DISASSEMBLY PROCEDURES (分解手順) ........10 CIRCUIT BOARDS (シート基板図) ..........29 TEST PROGRAM (テストプログラム) ..........41 INSPECTIONS (検査) ..............51 UPDATING (アップデート) .............. 66 PARTS LIST BLOCK DIAGRAM (ブロック図) OVERALL CIRCUIT DIAGRAM (総回路図) 012000 HAMAMATSU, JAPAN Copyright (c) Yamaha Corporation. All rights reserved. YMW ´10.09...
Page 2
IMPORTANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have there- fore not been restated.
DSR112/DSR115/DSR215/DSR118W ■ DISASSEMBLY PROCEDURES (分解手順) Disassembly of DSR112 DSR112 の分解 Metal Grille Assembly メタルグリル Ass'y (Time required: About 1 minute) (所要時間:約 1 分) 1-1. Remove the eight (8) screws marked [180]. The metal grille 1-1. [180]のネジ 8 本を外して、メタルグリル Ass'y を外...
Page 11
DSR112/DSR115/DSR215/DSR118W Horn Assembly ホーン Ass'y (Time required: About 3 minutes) (所要時間:約 3 分) 3-1. Remove the front grille assembly. (See procedure 1) 3-1. メタルグリル Ass'y を外します。 (1 項参照) 3-2. Remove the eight (8) screws marked [40b]. (Fig. 4, 5) 3-2.
Page 12
DSR112/DSR115/DSR215/DSR118W 3-5. Horn 3-5. ホーン 3-5-1 Remove the two (2) hexagonal head bolt marked [A]. 3-5-1 [A]の六角ボルト 2 本を外して、 ホーンとスピーカー (Fig. 6) に別けます。 (図 6) The horn and the speaker can then be separated. (Fig. 6) 3-6. Diaphragm Assembly 3-6.
Page 13
DSR112/DSR115/DSR215/DSR118W LED Circuit Board LED シート (Time required: About 2 minutes) (所要時間:約 2 分) 4-1. Remove the metal grille assembly. (See procedure 1) 4-1. メタルグリル Ass'y を外します。 (1 項参照) 4-2. Remove the two (2) screws marked [310]. The LED panel 4-2.
Page 14
DSR112/DSR115/DSR215/DSR118W Disassembly of DSR115 DSR115 の分解 Metal Grille Assembly メタルグリル Ass'y (Time required: About 1 minute) (所要時間:約 1 分) 1-1. Remove the eight (8) screws marked [180]. The metal grille 1-1. [180]のネジ 8 本を外して、メタルグリル Ass'y を外 assembly can then be removed. (Fig. 1) します。...
Page 15
DSR112/DSR115/DSR215/DSR118W Horn Assembly ホーン Ass'y (Time required: About 3 minutes) (所要時間:約 3 分) 3-1. Remove the front grille assembly. (See procedure 1) 3-1. メタルグリル Ass’y を外します。 (1 項参照) 3-2. Remove the eight (8) screws marked [40b]. (Fig. 4, 5) 3-2.
Page 16
DSR112/DSR115/DSR215/DSR118W 3-5. Horn 3-5. ホーン 3-5-1 Remove the two (2) hexagonal head bolt marked [A]. 3-5-1 [A]の六角ボルト 2 本を外して、 ホーンとスピーカー (Fig. 6) に別けます。 (図 6) The horn and the speaker can then be separated. (Fig. 6) 3-6. Diaphragm Assembly 3-6.
Page 17
DSR112/DSR115/DSR215/DSR118W LED Circuit Board LED シート (Time required: About 2 minutes) (所要時間:約 2 分) 4-1. Remove the metal grille assembly. (See procedure 1) 4-1. メタルグリル Ass'y を外します。 (1 項参照) 4-2. Remove the two (2) screws marked [320]. The LED panel 4-2.
Page 18
DSR112/DSR115/DSR215/DSR118W Disassembly of DSR215 DSR215 の分解 Metal Grille Assembly メタルグリル Ass'y (Time required: About 1 minute) (所要時間:約 1 分) 1-1. Remove the eight (8) screws marked [180]. The metal grille 1-1. [180]のネジ 8 本を外して、メタルグリル Ass'y を外 assembly can then be removed. (Fig. 1) します。...
