Table of Contents
Advertisement
4.
The panel voice prompts you to Select from MAIN
MENU. Press the Light Control button on the
MAIN MENU.
5.
The panel voice responds with House Code is *, press
again to change or press unit number. This is the
House Code that was set by your installer. Don't
change it. Press the Unit # button.
6.
The panel responds with Unit #1 press again to
change or select from control menu. Keep pressing the
Unit # button until the correct unit is selected.
7.
Press the Time button on the control menu. The panel
voice prompts you, On time is **** to change press
hours and minutes then press done.
8.
Press the Hours and Minutes buttons to set the cor-
rect on time.
9.
Press Done. Panel will announce, Off time is **** to
change press hours and minutes then press done.
10. Press the Hours and Minutes buttons to set the cor-
rect off time.
11. Press Done. Panel will announce the unit number with
the on and off times you just programmed.
Programming Options
The following table is a list of options you can change.
Programming Options
Option #
01 - Panel Beeps
02 - Panel Voice
03 - Latchkey Time
36 - Sensor Activated Light
Lockout Start Time
37 - Sensor Activated Light
Lockout Stop Time
41 - Chime Voice
42 - Speaker Volume
43 - Pager Phone Number
55 - Status Beep Volume
* See "Option 43 - Pager Phone Number"
Press Add in the START MENU and follow the voice
prompts to turn an option on.
Press Delete in the START MENU to turn an option off.
10
Add
Delete
On
Off
On
Off
12:00 am
Off
(midnight) to
11:59 pm
12:00 am
Off
(midnight) to
11:59 pm
12:00 am
Off
(midnight) to
11:59 pm
On
Off
1 - 8
8
(highest)
Up to 26
Off
digits*
1 - 10
7
When entering a single digit option number (1-9), you
must type a zero before the number (i.e. 01, 02, .....). All
option numbers must be 2 digits.
Option 01 - Status Beeps
Add this option to enable panel beeps. Status beeps are any
beeps (including chime beeps) that come from the panel.
See "Status Beeps".
1.
Open panel cover. Panel announces, Use numbered
keys to enter ID.
2.
Enter Access Code using the numbered keys. Panel
announces, Please select from Start Menu.
3.
Press Add from the Start menu. Panel announces,
Select from main menu.
4.
Press Option #. Panel announces, Option 1, press
again for next option or done to select
5.
Press DONE. Panel announces, Option 1 is on.
Delete turns off panel piezo beeps.
1.
Open panel cover. Panel announces, Use numbered
keys to enter ID.
2.
Enter Access Code using the numbered keys. Panel
announces, Please select from Start Menu.
3.
Press Delete from the Start menu. Panel announces,
Select from main menu.
4.
Press Option #. Panel announces, Option 1, press
again for next option or done to select.
5.
Press DONE. Panel announces, Option 1 deleted.
Option 02 - Panel Voice
Panel Voice may be disabled, except for status messages,
open sensor responses, and when in program mode.
Add enables the panel voice.
1.
Open panel cover. Panel announces, Use numbered
keys to enter ID.
2.
Enter Access Code using the numbered keys. Panel
announces, Please select from Start Menu.
3.
Press Add from the Start menu. Panel announces,
Select from main menu
4.
Press Option #. Panel announces, Option 1, press
again for next option or done to select.
5.
Press 02. Panel announces, Option 2, press again for
next option or done to select
6.
Press DONE. Panel announces, Option 2 is on.
Delete disables the panel voice.
1.
Open panel cover. Panel announces, Use numbered
keys to enter ID.
2.
Enter Access Code using the numbered keys. Panel
announces, Please select from Start Menu.
3.
Press Delete from the Start menu. Panel announces,
Select from main menu
Hide quick links:
Advertisement
Table of Contents
