Table of Contents
Advertisement
Phone Commands
Panel Function
DISARM
ARM Doors/Windows
ARM Doors/Windows with
No Entry Delay
ARM Motions
ARM Motions with Latchkey
ARM Doors/Windows and
Motions
ARM Doors/Windows with
No Entry Delay and Motions
with Latchkey
Lights On/Off
System Status
Hang Up
If you are interactive with your panel and the panel hangs
up on you, the system is calling in a report to the central
monitoring station or a pager, due to an action made by
you or someone at the security system site.
How to Use Your Touchpads
Touchpads are used to control the security system from
any location within or near your home.
Remote Handheld Touchpad
Interfacing with the system using a Remote Handheld
Touchpad is similar to using the panel.
System Status
Press System Status once to hear
information about your system from
the panel. See "Status Beeps".
ARM Doors & Windows
Press Arm Doors & Windows but-
ton once to turn the security system
protection on for all protected doors
and windows.
Press twice to eliminate the pre-pro-
grammed entry delay.
ARM Motion Sensors
Press Arm Motion Sensors button
once to turn protection on for all
Motion Sensors. Use when no one is home. This is usually
used in combination with ARM Doors & Windows. Press
twice to activate the Latchkey feature.
Note
Depending upon how your dealer programmed your
Phone Command
* + CODE + 1
* + CODE + 2
* + CODE + 2 + 2
* + CODE +3
* + CODE + 3 + 3
* + CODE + 2 + 3
* + CODE + 2 + 2 + 3 +
3
* + CODE + 0
* + CODE + # + 1
* + CODE + 9
SYSTEM
STATUS
ARM
Doors &
Windows
ARM
Motion
Sensors
DISARM
3
1
2
4
5
6
7
8
9
On
Off
EMERGENCY
-
P
re s
s
&
Hol
d
B t o
h
K y
e
s
CODE = any access code
panel, you may be required to enter your access
code to arm the system.
Disarm
Press Disarm button once and enter your access code
using the NUMERIC buttons to turn security protection
off. To subdisarm the system, enter the master access code.
Subdisarm
Enter your access code using the NUMERIC buttons while
the system is disarmed. Panel will announce, system dis-
armed. The Disarm button on the panel will begin to
blink.
Emergency
Press both EMERGENCY buttons for 3 seconds to cause
the system to call a central monitoring station to report a
non-medical emergency.
Keychain Touchpad
If your installer programmed the Key-
chain Touchpad with no entry delay, and
you armed the system with the Keychain
Touchpad, you must disarm your system
before entering the home to avoid caus-
ing an alarm.
If your installer programmed your system
for Remote Touchpad Arming, you must
enter your home to start the entry delay
before you can use your Keychain Touchpad to disarm the
system.
WARNING!
To avoid causing false alarms, check with your
installer on how your touchpad options are pro-
grammed.
LOCK Press once to arm doors and windows.
LOCK Press twice to arm doors, windows, and
Motion Sensors.
LOCK Press 3 times to arm doors, windows,
Motion Sensors, and to activate the Latchkey
option.
LOCK and UNLOCK
Press both buttons simultaneously for 3 sec-
onds to send a panic (intrusion, silent, or
non-medical emergency) alarm to the cen-
tral monitoring station.
Note
Panic alarms need to be silenced from the panel, a
remote handheld touchpad or another keychain
touchpad. They cannot be silenced from the same
keychain that activated the alarm.
UNLOCK Press to disarm your security system.
STAR
Can be programmed to control a device
connected to a unviersal module.
Note
For any keypress on the Keychain Touchpad, hold
the button until the indicator light blinks.
7
Hide quick links:
Advertisement
Table of Contents
