Yamaha n8 Service Manual page 81

Item
Executing DICE2-
MUTE ON test
Executing DICE2-
MUTE OFF test
MUTE test (07)
Executing SSP1-
MUTE ON test
Executing SSP1-
MUTE OFF test
Executing HI-Z ON
test
HI-Z test (09)
Executing HI-Z OFF
test
Executing PAD ON
test
Executing PAD OFF
PAD test (08)
test
Executing PAD
ON/OFF test
Executing Phantom
+48 V ON test
Phantom +48 V
test (10)
Executing Phantom
+48 V OFF test
Executing connection
DAW I/O (mLAN)
test
connector
connection test
Results of connection
(11)
test
Changing AD/DA
through connection
AD/DA through
test (12)
Executing Channel
ON/OFF test
Executing calibration
Proceeding to the
next measurement
point
Fader
calibration (13)
Stopping calibration
Completion of
calibration
Deleting calibration
data
Deleting fader
calibration data
Completion of deleting
calibration data
Contents
MUTE is turned on from GPIO.
MUTE is turned off from GPIO.
MUTE is turned on from SSP1.
MUTE is turned off from SSP1.
HI-Z of CH 8 (CH 4 in case of n8) is turned on.
HI-Z of CH 8 (CH 4 in case of n8) is turned off.
PAD of specifi ed channel is turned on.
PAD of specifi ed channel is turned off.
PAD of specifi ed channel is turned on/off.
Phantom +48 V of specifi ed channel is turned on.
Phantom +48 V of specifi ed channel is turned off.
Conducts DAW I/O (mLAN) connector connection test.
Return the results of the DAW I/O (mLAN) connector
connection test.
Switches AD/DA through connection mode.
Specified channel of AD/DA through connection (for
product) is turned on/off.
Changed to fader calibration mode.
Advances measurement point (In case of n8: proceeds in
the order of +6 (db) " -7.5 (db) " -∞ (db). in case of n12:
proceeds in the order of +10 (dB) " 0 (dB) " -15 (dB) " -∞ (dB).
If the switch of the n8 or n12 for stopping the calibration
is pressed, instructions to stop the test will be transmitted
to the personal computer. The test result is judged as NG.
n8 or n12 turns into test command standby condition.
When all the measurement points are measured, the
n8 or n12 transmits ending command to the personal
computer. The test result is judged as OK. n8 or n12
turns into test command standby condition
Deletes fader calibration data on the fl ash ROM.
Indicates completion of deleting fader calibration data.
Direction of transmission
PC " n8 or n12
A0 48 00 F0 43 02 00 01 F7
PC " n8 or n12
A0 48 00 F0 43 02 00 00 F7
PC " n8 or n12
A0 48 00 F0 43 02 01 01 F7
PC " n8 or n12
A0 48 00 F0 43 02 01 00 F7
PC " n8 or n12
A0 49 00 F0 43 02 XX 01 F7
PC " n8 or n12
A0 49 00 F0 43 02 XX 00 F7
PC " n8 or n12
A0 4A 00 F0 43 02 XX 01 F7
PC " n8 or n12
A0 4A 00 F0 43 02 XX 00 F7
PC " n8 or n12
A0 4A 00 F0 43 02 XX XX F7
PC " n8 or n12
A0 4B 00 F0 43 02 XX 01 F7
PC " n8 or n12
A0 4B 00 F0 43 02 XX 00 F7
PC " n8 or n12
A0 4C 00
n8 or n12 " PC
A0 4C XX (XX: 02 → OK, 03 → NG)
A0 4D 00 F0 43 01 XX F7
PC " n8 or n12
(XX: 00 " Normal, 01 " Input test, 02 " Output test)
PC " n8 or n12
A0 4E 00 F0 43 02 XX XX F7
PC " n8 or n12
A0 50 00
PC " n8 or n12
A0 50 01
n8 or n12 " PC
A0 50 03
n8 or n12 " PC
A0 50 02
PC " n8 or n12
A0 50 10
n8 or n12 " PC
A0 50 11
n8/n12
MIDI command
81