SaVE ThIS MaNUaL CaUTION, used with the safety Keep this manual for the safety alert symbol, indicates a warnings and precautions, assembly, hazardous situation which, if operating, inspection, maintenance and not avoided, could result in cleaning procedures. Write the product’s minor or moderate injury.
Page 3
Electrical safety moment of inattention while operating power tools may result in serious Power tool Plugs must match the personal injury. outlet. Never modify the Plug in any way. do not use any adapter Use personal protective plugs with grounded power tools. equipment.
and off. Any power tool that cannot only identical replacement parts. be controlled with the Switch is This will ensure that the safety of the dangerous and must be repaired. power tool is maintained. disconnect the Power Cord from Specific Safety Warnings the power source before making any adjustments, changing Maintain labels and nameplates on...
• Do not use with power switch locked cover all possible conditions and situations that may occur. It must • Properly maintain and inspect to be understood by the operator that avoid electrical shock. common sense and caution are • Any power cord must be properly factors which cannot be built into this grounded.
Include vibration-free periods each double Insulated Tools: Tools day of work. with Two Prong Plugs Grip the power tool as lightly as possible (while still keeping safe control of it). Let the tool do the work. To reduce vibration, maintain the power tool as explained in this manual.
The smaller the gauge number of the Symbology wire, the greater the capacity of the cord. For example, a 14 gauge cord Double Insulated can carry a higher current than a 16 gauge cord. (See Table a.) Canadian Standards Association When using more than one extension Underwriters Laboratories, Inc.
refer to the Assembly Diagram near COMPONENTS the end of this manual. Power Switch (44) Turn the Power Switch off and unplug the tool. Spindle (5) Tool attachment Figure b [angled Angled Scraper (4) Sanding Scraper (4)] (502) Spindle Angled Cutter Blade (501) Half Moon Cutter Blade (503) Sanding...
Page 9
be mounted at angles up to 90° left or Torque to 10 ft-lbs right. Angled Cutter Blade (501) Figure d Note: The long Angled Cutter Blade (501) should only be used in the straight Figure F ahead position. (See Figure d.) Tighten the cap screw onto the Spindle using the provided hex key.
Avoid contact with foreign objects OPERaTINg INSTRUCTIONS such as metal screws and nails when Read the ENTIRE IMPORTaNT sanding, scraping, or cutting. SaFETY INFORMaTION Do not apply excessive pressure section at the beginning of this on the tool. Allow the tool to do the manual including all text under work.
If you notice decreased performance, MaINTENaNCE aNd have the unit serviced and Carbon SERVICINg Brushes (40) replaced by a qualified technician. Procedures not specifically explained in this manual WaRNINg! If the Power Cord must be performed only by a (46) of this Tool is damaged, qualified technician.
Troubleshooting Problem Possible Causes Likely Solutions Tool will not start. Cord not connected. Check that cord is plugged in. No power at outlet. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads.
PaRTS LIST aNd aSSEMbLY dIagRaM Part description Part description Cap Screw (M8 x 1.25 x 12) Stator Small Washer Plastic Housing Large Washer Link Pole Angled Scraper Cord Clip Spindle Screw (ST4.0 x 14) Rubber Casing Pull Brace Circlip for Shaft 26 Spline Spring Washer Brush Holder Bearing (6000)
Record Product’s Serial Number either repair or replace the product at our here: election or we may elect to refund the purchase price if we cannot readily and Note: If product has no serial number, quickly provide you with a replacement. We record month and year of purchase will return repaired products at our expense, instead.