Page 19
DSR112/DSR115/DSR215/DSR118W Horn Assembly ホーン Ass'y (Time required: About 3 minutes) (所要時間:約 3 分) 3-1. Remove the front grille assembly. (See procedure 1) 3-1. メタルグリル Ass'y を外します。 (1 項参照) 3-2. Remove the eight (8) screws marked [40b]. (Fig. 4, 5) 3-2.
Page 20
DSR112/DSR115/DSR215/DSR118W 3-5. Horn 3-5. ホーン 3-5-1 Remove the two (2) hexagonal head bolt marked [A]. 3-5-1 [A]の六角ボルト 2 本を外して、 ホーンとスピーカー The horn and the speaker can then be separated. (Fig. 6) に別けます。 (図 6) 3-6. Diaphragm Assembly 3-6. ダイヤフラム Ass'y 3-6-1 Remove the three (3) screw marked [B], and remove the 3-6-1 [B]のネジ...
Page 21
DSR112/DSR115/DSR215/DSR118W LED Circuit Board LED シート (Time required: About 2 minutes) (所要時間:約 2 分) 4-1. Remove the metal grille assembly. (See procedure 1) 4-1. メタルグリル Ass'y を外します。 (1 項参照) 4-2. Remove the two (2) screws marked [300]. The LED panel 4-2.
Page 22
DSR112/DSR115/DSR215/DSR118W Disassembly of DSR118W DSR118W の分解 Metal Grille Assembly メタルグリル Ass'y (Time required: About 1 minute) (所要時間:約 1 分) 1-1. Remove the eight (8) screws marked [150]. The metal grille 1-1. [150]のネジ 8 本を外して、メタルグリル Ass'y を外 assembly can then be removed. (Fig. 1) します。...
Page 23
DSR112/DSR115/DSR215/DSR118W LED Circuit Board LED シート (Time required: About 2 minutes) (所要時間:約 2 分) 3-1. Remove the metal grille assembly. (See procedure 1) 3-1. メタルグリル Ass'y を外します。 (1 項参照) 3-2. Remove the two (2) screws marked [280]. The LED panel 3-2.
Page 24
DSR112/DSR115/DSR215/DSR118W Amp Assembly 118 アンプ Ass'y 118 (Time required: About 2 minutes) (所要時間:各約 2 分) 4-1. Remove the ten (10) screws marked [100]. The amp 4-1. [100]のネジ 10 本を外して、アンプ Ass'y 118 を外し assembly 118 can then be removed. (Fig. 4) ます。...
Page 25
DSR112/DSR115/DSR215/DSR118W Disassembly of Amp Assembly アンプ Ass'y の分解 The disassembly procedure of amp assembly 112 is explained as a 代表としてアンプ Ass'y 112 の分解手順を説明します。 representative. アンプ Ass'y 115、215、118 は同様の方法で分解することが The amp assembly 115, 215 and 118 can be disassembled in the できます。...
Page 27
2-3. [130]のネジ 6 本を外して、DSP(DSR112/115/215) 2-3. Remove the six (6) screws marked [130]. The DSP または ASP(DSR118W)シートを外します。 (図 2) (DSR112/115/215) or ASP (DSR118W) circuit board can then be removed. (Fig. 2) IN3 Circuit Board IN3 シート (Time required: About 4 minutes) (所要時間:約...
Page 30
DSR112/DSR115/DSR215/DSR118W • AC IN Circuit Board to AMPS1 to Power Switch AC IN CN101 Component side (部品側) Pattern side (パターン側) 2NA-WT87160...
Page 31
DSR112/DSR115/DSR215/DSR118W • ASP Circuit Board to IN4 CN202 Component side (部品側) to BRG4 to BRG4 CN901 CN902 Pattern side (パターン側) 2NA-WT87410...
Page 32
DSR112/DSR115/DSR215/DSR118W • AMPS1/AMPS2 Circuit Board to AC IN Component side (部品側) 2NA-WT87350...
