Chicago Electric 90045 Set Up And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Chicago Electric Manuals
  4. Sander
  5. 90045
  6. Set up and operating instructions manual

Chicago Electric 90045 Set Up And Operating Instructions Manual

3” x 21” belt sander
Hide thumbs Also See for 90045:
Table of Contents

Advertisement

Quick Links

Set up and Operating inStructiOnS
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS Manual.
©
Copyright
2003 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual revised 10e

Belt Sander

3" x 21"
Model
®
. All rights reserved. No portion of this manual or any artwork
90045

Advertisement

Table of Contents
loading

Related Manuals for Chicago Electric 90045

Summary of Contents for Chicago Electric 90045

  • Page 1: Belt Sander

    Belt Sander 3” x 21” Model 90045 Set up and Operating inStructiOnS Visit our website at: http://www.harborfreight.com read this material before using this product. Failure to do so can result in serious injury. SaVe thiS Manual. © ® Copyright 2003 by Harbor Freight Tools .

  • Page 2: Table Of Contents

    Operating inStructiOnS ..10 cOntentS tOOl Set up ........10 iMpOrtant SaFetY wOrk piece and wOrk area inFOrMatiOn .........3 Set up ..........10 general pOwer tOOl SaFetY general Operating warningS ........... 3 inStructiOnS ......... 10 Belt Sander SaFetY warningS ..5 Maintenance and SerVicing ...12 ViBratiOn SaFetY ......

  • Page 3: Important Safety Information

    nOtice is used to SaVe thiS Manual address practices not Keep this manual for the safety warnings related to personal injury. and precautions, assembly, operating, cautiOn, without the inspection, maintenance and cleaning safety alert symbol, is procedures. Write the product’s serial number used to address practices not in the back of the manual near the assembly related to personal injury.
  • Page 4 increased risk of electric shock if your finger on the switch or energizing power body is grounded. tools that have the switch on invites accidents. do not expose power tools to rain or wet conditions. Water entering remove any adjusting key or wrench a power tool will increase the risk of before turning the power tool on.

  • Page 5: Belt Sander Safety Warnings

    disconnect the plug from the Belt Sander Safety warnings power source before making any hold power tools by insulated adjustments, changing accessories, gripping surfaces when performing or storing power tools. Such an operation where the cutting tool preventive safety measures reduce may contact hidden wiring or its own the risk of starting the power tool cord.

  • Page 6: Vibration Safety

    Interrupter (GFCI) should also be cause temporary or permanent physical implemented – it prevents sustained injury, particularly to the hands, arms electrical shock. and shoulders. To reduce the risk of vibration-related injury: WARNING: Some dust created by power sanding, sawing, grinding, drilling, and Anyone using vibrating tools regularly other construction activities, contains or for an extended period should first...

  • Page 7: Grounding

    preceding illustration. (See Outlets for grOunding 2-Prong Plug.) tO preVent extension cords electric ShOck and death FrOM incOrrect Grounded tools require a three wire grOunding wire extension cord. Double Insulated cOnnectiOn: tools can use either a two or three wire Check with a qualified electrician extension cord.

  • Page 8: Symbology

    Protect the extension cords from sharp objects, excessive heat, and damp or wet areas. recOMMended MiniMuM wire gauge FOr extenSiOn cOrdS* (120/240 VOlt) extenSiOn cOrd naMeplate length aMpereS (at full load) 0 – 2.0 2.1 – 3.4 3.5 – 5.0 5.1 –...

  • Page 9: Specifications

    SpeciFicatiOnS to remove/install a Sanding Belt: trigger Electrical Input 120 V~ / 60 Hz / 7.5 A (Rated) (66) Belt Speed 1,250 FPM (No Load) Sanding Belt (46) Belt Size 3” x 21” Accessories Dust Bag / 120 Grit Belt e194601 tenSiOn leVer OF Figure a...

  • Page 10: To Attach The Dust Bag

    off the Belt Sander. release the Trigger once. (See Figures a and B.) (See Figure B.) WARNING! Prior to using the Belt to attach the dust Bag: Sander (each time), make sure the Switch Lock mechanism is working properly. Release the Switch Lock mechanism before disconnecting the Belt Sander from its electrical outlet.
  • Page 11 warning! when sanding a workpiece, always push and pull the Belt Sander over the workpiece with both hands firmly gripping the tool. Do not pass hands or fingers directly in front of, to the rear, or below the Sanding Belt (46). Firmly grip the Belt Sander with both hands.

  • Page 12: Maintenance And Servicing

    Maintenance and CARBON BRUSH: To maintain peak efficiency of the Belt Sander’s Motor SerVicing it is recommended that every two to six months the Carbon Brush (27) be Procedures not specifically examined. explained in this manual must be performed only by a qualified BruSh technician.

  • Page 13: Troubleshooting

    troubleshooting problem possible causes likely Solutions Tool will not start. Cord not connected. Check that cord is plugged in. No power at outlet. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads.

  • Page 14: Parts List

    pleaSe read the FOllOwing careFullY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROvIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAkES ANy REPRESENTATION OR WARRANTy OF ANy kIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAkE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT.

  • Page 15: Assembly Diagram

    aSSeMBlY diagraM reV 04l, 10e SKU 90045 For technical questions, please call 1-800-444-3353. Page 15...

  • Page 16: Limited 1 Year / 90 Day Warranty

    To take advantage of this warranty, liMited 1 Year / 90 daY the product or part must be returned to us warrantY with transportation charges prepaid. Proof of purchase date and an explanation of the Harbor Freight Tools Co. makes every complaint must accompany the merchandise.

Table of Contents