Table of Contents
Advertisement
Save This Manual
For Future Reference
ISears
NODEL NO.
113.249070
Serial
Number .........................................
Model and serial
number
may be found
at the right-hand
side of
the platform
channel.
You should
record both
model and serial number
in asafe place for
future use.
CAUTIO
.-
Read GENERAL and
ADDITIONAL SAFETY
INSTRUCTIONS
carefully.
Copy-Crafter
accessory
is for 12 inch
Craftsman
wood lathes
with tubular
bed
only. It is shown
mounted
on a Craftsman
Workbench
and Lathe.
,, assembly
,, operating
o repair parts
Sold by SEARS, ROEBUCK
AND CO., Chicago,
IL. 60684 U.S.A.
Part No. 70041
Prin'_ed i_ U_S_
Advertisement
Table of Contents
Related Manuals for Craftsman 113.24907
Summary of Contents for Craftsman 113.24907
- Page 1 CAUTIO Read GENERAL and ADDITIONAL SAFETY INSTRUCTIONS carefully. Sold by SEARS, ROEBUCK Part No. 70041 Copy-Crafter Craftsman only. It is shown Workbench ,, assembly ,, operating o repair parts AND CO., Chicago,...
-
Page 2: General Safety Instructions
It will do the job better and safer at the rate for which it was designed. ON CRAFTSMAN THE UNITED STATES. AND CO., Dept. 698/731A, Sears Tower, Chicago, read and understand warnings. which follow appJy to your Lathe and Copy-Crafter... - Page 3 Iocknuts before operating. the instructions found label which appears on the channel. !111 I1'1'11 of any power tool can result Always wear before commencing power Safety Goggles are available at Sears tool...
-
Page 4: Table Of Contents
Pliers The Copy-Crafter is shipped unassembled order tofacilitate packaging, The step by step that fo low explain how to assembte the Copy-crafter how tomake a project, Before starting assemble Copy-Crafter, read this entire manual first to become the namer; and location of the various function. - Page 5 assembly BED ASSEMBLY Copy-C;rafter is made up of held together by T{e Rods. (3) three same except has the Copy-Crafter Front Channel, The other (2) two are Vertical Assemble the Front Channel and (I) Channels as shown using (2) two Round Bolts 3/4 inches long and (2) Flange...
-
Page 6: Copy-Crafter
MOUNTING COPY-CRAFTER BED TO BENCH • Remove _he Too Rest Base and lock ng hardwarefrom the Lathe (see your Lathe Owners Tailstock appr0ximateiy HeadstoCk: • • NOTE: If" your Lathe has a Tool i0cking harclware like the one shown in this illustration be sure to unscrew the Threaded... -
Page 7: Assembly
assembly Front Charmer should be slightly of the Vertical Channels. Check combination square as shown. If it is higher, Flange Nuts and lower it. TOOL HOLDER Screw a 1-3/4 inch tong socket head screw tightly each Knob as shown. Screw a Square Nut onto each of the Follower NOTE:... - Page 8 3_:::_re_::_he Khobs:and FOilbwer Pins:into the Tool:Post : 6i :An:k!;gnmen_ Gauge is provided to align the tip of the Cutting tliel €_nteriine page:11i number e); The fotiowing Steps explain how Nut t0 the: p0irit of the spur: Center as shown, IIIIIIIII [I IIIIIIIIHIII iiiili bi: Using a sharp pointed instrument;: scratch a mark...
-
Page 9: Brackets
assembgy Remove protective coat{ng from Cutting Tool and place it in the Cradle, Insert Cutting Too} and Cradle Post and rotate it back and forth Screw the Too_ Screw should seat into cove Cutting Tool. Hold Al;gnment Gauge tightly against ...make sure it is resting on top of Square... - Page 10 CUTTING TOOL CONTROL TOOL POST KNOBS BASE BRACKETS FOLLOWER 2. VERTICAL CHANNELS FRONT CHANNEL CENTER SCREW 1. FRONT CHANNEL...comfortably hands while maneuvering the Cutting Tool. VERTICAL CHANNELS...support and the Brackets. BRACKETS...hold the template or an existing turning. 4. TOOL POST BASE...supports contains the control Knobs and the Follower Pins_ CRADLE PINS...