Page 33
DSR112/DSR115/DSR215/DSR118W • AMPS1/AMPS2 Circuit Board to Woofer to Tweeter (DSR112/DSR115/DSR215) Component side (部品側) 2NA-WT87350...
Page 36
DSR112/DSR115/DSR215/DSR118W • BRG1/BRG2/BRG3 Circuit Board to AMPS1 CN701 to DSP to DSP to AMPS1 CN104 CN103 CN702 Component side (部品側) Pattern side (パターン側) 2NA-WT87300 • LED Circuit Board Component side (部品側) Pattern side (パターン側) 2NA-WT87150...
Page 37
DSR112/DSR115/DSR215/DSR118W • BRG4 Circuit Board Reduction : 3/4 to AMPS2 CN701 to ASP to ASP to AMPS2 CN302 CN303 CN702 Component side (部品側) Pattern side (パターン側) 2NA-WT87330...
Page 38
DSR112/DSR115/DSR215/DSR118W • DSP Circuit Board to IN1/IN2/IN3 CN803 to IN1/IN2/IN3 CN804 Component side (部品側) to BRG1/BRG2/BRG3 to BRG1/BRG2/BRG3 CN902 CN901 Pattern side (パターン側) 2NA-WT87140...
Page 39
DSR112/DSR115/DSR215/DSR118W • IN1/IN2/IN3 Circuit Board to DSP CN102 to DSP CN101 Component side (部品側) Component side (部品側) Pattern side (パターン側) Pattern side (パターン側) 2NA-WT87300...
Page 40
DSR112/DSR115/DSR215/DSR118W • IN4 Circuit Board to ASP CN301 Component side (部品側) Component side (部品側) Pattern side (パターン側) Pattern side (パターン側) 2NA-WT87330...
DSR112/DSR115/DSR215/DSR118W ■ TEST PROGRAM (テストプログラム) This test program is applied to the DSR112, DSR115 and DSR215. このテストプログラムは DSR112、DSR115、DSR215 に適 用されます。 Preparation 準備 1-1. Required items 1-1. 必要なもの • Personal Computer; DOS/V machine (Pentium 500 • パソコン DOS/V 機(Pentium 500 MHz 以上、RAM MHz or faster, RAM 256MB or above, Windows XP 256MB 以上、Windows XP、COM ポート有り)...
Page 42
DSR112/DSR115/DSR215/DSR118W Service inspection サービス検査 2-1. How to activate 2-1. 起動方法 (1) With the FRONT LED DISABLE switch turned off (1) FRONT LED DISABLE スイッチをオフにした (ス (switch is not pressed inward), turn on the power to the イッチを押さない)状態で AMP UNIT の電源を...
Page 43
DSR112/DSR115/DSR215/DSR118W Test Items 検査項目 For details of inspection refer to “INSPECTIONS” on page 検査の詳細は 「検査」 ( 51 ページ) を参照してください。 3-1. INFO inspection 3-1. INFO 検査 This inspection must be performed first. If this ※ この検査は最初に実施してください。 inspection is performed after the CALIBRATION CALIBRATION 調整検査後にこの検査を実施し...
Page 44
DSR112/DSR115/DSR215/DSR118W (2) Execute calibration using “+0.1” and “-0.1” buttons so (2) HF SP OUT(CN500)の出力レベルが 43 ページ that output level of HF SP OUT (CN500) is within the の基準値におさまるように、 「+0.1」 「-0.1」ボタ criterion shown on page 43. ンで校正します。 When “ENTER” is clicked, the corrected value is 「ENTER」...
Page 45
DSR112/DSR115/DSR215/DSR118W The result is displayed in output window as shown 検査結果はアウトプットウインドウへ下記のよ below. うに表示されます。 When OK OK の場合 DAC-HF CALIBRATION OK: CALIBRATION DAC-HF DAC-HF CALIBRATION OK: CALIBRATION DAC-HF DAC-LF CALIBRATION OK: CALIBRATION DAC-LF DAC-LF CALIBRATION OK: CALIBRATION DAC-LF DAC-HF DATA WRITE...
