Programming Your System; Programming Instructions - Interlogix Simon 3 User Manual

Programming Your System

The programming decals are visible when you open the
panel cover (see Figure 1.). These decals are designed to
make system programming easier for you. Always begin
by entering your access code. Then, choose an operation
from the START MENU. Follow the voice prompts and
flow arrows to complete the desired task. Notice the button
flow diagrams following the Instruction Summary.

Programming Instructions

Use the following instructions to access the programming
buttons and programming decals.
1. System must be disarmed. Open the Panel Cover by
pressing the plastic latch on the top of the panel.
When you open the cover you will immediately be
prompted by the panel voice to use the numbered keys
to enter your ID.
Version 3
* Press for program
information.
Instruction
Summary
Add Option
Option #1: Panel Beeps
Option #2: Panel Voice
Option #3: Latchkey Time
Option #36: Sensor Activated Light Lockout Start Time
Option #37: Sensor Activated Light Lockout Stop Time
Option #41: Chime Voice
Option #42: Speaker Volume
Option #43: Pager Phone Number
Option #55: Status Beep Volume
Add
Press
2. Enter the Master Access Code.
Note
The Master access code is 1-2-3-4 when the panel is
shipped. You should change your Master Access
Code after your system is installed (see "Access
Code").
3. The system voice will prompt you to begin with the
START MENU.
8
START MENU
Add Delete
MAIN MENU
Light Sensor/
Control Option # Remote
* * *
0
CONTROL MENU
Entry/Exit
Unit # Delay Sensors
* *
4 5
DONE
Add Access Code
Press
use red numbers to enter 4-digit code.
Set Clock
Option #
and follow voice prompts. Press
See Note
1.
Press Down
Doors & Motion
Windows Sensors Status
Arm Disarm System
1 / 2 3 / 4 5 / 6 7 / 8 9 / 0
Special
Doors Motion Time Sensor On
Chime Lights
FIRE POLICE AUX
Test Weekly
Figure 1. Opening the panel cover
Cancel Test
Access Clock
Code Set
1 2 3
Time - Hours +
*
6 7 8 9
Delete
- Minutes +
To delete an option or access code
press
prompting.
Cancel
Add Access Code DONE
If you make a mistake or want to
, then
See Note
start over press
Sensor or Phone Test
Clock Set Hours Minutes DONE
To select a test, press
follow the voice prompting.
See Note
The START MENU includes the following buttons:
Add
Delete
Cancel
Test
Clock Set
Press the appropriate button.
Version 3 START MENU
Add Delete Cancel Test
System should be checked
H O M E S E C U R I T Y by a qualified technician
* Press for program
at least every three years.
information.
MAIN MENU
Light Sensor/ Access Clock
Control Option # Remote Code Set
* * *
C O D E
0 1 2 3
Note:
CONTROL MENU
Entry/Exit
Off Hold key or press
Unit # Delay Sensors Time - Hours +
* * * repeatedly until you
H O M E C O N T R O L
hear the desired item.
4 5 6 7 8 9
Instruction
Delete
- Minutes +
Summary
To delete an option or access code
E M E R G E N C Y
Delete
Add Option press and follow the voice
Option #1: Panel Beeps prompting.
Option #2: Panel Voice DONE
Add Access Code
Option #3: Latchkey Time Cancel
Option #36: Sensor Activated Light Lockout Start Time Add Access Code DONE
If you make a mistake or want to
Option #37: Sensor Activated Light Lockout Stop Time Press , then
Option #41: Chime Voice Cancel
See Note
Option #42: Speaker Volume start over press
use red numbers to enter 4-digit code.
Option #43: Pager Phone Number
Option #55: Status Beep Volume Sensor or Phone Test
Set Clock
Test
Add Option # Clock Set Hours Minutes DONE
To select a test, press and
Press and follow voice prompts. Press
follow the voice prompting.
See Note See Note
System should be checked
by a qualified technician
at least every three years.
Note:
Hold key or press
repeatedly until you
hear the desired item.
Delete
and follow the voice
Cancel
Test
and
2.
Open
Cover