Advertisement
Quick Links
BELT SANDER – 3" x 18"
Model 40118
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
®
Copyright
by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Advertisement
Related Manuals for Chicago Electric 40118
Summary of Contents for Chicago Electric 40118
- Page 1 BELT SANDER – 3” x 18” Model 40118 ASSEMBLY AND OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com ® Copyright by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
-
Page 2: Sanding Belt
USE EYE AND BREATHING PROTECTION. Wear ANSI approved safety impact eye goggles and a NIOSH (National Institute for Occupational Safety and Health) approved respirator. ANSI approved safety impact eye goggles, dust masks, and respirators are available from Harbor Freight Tools. SKU 40118 PAGE 2... - Page 3 WARNING: The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors, which cannot be built into this product, but must be supplied by the operator. SKU 40118 PAGE 3...
- Page 4 NEVER STAND OR HAVE AN OBSERVER STAND IN LINE WITH THE ROTAT- ING SANDING BELT (part #2). (See Figure C.) USE THE PROPER SIZE AND TYPE OF SANDING BELT (3” WIDE BY 18” Length). (See Figures B, and C.) SKU 40118 PAGE 4...
- Page 5 When unpacking, check to make sure all the parts shown on the Parts List on page 10 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SKU 40118 PAGE 5...
-
Page 6: Front Wheel Frame
(part #21) all the way to the right to release tension on the Sanding Belt (part #2). Then, pull the Sanding Belt off the Front Wheel Frame (part #5) and Rear Wheel (part #8). (See Figure B.) SKU 40118 PAGE 6... -
Page 7: Rear Wheel
Switch Lock. Then, release pressure on the Power Switch. The Power Switch will now be locked in its “ON” position. To return to manually operating the Belt Sander, simply squeeze the Power Switch again to unlock the Switch Lock. (See Figures C, and D.) SKU 40118 PAGE 7... -
Page 8: Belt Release Lever
Sanding Belt has stopped rotating. Then, unplug the Belt Sander from its electri- cal outlet. Move the Belt Release Lever (part #21) all the way to the right, and properly reposition the Sanding Belt. Next, move the Belt Release Lever all the SKU 40118 PAGE 8... -
Page 9: Power Switch
CIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 40118 PAGE 9... -
Page 10: Table Of Contents
Carbon Brush Spring Bearing Carbon Brush Screw Bearing Small Belt Wheel Bearing Brush Belt Belt Release Lever Big Belt Wheel Hatch Ring Belt Cover Switch Lock Screw Power Switch Plate Capacitor Cord Cover Screw Power Cord SKU 40118 PAGE 10... - Page 11 ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 40118 PAGE 11...