Page 46
DSR112/DSR115/DSR215/DSR118W 3-5. SWITCH inspection 3-5. SWITCH 検査 Inspect on/off status of FRONT LED DISABLE, HPF, and FRONT LED DISABLE、HPF、D-CONTOUR 各スイッ D-CONTOUR switches. チの ON/OFF 状態を検査します。 Set each switch to ON or OFF position according to the 画面表示に従って各 SW を ON または OFF に設定し、...
Page 47
DSR112/DSR115/DSR215/DSR118W 3-6. DSP inspection 3-6. DSP 検査 Communication condition with DSP via I2C-BUS and I2C-BUS 経由の DSP との通信状態、DSP 内部の動作 operational state of inside DSP are inspected automatically. 状態の良否を自動的に検査します。 The result is displayed in output window as shown below. 検査結果はアウトプットウインドウへ下記のように 表示されます。...
Page 48
DSR112/DSR115/DSR215/DSR118W 3-8. D-MUTE inspection 3-8. D-MUTE 検査 Inspect the output level when digital mute. デジタルミュート時の出力レベルを検査します。 Input the 1 kHz, 0 dBu sine wave between 7 pin (SIG-) and 1 kHz、0 dBu 正弦波を DSP シートの CN101 の 7 ピン 8 pin (SIG+) of CN101 on the DSP circuit board.
Page 49
DSR112/DSR115/DSR215/DSR118W The explanation of Application アプリケーション説明 Inspection succeeded. Select an object to be 検査 OK。 inspected. SWITCH SWITCH 検査対象を選択する。 Inspection was failed. 検査 NG。 Object to be inspected is displayed. 検査対象が表示される。 ・ □にチェック印をつけると検査対象となる。 ・ 個別に選択して、単体検査ができる。 Information such as version is ・...
Page 50
DSR112/DSR115/DSR215/DSR118W 検査対象が表示される。 ・ □にチェック印をつけると検査対象となる。 ・ 個別に選択して、単体検査ができる。 Information such as version is ・ 個別に選択して、ダブルクリックすると詳細な検査項目が displayed. 表示される。 バージョン等の情報が表示される。 Details of inspection result are displayed. 検査結果の詳細を表示する。 (検査の実行&停止) (テストのスタート) (テストの一時停止) (テストの停止) (結果のクリア) (テストの実行) (ログの保存) (出力文字列の保存) Property window ( ⑦ ) (7) プロパティウインドウ(⑦) List of character strings obtained by test is displayed.
DSR112/DSR115/DSR215/DSR118W ■ INSPECTIONS (検査) DSR112/DSR115/DSR215 DSR112/DSR115/DSR215 This test specifi cation is applied to the AMP assembly 112/115/215. この検査規格はアンプ Ass'y 112/115/215 に適用されます。 Measurement Conditions 測定条件 1-1. Measuring Instrument and jigs 1-1. 測定器、冶具 • Use a reliable measuring device capable of precisely ・...
Page 52
DSR112/DSR115/DSR215/DSR118W 1-3. Preparation 1-3. 準備 • The load resistors for each output terminals are as ・ 各出力端子に下記の負荷抵抗を接続します。 follows. SP OUT(CN300) :4 Ω(定格 500W 以上) SP OUT(CN300) : 4 Ω (Rated 500W or more) SP OUT(CN500) :8 Ω(定格 100W 以上) SP OUT(CN500) : 8 Ω...
Page 53
DSR112/DSR115/DSR215/DSR118W 2-2. Adjustment 2-2. 調整 The tip of the screwdriver for adjustment must be ※ 調整用ドライバーは必ず先端が絶縁素材のものを insulation material. 使用すること。 Perform adjustment with no signal input ※ 調整は入力無信号の状態で行います。 (1) Adjustment of PFC voltage and ± B voltage (1) PFC 電圧および ± B 電圧の調整...
Page 54
DSR112/DSR115/DSR215/DSR118W (2) Adjustment of offset voltage of amplifi er output (2) アンプ出力のオフセット電圧の調整 Start adjustment longer than 5 seconds after the ※ 電源をオンした後、5 秒以上待ってから調整 power switch is turned on. を始めてください。 • Adjust VR300 so that the voltage across 1 pin – 2 ・...
