS (OB60B, OB60D MODELS) FRONT SIDE OB60B MODELS OB60D MODELS PRODUCT DIMENSIONS (MM) (MM) Overall height* of product 1077 Overall width of product Overall depth of product (excluding handle and knobs) Height of chassis 1057 Width of chassis Depth of chassis Depth of oven frame and control panel (distance between front of chassis and front of oven door, excluding knobs) Depth of upper oven door when fully open...
- Page 7 CABINETRY DIMENSIONS (OB60B, OB60D MODELS) Electrical supply 16–20 mm min. 1.5 mm SIDE OB60B MODELS OB60D MODELS CABINETRY DIMENSIONS (MM) (MM) Minimum inside width of cavity Overall width of cavity Inside height of cavity 1065 Overall height of cavity 1082 Minimum inside depth of cavity Flush fitting cabinetry clearance...
-
Page 8: Remove The Door
DISCARD PACKAGING RESPONSIBLY IMPORTANT! WARNING! When you remove the oven from the carton be careful not to damage the lower trim. The trim is important for both ventilation and to ensure the door opens fully without obstruction. Very Heavy Do not attempt to lift this product unassisted. - Page 9 CONNECT THE OVEN TO THE MAINS SUPPLY IMPORTANT! This oven must be connected to the mains power supply only by a suitably qualified person. ˜ This oven must be earthed. ˜ Before connecting the oven to the mains power supply, check that the: domestic wiring system is suitable for the power drawn by the oven (as specified on the rating plate) ˜...
- Page 10 SECURE THE OVEN TO THE CABINETRY IMPORTANT! Do not lift the oven by the door handle. ˜ Do not over-tighten the screws. ˜ Do not seal the oven into the cabinetry with silicone or glue. This makes future ˜ servicing difficult. Fisher & Paykel will not cover the cost of removing the oven, or damage caused by this removal.
-
Page 11: Troubleshooting
TROUBLESHOOTING IF THE APPLIANCE IS NOT FUNCTIONING CORRECTLY AFTER INSTALLATION CHECK THE FOLLOWING: That the circuit breaker has not tripped or the fuse blown. Make sure that the electrical connections have been correctly made. Make sure that power is being supplied to the oven. -
Page 12: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER: Make sure the oven is level and securely fitted to the cabinetry and the oven door opens and closes freely. Make sure all the internal packaging has been removed from the oven cavity. ...