-
Page 11: Getting To Know Your Copy-Crafter
getting to know your copy-crafter CONTROL KNOBS...provide a comfortable maneuvering the Cutting Toot. They holes in the end of the Tool Post for spindle turnings and: into opposite duplicating faceplate turnings. TOOL POST...supports Cutting Cutting Toot Cradle. It can be swiveled left for various types of cuts. -
Page 12: Clamp
11_CLAMP PLATE...holds the Lathe Tool Rest to the Vertical Channels for rough turning to the general sha oe and cleaning up sharp corners on the finished turnings. The toot Rest should be set approximately below the Centerline Of the Lathe and approximately 1/8 inch away from the workoiece. - Page 13 getting to know your copy-crafter 12. SHARPENING STONE...is provided sharpening of the Cutting Tool WHEN TOOL 1S SHARP, HALF DONE, Apply a generous amount light use motor 0il) the stone, motion hone the entire rounded edge of the toot while holding it firmly.
-
Page 14: Operation
slots I80 ° apart screwdriver_ This will allow you to hold the Faceplate while unscrewing the workpiece. Attach the Backing to the Faceptate #14x3/4 inca flathead wood screws. TUrn the backing round and true up the face so that it is approximately 1/32 inch low in the center. - Page 15 SOUND BLOCK SOUND BLOCK CENTER LINE 1-3/4" "I 1 !132 13-114" CENTER LINE HANDLE CUT WITH SCISSORS ALONG DOTTED LINES Ill-_ _CENTER !1t32" ] \',_,.. jJ ,,,,,,,,,,,,,_,,J , ,,,,,,,, ,J ., 2-1/2" -- 1-*--_ 2-314" m_mm_mmwm/m z-1/4" LIN_ "_ GAVEL HEAD 2-tt2"...
-
Page 17: Duplicating Froma Template
operation DUPLICATING FROM A TEMPLATE Here are instructions for two simpfe projects familarize you with making templates, and then duplicating from them. STARTER PROJECT: GAVEL AND SOUND BLOCK Remove page from this manual scissors along dotted lines. NOTE: The pattern the handle overall length... - Page 18 : : Maneuve_ the cutting T0oi b_ moving your wrists while the Of Your hands _he::Front /sides light CUts t6 _tar_ With,_ ohtii YOU get the feel Of the cutt ng :action_: :the cutting T001 _houlcl bedown h th e narrow diamete_ ! i ...
- Page 19 operation 11 _ Turn down both ends to about 12. Smooth up with sandpaper, 13. Remove the workpiece from the Lathe off. Sand smooth. 14. Select a piece of wood 1-1/4 inches _nches long for the handle of the gavel. NOTE: When turning small diameters,...
- Page 20 operaUon Attach Tool Rest (See@ page 11) workpiece to 4-1/2 inches in diameter. Rotate Tool Post 180 degrees and realign Tool with the short Follower Pin...screw opposite holes for operation. NOTE: When turning facep]ates, do not move Tool to _he right Of the centerline 0f:the Attach Tool...
-
Page 21: Duplicating Aspindle
operation 10, Insert a screwdriver into one of the slots in the backing prevent from turning while workpiece. ! 1. Glue a piece of felt to the bottom the furniture surface, DUPLICATING SPINDLE EXISTING Two Spindle Brackets are provided for duplicating an existing spindle. - Page 22 operation POINT CUP CENTER turn the Tailstock to the right-hand side of the Lathe bed and replace the: left T_e Rod. Attach a Spindle Bracket to tbe right-hand BraCket: With the C_amp P ate align the _'ight-bend cone-Point Set Screw with the or a piece of plyWood across the Vertical Channels, point in the Cup center asshown.
- Page 23 CONTOUR GAUGE Use Sears Contour Gauge 9-3946 to obtain the outline of the existing spindfe for the template,...
-
Page 24: Repair Parts
repair parts PARTS LIST FOR CRAFTSMAN COPY CRAFTER MODEL 113.249070 s._. Figure 1... -
Page 25: Post, Tool
repair parts PARTS LIST FOR CRAFTSMAN Always Order by Part Number -- Not Key Number COPY.CRAFTER MODEL 113.249070 FIGURE I Description Part No. Tool, Cutting 70036 Cradle 70035 *Screw, Socket Set 5tl 6-18x112 STD503105 Post, Tool 70027 Pin, Fo;lower 2-3t8 70038 Pin, Follower 1-It2... - Page 26 LIST OF PARTS LOOSE PARTS Loose Parts Bag #70028 _BContaining the following parts:l racket, Right Template Rod. 5/16-18 Tie ... Bracket. Left Tern plate Bracket. Spindle Mounting Clamp Wrench Post, Tool Knob Tool, Cutting Gage, Tool Loose Parts Bag _f70034 (Containing the following parts:)
- Page 28 PART DESCRIPTION MODEL NUMBER NAME OF ITEM 113.249070 Copy-Crafter All parts Iisted may be ordered from any Sears Service Center and most Sears stores. If the parts you need are not stocked loca!ly, your order will be electronically Repair Parts Distribution...