Page 55
DSR112/DSR115/DSR215/DSR118W 2-10. Confi rmation of switch 2-10. スイッチの確認 Execute SWITCH inspection of diagnostic mode. ダイアグモードの SWITCH 検査を実行します。 Confi rm that each switch operates properly. 各スイッチが正常に動作することを確認します。 2-11. Gain (LINE) 2-11. 利得(LINE) (1) Input the 1 kHz, -9.5 dBu sine wave to the input terminal (1)...
Page 56
DSR112/DSR115/DSR215/DSR118W 2-14. Maximum Output 2-14. 最大出力 (1) Input the 100 Hz, sine wave to the input terminal (XLR). (1) 入力端子 (XLR) へ 100 Hz の正弦波を入力します。 Confi rm that the total harmonic distortion is 1.0 % or SP OUT(CN300)に 35.23 dBu(500 W/4 Ω)が...
Page 57
DSR112/DSR115/DSR215/DSR118W 2-20. Analog mute inspection 2-20. アナログ MUTE 検査 Execute A-MUTE inspection of diagnostic mode. ダイアグモードの A-MUTE を実施します。 Input the 1 kHz, -9.5 dBu sine wave to the input terminal 入力端子 (XLR) に 1 kHz、 -9.5 dBu の正弦波を入力し、 (XLR), turn on /A-MUTE signal and confirm that the /A-MUTE 信号を...
Page 58
DSR112/DSR115/DSR215/DSR118W Discharging capacitors コンデンサの放電 The capacitors C118 and C119 on the AMPS circuit board AMPS シートのコンデンサー C118、C119 には電源 maintain a high voltage even when the power is switched OFF 状態でも高電圧が残ります。 off. To avoid an electrical shock and malfunction, discharge 感電及び故障の防止のために残った電圧を下記の方...
Page 59
DSR112/DSR115/DSR215/DSR118W DSR118W DSR118W This inspection specifi cation is applied to the AMP assembly 118. この検査規格は、アンプ Ass'y 118 に適用されます。 Measurement Conditions 測定条件 1-1. Measuring Instrument and jigs 1-1. 測定器、冶具 • Use a reliable measuring device capable of precisely ・ 検査に使用する測定器は、本文中に記載の規格を measuring the specification values indicated in this 十分精度良く測定できる精度及び確度を持つもの...
Page 60
DSR112/DSR115/DSR215/DSR118W 1-3. Preparation 1-3. 準備 • The load resistor for output terminal is as follows. ・ 出力端子に下記の負荷抵抗を接続します。 SP OUT (CN300) : 4 Ω (Rated 500 W or more) SP OUT(CN300) :4 Ω(定格 500 W 以上) • 0 dBu is referenced to 0.775 Vrms.
Page 61
DSR112/DSR115/DSR215/DSR118W (1) Adjustment of PFC voltage and ± B voltage (1) PFC 電圧および ± B 電圧の調整 Adjust VR101 so that the PFC voltage is 399.8 V – PFC 電 圧 が 399.8 V − 400.2 V と な る よ う に...
Page 62
DSR112/DSR115/DSR215/DSR118W (2) Adjustment of offset voltage of amplifi er output (2) アンプ出力のオフセット電圧の調整 Start adjustment longer than 5 seconds after the ※ 電源オン後、5秒以上待ってから調整を始め power supply is turned on. てください。 Adjust VR300 so that the voltage across 1 pin – 2 CN300 の 1 ピン− 2 ピン間の電圧が 0 V ± 2 mV pin of CN300 is 0 V ±...
Page 63
DSR112/DSR115/DSR215/DSR118W 2-9. Frequency Response 2-9. 周波数特性 (1) Input the -20 dBu sine wave to the INPUT L terminal. (1) INPUT L 端子に -20 dBu の正弦波を入力し、各 周波数での出力レベルが下記の規定範囲内にあ Confirm that the output level at each frequency is ることを確認します。 within the specifi ed in the table below.
Page 64
DSR112/DSR115/DSR215/DSR118W Turn the power switch off and on again, and confirm 電源スイッチを OFF し、再度 ON して、本体が that the unit operates properly. 正常に動作することを確認します。 (2) Input DC -1 V between 1 pin and 3 pin (GND) of CN907 (2) BRG4 シートの CN907 の 1 ピンと 3 ピンに DC of the BRG4 circuit board.
Page 65
DSR112/DSR115/DSR215/DSR118W Discharging capacitors コンデンサの放電 The capacitors C118 and C119 on the AMPS circuit board AMPS シートのコンデンサー C118、C119 には電源 maintain a high voltage even when the power is switched OFF 状態でも高電圧が残ります。 off. To avoid an electrical shock and malfunction, discharge 感電及び故障の防止のために残った電圧を下記の方...
DSR112/DSR115/DSR215/DSR118W ■ UPDATING (アップデート) This fi rmware updating procedure is applied to DSR112, DSR115 こ の フ ァ ー ム ウ ェ ア ア ッ プ デ ー ト 手 順 は、DSR112、 and DSR215. DSR115、DSR215 に適用されます。 CAUTION 注意 Since the calibration data written in the flash ROM is initialized ファームウェアをアップデートするとフラッシュ...
Page 67
DSR112/DSR115/DSR215/DSR118W Operation procedures 操作方法 4-1. Short circuit between pin 5 (CPU-MODE) and pin 3 (GND) 4-1. BRG シートのコネクター CN907 の 5 ピン (CPU-MODE) of connector CN907 on the BRG circuit board, and turn on と 3 ピン(GND)をショートし、アンプ Ass'y の電源 the power switch. The fi rmware update mode is activated.
Page 68
DSR112/DSR115/DSR215/DSR118W 4-4. Click “F/W Update(W)”. 4-4. 「F/W Update(W) 」をクリックします。 4-5. Click “OK” to start updating. 4-5. 「OK」をクリックしてアップデートを開始します。 In process of writing (書き込み中) In process of verifying writing (書き込みチェック中) Writing is completed (書き込み完了) 4-6. Click “OK”. 4-6. 「OK」をクリックすると、アプリケーションを自動的 に終了します。 The application ends automatically.
Page 69
DSR112/DSR115/DSR215/DSR118W 4-7. Turn off the power switch of AMP UNIT. 4-7. AMP UNIT の Power スイッチをオフします。 ※ 書き込み中にエラーが発生したり、長時間待っ When error occurs while writing or writing does not complete although long time has passed, perform ても書き込みが完了しないときは、 ファームウェ the updating procedure again from the beginning.
Page 70
DSR112/DSR115/DSR215/DSR118W 問題: Problem: “DSR.id” (ID file) does not exist in file path specified in Update.ini ファイル内で指定されたファイルパスに Update.ini fi le. DSR.id(ID ファイル)が存在しない。 Countermeasure: 対策: Store “DSR.id” (ID fi le) in path specifi ed in Update.ini fi le. Update.ini ファイル内で指定されたファイルパスに DSR.id(ID ファイル)を格納します。...
Page 71
DSR112/DSR115/DSR215/DSR118W 問題: Problem: Assigned COM port does not exist, or it can not opened 指定された COM ポートが存在しない、または他のア because in use by other application (e.g. inspection プリ (例えば検査アプリケーション)で使用中のた application). め開けない。 Countermeasure: 対策: Check that COM port assigned in Update.ini fi le can open ファイル内で指定された...
DSR112/DSR115/DSR215/DSR118W ■ OVERALL CIRCUIT DIAGRAM (総回路図) IN1/IN2/IN3 DSR112/DSR115/DSR215 OP AMP OP AMP Installed Not installed Part No. to DSP_CN101 <P. 8 / O9> to DSP_CN102 <P. 8 / O11> Note: XX : Not installed ( 未実装 ) 2001063338-1 28CC1-...
DSR112/DSR115/DSR215/DSR118W DSP 1/3 DSR112/DSR115/DSR215 SYSTEM RESET to BRG1/BRG2/BRG3_CN901 <P. 11 / E2> to BRG1/BRG2/BRG3_CN902 <P. 11 / E4> to IN1/IN2/IN3_CN803 <P. 7 / F6> to IN1/IN2/IN3_CN804 <P. 7 / I6> Note: XX : Not installed ( 未実装 ) 2001063495-1 28CC1-...
Page 119
DSR112/DSR115/DSR215/DSR118W DSP 2/3 DSR112/DSR115/DSR215 A/D CONVERTER OP AMP OP AMP OP AMP Note: XX : Not installed ( 未実装 ) 2001063495-2 28CC1-...
Page 120
DSR112/DSR115/DSR215/DSR118W DSP 3/3 DSR112/DSR115/DSR215 DC/DC CONVERTER REGULATOR +5 V REGULATOR REGULATOR DC/DC CONVERTER Note: XX : Not installed ( 未実装 ) 2001063495-3 28CC1-...
Page 121
DSR112/DSR115/DSR215/DSR118W BRG1/BRG2/BRG3 / LED DSR112/DSR115/DSR215 to AMPS1_CN701 <P. 15 / A2> to DSP_CN103 <P. 8 / O6> to DSP_CN104 <P. 8 / O8> to AMPS1_CN702 <P. 15 / A3> 28CC1- 2001063338-2 28CC1- 2001063500 Note: XX : Not installed ( 未実装 )
DSR112/DSR115/DSR215/DSR118W ■ WARNING ACIN / AMPS1 1/4 Components having special characteristics are marked and must be replaced with parts DSR112/DSR115/DSR215 having specification equal to those originally installed. ■ 安全上の注意 connector assembly AC IN POWER 印の商品は、安全を維持するために重要な部品です。交換する場合は、安全のために必ず指定の部 SWITCH White 品をご使用ください。 (白) Black (黒)...
Page 123
DSR112/DSR115/DSR215/DSR118W AMPS1 2/4 DSR112/DSR115/DSR215 to Woofer Note: XX : Not installed ( 未実装 ) 2001063527-2 28CC1-...
Page 124
DSR112/DSR115/DSR215/DSR118W AMPS1 3/4 DSR112/DSR115/DSR215 to Tweeter Note: XX : Not installed ( 未実装 ) 2001063527-3 28CC1-...
Page 125
DSR112/DSR115/DSR215/DSR118W AMPS1 4/4 DSR112/DSR115/DSR215 to BRG1/BRG2/BRG3_CN904 <P. 11 / B1> Note: XX : Not installed ( 未実装 ) to BRG1/BRG2/BRG3_CN903 <P. 11 / B3> 2001063527-4 28CC1-...
DSR112/DSR115/DSR215/DSR118W DSR118W OP AMP OP AMP OP AMP to BRG4_CN902 to BRG4_CN901 <P. 18 / E4> <P. 18 / E1> to IN4_CN202 <P. 16 / E8> REGULATOR OP AMP REGULATOR Note: XX : Not installed ( 未実装 ) 2001063346-1 28CC1-...
Page 128
DSR112/DSR115/DSR215/DSR118W BRG4 / LED DSR118W to AMPS2_CN701 <P. 21/ A2> to ASP_CN303 <P. 17 / B4> to AMPS2_CN702 <P. 21 / A3> to ASP_CN302 <P. 17 / E4> 2001063344-2 28CC1- 2001063500-1 28CC1- Note: XX : Not installed ( 未実装 )
Page 129
DSR112/DSR115/DSR215/DSR118W ■ WARNING AC IN / AMPS2 1/3 Components having special characteristics are marked and must be replaced with parts DSR118W having specification equal to those originally installed. ■ 安全上の注意 connector assembly AC IN POWER 印の商品は、安全を維持するために重要な部品です。交換する場合は、安全のために必ず指定の部 SWITCH White 品をご使用ください。 (白)...
Page 130
DSR112/DSR115/DSR215/DSR118W AMPS2 2/3 DSR118W to Woofer Note: XX : Not installed ( 未実装 ) 2001063527-2 28CC1-...
Page 131
DSR112/DSR115/DSR215/DSR118W AMPS2 3/3 DSR118W Note: XX : Not installed ( 未実装 ) to BRG4_CN904 <P. 18 / B1> to BRG4_CN903 <P. 18 / B3> Note: XX : Not installed ( 未実装 ) 2001063527-4 28CC1-...